0343505 EVINRUDE SCREW, Cover


0343505 SCREW, Cover EVINRUDE E100FPLSOC, E100FPLSRS, E100WPLSIF, E105WELSIF, E105WELSSC, E115FPLEEC, E115FPLSDS, E115FPLSIF, E115FPLSNF, E115FPLSOD, E115FPLSRE, E115FPLSSH, E115FPLSTB, E115FPXSDS, E115FPXSOD, E115FPXSRE, E115FSLECS, E115FSLSDS, E135FCXSDE, E135FCXSIF, E135FCXSNF SCREW
0343505 SCREW, Cover EVINRUDE
Rating:
43

Buy SCREW, Cover 0343505 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 37
 

BRP EVINRUDE entire parts catalog list:

E100FPLSOC, E100FSLSOC 2004,2005
E100FPLSRS, E100FSLSRS 2004
E100WPLSIF, E100WPXSIF 2001
E105WELSIF, E105WPLSIF, E105WPXSIF 2001
E105WELSSC, E105WPLSSC, E105WPXSSC 2000
E115FPLEEC, E115FPLEEN, E115FPXEEC, E115FPXEEN, E115FSLEEC, E115FSLEEN 1999
E115FPLSDS 2006
E115FPLSIF, E115FPXSIF, E115FSLSIF, RE115FLSIF, RE115FSSIF, RE115FXSIF 2001
E115FPLSNF, E115FPXSNF 2002
E115FPLSOD, E115FSLSOD 2004,2005
E115FPLSRE, E115FSLSRE 2004
E115FPLSSH, E115FPLSSR, E115FPXSSH, E115FPXSSR, E115FSLSSH, E115FSLSSR, RE115FLSSSH, RE115FLSSSR, RE115FPLSSH, RE115FPLSSR, RE115FSSSH, RE115FSSSR, RE115FXSSH, RE115FXSSR 2000
E115FPLSTB, E115FPXSTB, E115FSLSTB 2003
E115FPXSDS 2006
E115FPXSOD 2004,2005
E115FPXSRE 2004
E115FSLECS, E115FSXECS, E115FTLECS 1998
E115FSLSDS 2006
E135FCXSDE 2006
E135FCXSIF, E135FPLSIF, E135FSLSIF, E135FSXSIF, RE135FCSIF, RE135FLSIF, RE135FXSIF 2001
E135FCXSNF, E135FPLSNF, E135FPXSNF 2002
E135FCXSOB 2004,2005
E135FCXSRM 2004
E135FCXSSS, E135FPLSSS, E135FSLSSS, E135FSXSSS, RE135FCSSS, RE135FLSSS, RE135FXSSS 2000
E135FCXSTA 2003
E135FPLSDE 2006
E135FPLSOB, E135FSLSOB 2004,2005
E135FPLSRM, E135FSLSRM 2004
E135FPLSTA, E135FPXSTA 2003
E135FPLSTF 2003
E135FPXSDE 2006
E135FPXSOB 2004,2005
E135FPXSRM 2004
E135FSLSDE 2006
E135FSLSTA 2003
E135FSLSTF 2003
E150FCXECR, E150FSLECR, E150FSXECR, E150ILECR 1998
E150FCXEEA, E150FCXEEN, E150FCXEEO, E150FPLEEA, E150FPLEEO, E150FPXEEA, E150FPXEEN, E150FPXEEO, E150FSLEEA, E150FSLEEO 1999
E150FCXSDR 2006
E150FCXSIF, E150FPLSIF, E150FPXSIF, E150FSLSIF, RE150FCSIF, RE150FLSIF, RE150FSSIF, RE150FXSIF 2001
E150FCXSNF, E150FPLSNF, E150FPXSNF 2002
E150FCXSOC 2004,2005
E150FCXSRS 2004
E150FCXSSM, E150FCXSSV, E150FPLSSM, E150FPLSSV, E150FPXSSM, E150FPXSSV, E150FSLSSM, E150FSLSSV, RE150FCSSM, RE150FCSSV, RE150FLSSM, RE150FLSSV, RE150FSSM, RE150FSSV, RE150FXSSM, RE150FXSSV 2000
E150FCXSTD 2003
E150FHLSDR 2006
E150FHLSOC 2004,2005
E150FHLSRS 2004
E150FPLSDR 2006
E150FPLSOC, E150FSLSOC 2004,2005
E150FPLSRS, E150FSLSRS 2004
E150FPLSTD, E150FPXSTD, E150FSLSTD 2003
E150FPLSTF 2003
E150FPXSDR 2006
E150FPXSOC 2004,2005
E150FPXSRS 2004
E150FSLSDR 2006
E150FSLSTF 2003
E150ICXEUC, E150ILEUC, E150IXEUC, E150PLEUC 1997
E150WPLSIF 2001
E150WPLSSC 2000
E175FCXECS, E175FSLECS, E175FSXECS, E175FTLECS 1998
E175FCXEEC, E175FCXEEN, E175FCXEEO, E175FPLEEC, E175FPLEEO, E175FPXEEC, E175FPXEEN, E175FPXEEO, E175FSLEEO, E175FSLEES 1999
E175FCXSDS 2006
E175FCXSIF, E175FPLSIF, E175FPXSIF, E175FSLSIF, RE175FCSIF, RE175FLSIF, RE175FSSIF, RE175FXSIF 2001
E175FCXSNF, E175FPLSNF, E175FPXSNF 2002
E175FCXSOD 2004,2005
E175FCXSRE 2004
E175FCXSSR, E175FCXSSV, E175FPLSSR, E175FPLSSV, E175FPXSSR, E175FPXSSV, E175FSLSSC, E175FSLSSV, RE175FCSSR, RE175FCSSV, RE175FLSSR, RE175FLSSV, RE175FSSC, RE175FXSSR, RE175FXSSV 2000
E175FCXSTB 2003
E175FPLSDS 2006
E175FPLSOD, E175FSLSOE 2004,2005
E175FPLSRE, E175FSLSRB 2004
E175FPLSTB, E175FPXSTB, E175FSLSTM 2003
E175FPLSTF 2003
E175FPXSDS 2006
E175FPXSOD 2004,2005
E175FPXSRE 2004
E175FSLSDD 2006
E175FSLSTF 2003
E175MFXSOS 2005
E175MFXSOS 2004
E55MJRLAAA 2012
E55MJRLIIM 2011
E55MJRLINB 2012
E55MJRLISA 2010
E55MJRLSCC 2008
E55MJRLSEF 2009
E55MJRLSER 2009
E55MRLAAA 2012
E55MRLIIM 2011
E55MRLINB 2012
E55MRLISA 2010
E55MRLSCC 2008
E55MRLSEF 2009
E55MRLSER 2009
E75FPLSIF, E75FVLSIF, RE75FPLSIF 2001
E75FPLSNF 2002
E75FPLSSH, RE75FPLSSH 2000
E75FPLSTA 2003

Information:


Table 1
Diagnostic Trouble Codes
J1939 Code CDL Code Code Description Comments
190-8 190-8 Engine Speed Sensor : Abnormal Frequency, Pulse Width, or Period The code is logged. The Electronic Control Module (ECM) can default to the secondary engine speed/timing sensor. The default will occur if a valid signal is not received from the primary engine speed/timing sensor. The engine will shut down only if the signals from the primary engine speed/timing sensor and the secondary engine speed/timing sensor are abnormal.
723-8 342-8 Secondary Engine Speed Sensor : Abnormal Frequency, Pulse Width, or Period The code is logged. If a valid signal is not received from the secondary engine speed/timing sensor, the ECM will default to the primary engine speed/timing sensor. The engine will shut down only if the signals from the primary engine speed/timing sensor and the secondary engine speed/timing sensor are abnormal. The engine uses two engine speed/timing sensors. Both sensors detect the reference for engine speed and timing from a unique pattern on the camshaft gear. The ECM uses the pattern of the pulses in order to determine the position of the crankshaft. The ECM measures the time between the pulses that are created by the sensors as the gears rotate in order to determine rpm.Under normal operation, the secondary engine speed/timing sensor is used to determine timing for starting purposes. The secondary engine speed/timing sensor is used to determine when the piston in the No. 1 cylinder is at the top of the compression stroke. The primary engine speed/timing sensor is then used to determine engine speed and the signal from the secondary camshaft sensor is ignored.After locating the No. 1 cylinder, the ECM triggers each injector in the correct firing order and at the correct unit injector timing. The actual timing and duration of each injection is based on engine rpm and load. If the engine is running and the signal from the primary engine speed/timing sensor is lost, a slight change in engine performance will be noticed. The change will be noticed when the ECM performs the changeover to the secondary engine speed/timing sensor. Loss of the signal from the secondary engine speed/timing sensor during engine operation will not result in any noticeable change in engine performance. However, if the signal from the secondary engine speed/timing sensor is not present during start-up the following conditions may exist:
The engine may require a slightly longer amount of time to start up.
The engine may run rough for a few seconds until the ECM determines the proper firing order by using the primary engine speed/timing sensor only.The engine will start and the engine will run when only one sensor signal is present from either of the sensors. Loosing the signal from both of the sensors during engine operation will result in the termination of injection. The ECM will then shut down the engine. The loss of the signal from both of the sensors during start-up will prevent the engine from starting.Both sensors are magnetic sensors with an integral connector. The two sensors are not interchangeable. Do not switch the positions of the sensor. If the sensors are replaced, a timing calibration is not necessary for the engine.
Illustration 1 g01199875
Schematic for the engine speed/timing sensors
Table 2
Troubleshooting Test Steps Values Results
1. Check the Engine Speed/Timing Circuit
A. Connect Cat® Electronic Technician (ET) to the service tool connector. Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Turn the keyswitch to the ON position.
C. Monitor the "Engine Starting" screen in Cat ET
Start the engine and run the engine. The problem may occur when the engine is at any operating temperature. However, the problem is more likely to occur when the engine is at the normal operating temperature.
Circuit Check
Result: The engine started.
Proceed to Test Step 2.
Result: The engine did not start.
Proceed to Test Step 3.
2. Check for Diagnostic Codes
A. While the engine is running monitor Cat ET for diagnostic codes. Also monitor the "Engine Starting" screen for an engine speed/timing that is "Not Detected".
B. Wait at least 30 seconds for activation of the diagnostic codes. Look for these codes on Cat ET:
190-8
342-8
Diagnostic Codes
Result: There is an active diagnostic code or there is a timing pattern that is "Not Detected".
Proceed to Test Step 5.
Result: There is not an active diagnostic code and there is not a timing pattern that is "Not Detected".
Repair: Download the "Warranty Report" from the engine ECM. Troubleshoot any diagnostic codes that may be present.
Return the unit to service.
STOP
3. Check the Battery Voltage
A. Monitor the "Engine Starting" screen in Cat ET.
B. Monitor the battery voltage. Crank the engine for 5 seconds.
Battery Voltage
Result: The battery voltage is OK.
Proceed to Test Step 4.
Result: The battery voltage is not OK.
Repair: Refer to Troubleshooting, "Engine Cranks but Does Not Start".
4. Check the Engine Speed and the Engine Speed/Timing Status
A. Monitor the "Engine Starting" screen in Cat ET.
B. Crank the engine for 5 seconds. While the engine is cranking, verify that the sensors show an acceptable cranking speed.
C. While the engine is cranking check the status of the engine speed/timing.
Speed/Timing Status
Result: The sensors show an acceptable cranking speed. The timing pattern shows "Detected".
Repair: Refer to Troubleshooting, "Engine Cranks but Does Not Start".
Result: A sensor does not show an acceptable cranking speed and/or the timing pattern shows "Not Detected".
Proceed to Test Step 5.
Illustration 2 g03781728
Typical left side engine view
(1) Rear surface of the front timing gear housing
(2) Mounting flange
(3) Bracket
Table 3
Troubleshooting Test Steps Values Results
5. Inspect the Sensor Assembly
A. Turn the keyswitch to the OFF position.
B. Visually inspect the sensor and the sensor assembly without removing the sensor assembly from the engine. Flanges (2) must be flush against the surface of the front timing gear housing (1) in order to ensure proper operation.
C. Inspect bracket (3). Verify that the bracket securely holds the flanges of the sensors flush against the engine.
D. Verify that the bracket is not bent. If the bracket is bent or if an obstruction is preventing the sensor assembly from being installed correctly, the engine will not start.
E. Disconnect the harness from the sp


Parts screw EVINRUDE:

0305513
 
0305513 SCREW,Pivot shaft
100193A, 100293R, 100882B, 115083D, 115983E, 125183C, 125283R, 40102B, 50172S, 50542B, 50902C, 55642E, 55772D, 55872A, 55874S, 55972A, 60172C, 65272S, 65832B, 85093B, 85193A, 85293R, 85852A, 85892A, BE25ARECA, BE25AREDC, BE25AREUR, BE35ARECR, BE35ARE
0318544
SCREW, Drain and fill
0318544 SCREW, Drain and fill
100990S, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 50302R, 50442M, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 70973R, 75542B, 75642D, 85393M, 85493B, 855
0324816
 
0324816 SCREW, Housing to cylinder
B25JREUR, BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20
0328694
SCREW, Front to rear cover
0328694 SCREW, Front to rear cover
B25JREUR, BE115ELEDR, BE115TLEDA, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20SREDA, BE20SREUM, BE225CXECS, BE225CXEDE, BE225CXEUD, BE25BA
0328724
SCREW, Clamp to anchor block
0328724 SCREW, Clamp to anchor block
BE10EEDD, BE10RELEUS, BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE15EEDS, BE15RELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA, BE20SEECB, BE2
0330263
SCREW, Gearcase to housing, rear
0330263 SCREW, Gearcase to housing, rear
BE115ELEDR, BE115ELEUA, BE115GLECM, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, BE90ELEDR, BE90ELEUA, BE90SLECM, D
0315656
SCREW, Cover plate
0315656 SCREW, Cover plate
BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE115ELEDR, BE115ELEUA, BE115GLECM, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA,
0125529
 
0125529 SCREW, Housing to tank
BE10EEDD, BE10FAEDC, BE10FDLEDR, BE15EEDS, BE15FAEDR, BE20SEEDA, BE20SREDA, BE25BAEDR, BE25EEDM, BE30BAEDE, BE30EEDE, BE40EEDS, BE50BEEDS, BE50DTLEDC, BE5FRBEUS, BE60ELEDR, BE70ELEDA, BE8FRBEDC, E10EENA, E10EEOE, E10EERB, E10EETM, E10FEXEO, E115FSLEC
Back to top