0911859 SCREW, Ground strap EVINRUDE
E100STLEIE, E100STLEND, E115JLEIE, E115JLEND, E88MSLEIM, E88MSLEIM, E88MSLENB, E88MSLENB
SCREW
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- TRANSOM BRACKET ASSY. - QUIET RIDER » 0911859
E115JLEIE, E115MLEIE, E115TLEIE, E115TXEIE, TE115TLEIE, VE115TLEIE, VE115TXEIE 1991
E115JLEND, E115MLEND, E115TLEND, E115TXEND, TE115TLEND 1992
E88MSLEIM, E90JLEIE, E90TLEIE, TE90TLEIE, VE90MLEIE, VE90TLEIE 1991
E88MSLEIM 1991
E88MSLENB 1992
E88MSLENB, E90JLEND, E90TLEND, TE90TLEND, VE90MLEND, VE90TLEND 1992
Information:
start by: a) remove turbocharger 1. Install the turbocharger on tool (A).2. Put marks on the housings for correct installation at assembly.3. Loosen clamp (1). Remove compressor housing (2). Remove the clamp. 4. Remove bolts (3), locks (6) and plates (5).5. Remove the center section from turbine housing (4). 6. Install tool (C) in tool (B). Install the center section in tool (C) as shown.7. Remove nut (7) that holds the impeller to the shaft and wheel assembly. 8. Install tool (E) on tool (D). Heat tool (D) to 350°F (177°C). Install the impeller on tool (E).
Make sure only the impeller is in the hot oil.
9. Install tool (E) with the center section on tool (F). Remove impeller (9) with an arbor press (8) and tool (G). Step 9 must be done before the impeller gets cold. 10. Remove shaft and wheel assembly (10), shroud (11) and spacer (13) from center housing (12). 11. Remove bolts (14), locks (15) and plate (16) from the center housing. 12. Remove collar (17). 13. Remove two bearings (18) and three snap rings (19) from the center housing.Assemble Turbocharger (Precombustion Chamber)
1. Clean all parts thoroughly before assembly. 2. Install snap ring (15), bearing (12) and snap ring (11) in center housing (10). Install snap ring (9) and bearing (8). Put 4L7464 Silicone Grease in the seal ring groove of the shaft and wheel assembly. Make sure it fills approximately one half or more of the groove depth for the complete circumference of the groove. Install ring seal (14) on the shaft and wheel assembly.3. Install shroud (13) and shaft and wheel assembly (16) in the center housing.
Use caution not to cause damage to ring seal (14) when the shaft and wheel assembly are installed.
4. Install spacer (7) and collar (6).5. Put plate (5) in position on the center housing. Install bolts (4). Tighten the bolts to a torque of 35 5 lb.in. (4.0 0.6 N m).6. Install spacer (3). Make sure the small inside diameter of the spacer is toward the impeller end of the shaft and wheel assembly.
If spacer (3) is installed with its small inside diameter toward the center housing it will cause a restriction of oil flow to the chamber and rings. This will cause a failure to the turbocharger.
7. Heat impeller (1) in oil to a maximum temperature of 350°F (177°C). Install the impeller on the shaft and wheel assembly. 8. Install tool (C) in tool (B). Instll the center section in tool (C). Install nut (2). Tighten the nut to a torque of 120 lb.in. (13.6 N m). Let the temperature of the impeller get below 150°F (65°C). Loosen the nut. Put a light amount of oil on the threads of the shaft and wheel assembly. Tighten the nut again to a torque of 30 lb.in. (3.4 N m). Put a mark on the nut and impeller. Tighten the nut 120° past the mark.
Do not put a bending force on the shaft and wheel assembly when nut (2) is tightened.
9. Install turbine housing (17) on tool (A). Install the center section in the turbine housing. Put the marks that were made at disassembly in alignment to make sure the housings are in their original position. 10. Put 5P3931 Anti-Seize Compound on the threads of bolts (21). Install plates (20), locks (19) and the bolts. Tighten the bolts to a torque of 175 15 lb.in. (19.8 1.7 N m).11. Install a new O-ring seal (18) on the center housing. 12. Put clamp (23) over the center section. Put compressor housing (22) in alignment with the marks made at disassembly. Put the clamp in position over the housing. Tighten the clamp to a torque of 120 10 lb.in. (13.6 1.1 N m).13. Put oil in the center section and turn the shaft and wheel assembly.end by: a) install turbocharger
Make sure only the impeller is in the hot oil.
9. Install tool (E) with the center section on tool (F). Remove impeller (9) with an arbor press (8) and tool (G). Step 9 must be done before the impeller gets cold. 10. Remove shaft and wheel assembly (10), shroud (11) and spacer (13) from center housing (12). 11. Remove bolts (14), locks (15) and plate (16) from the center housing. 12. Remove collar (17). 13. Remove two bearings (18) and three snap rings (19) from the center housing.Assemble Turbocharger (Precombustion Chamber)
1. Clean all parts thoroughly before assembly. 2. Install snap ring (15), bearing (12) and snap ring (11) in center housing (10). Install snap ring (9) and bearing (8). Put 4L7464 Silicone Grease in the seal ring groove of the shaft and wheel assembly. Make sure it fills approximately one half or more of the groove depth for the complete circumference of the groove. Install ring seal (14) on the shaft and wheel assembly.3. Install shroud (13) and shaft and wheel assembly (16) in the center housing.
Use caution not to cause damage to ring seal (14) when the shaft and wheel assembly are installed.
4. Install spacer (7) and collar (6).5. Put plate (5) in position on the center housing. Install bolts (4). Tighten the bolts to a torque of 35 5 lb.in. (4.0 0.6 N m).6. Install spacer (3). Make sure the small inside diameter of the spacer is toward the impeller end of the shaft and wheel assembly.
If spacer (3) is installed with its small inside diameter toward the center housing it will cause a restriction of oil flow to the chamber and rings. This will cause a failure to the turbocharger.
7. Heat impeller (1) in oil to a maximum temperature of 350°F (177°C). Install the impeller on the shaft and wheel assembly. 8. Install tool (C) in tool (B). Instll the center section in tool (C). Install nut (2). Tighten the nut to a torque of 120 lb.in. (13.6 N m). Let the temperature of the impeller get below 150°F (65°C). Loosen the nut. Put a light amount of oil on the threads of the shaft and wheel assembly. Tighten the nut again to a torque of 30 lb.in. (3.4 N m). Put a mark on the nut and impeller. Tighten the nut 120° past the mark.
Do not put a bending force on the shaft and wheel assembly when nut (2) is tightened.
9. Install turbine housing (17) on tool (A). Install the center section in the turbine housing. Put the marks that were made at disassembly in alignment to make sure the housings are in their original position. 10. Put 5P3931 Anti-Seize Compound on the threads of bolts (21). Install plates (20), locks (19) and the bolts. Tighten the bolts to a torque of 175 15 lb.in. (19.8 1.7 N m).11. Install a new O-ring seal (18) on the center housing. 12. Put clamp (23) over the center section. Put compressor housing (22) in alignment with the marks made at disassembly. Put the clamp in position over the housing. Tighten the clamp to a torque of 120 10 lb.in. (13.6 1.1 N m).13. Put oil in the center section and turn the shaft and wheel assembly.end by: a) install turbocharger
Parts screw EVINRUDE:
0316563
0316563 SCREW
100193A, 100293R, 100990S, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 85193A, 85293R, 85393M, 85493B, 85593E, 85693D, BE115TLEDA, E100MLCSC,
0318544
0318544 SCREW, Drain and fill
100990S, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 50302R, 50442M, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 70973R, 75542B, 75642D, 85393M, 85493B, 855
0317972
0317972 SCREW, Exhaust manifold to cylinder long
100990S, 115790S, 115890C, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, BE115TLEDA, E100FPLSOC, E100FPLSRS, E100MLCSC, E100STLCCA, E100STLCEM, E100STLEIE, E100STLEND, E100STLERC, E100STLESB, E100STLETS, E100WPLSIF, E105WELSIF, E110MLCCA, E11
0319137
0319137 SCREW, Hook
100990S, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 85493B, 85593E, 85693D, C155WTLM, CE275TLCDC, CE275TLCOS, CE300TLCDC, CE300TLCOS, E100MLCSC, E100STLCCA, E100STLCEM, E100STLE
0325135
0325135 SCREW, Stator mounting
100990S, 150940C, BE115TLEDA, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, BE250CXECB, BE250CXEDA, BE250CXEUM, CE275TLCDC, CE300TLCDC, E100MLCSC, E100STLCCA, E100STLCEM, E100STLEIE, E100STLEND, E100STLERC, E100STLESB, E100S
0328720
0328720 SCREW,Cover to base
BE115TLEDA, E100STLCCA, E100STLCEM, E100STLEIE, E100STLEND, E100STLERC, E100STLESB, E100STLETS, E100WMLCDR, E100WMLCOC, E100WMLCRS, E110MLCCA, E110MLCDC, E110MLCEM, E110MLCUR, E112TSLEDR, E112TSLEDR, E112TSLEOC, E112TSLEOC, E112TSLERS, E115JKLEOC, E1
0328694
0328694 SCREW, Front to rear cover
B25JREUR, BE115ELEDR, BE115TLEDA, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20SREDA, BE20SREUM, BE225CXECS, BE225CXEDE, BE225CXEUD, BE25BA
0328724
0328724 SCREW, Clamp to anchor block
BE10EEDD, BE10RELEUS, BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE15EEDS, BE15RELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA, BE20SEECB, BE2