5040266 SCREW EVINRUDE
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
SCREW
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$34.99
14-09-2017
Partsmaste: Partsmaster Tire Rep
Partsmaster Tire Repair 5040266 Chrm Flsh Mnt Vlv Box Of 50
Compatible models:
B10EL4AAA
B10EL4AAB
B10EL4INS
B10PL4AAA
B10PL4AAB
B10PL4INS
B10PX4INS
B10R4AAA
B10R4AAB
B10R4INS
B10RL4INS
B10TEL4AAA
B10TEL4INS
B10TPL4AAA
B10TPL4AAB
B10TPL4INS
B10TPX4INS
B15PL4AAA
B15PL4INS
B15R4AAA
B15R4AAB
B15R4INS
B15RL4INS
B15TE4INS
E10EL4AAB
E10EL4INS
E10PL4INS
E10TEL4AAB
E15PL4INS
E15R4INS
EVINRUDE
BRP EVINRUDE entire parts catalog list:
- SIDE MOUNT REMOTE CONTROL » 5040266
B10EL4INS 2012
B10PL4AAA, B10PX4AAA, E10PL4AAA, E10PX4AAA 2012
B10PL4AAB, B10PX4AAB, E10PL4AAB, E10PX4AAB 2012
B10PL4INS 2012
B10PX4INS, E10PX4INS 2012
B10R4AAA, B10RL4AAA, E10R4AAA, E10RL4AAA 2012
B10R4AAB, B10RL4AAB, B10TEL4AAB, E10R4AAB, E10RL4AAB 2012
B10R4INS, E10R4INS 2012
B10RL4INS, E10RL4INS 2012
B10TEL4AAA, E10TEL4AAA 2012
B10TEL4INS, E10TEL4INS 2012
B10TPL4AAA, B10TPX4AAA, E10TPL4AAA, E10TPX4AAA 2012
B10TPL4AAB, B10TPX4AAB, E10TPL4AAB, E10TPX4AAB 2012
B10TPL4INS, E10TPL4INS 2012
B10TPX4INS, E10TPX4INS 2012
B15PL4AAA, B15PL4AAB, E15PL4AAA, E15PL4AAB 2012
B15PL4INS 2012
B15R4AAA, B15RL4AAA, E15R4AAA, E15RL4AAA 2012
B15R4AAB, B15RL4AAB, B15TE4AAA, B15TE4AAB, B15TEL4AAA, B15TEL4AAB, E15R4AAB, E15RL4AAB, E15TE4AAA, E15TE4AAB, E15TEL4AAA, E15TEL4AAB 2012
B15R4INS, E15RL4INS 2012
B15RL4INS, B15TEL4INS, E15TE4INS, E15TEL4INS 2012
B15TE4INS 2012
E10EL4AAB 2012
E10EL4INS 2012
E10PL4INS 2012
E10TEL4AAB 2012
E15PL4INS 2012
E15R4INS 2012
Information:
START BY:a. remove turbocharger 1. Install the turbocharger in tool group (A). Put alignment marks on the three housings of the turbocharger for correct installation and alignment at assembly. Remove "V" clamp (2) and compressor housing (1). 2. Remove "V" clamp (3). Remove cartridge housing (5) from turbine housing (4).
When the nut that holds the compressor wheel is loosened, do not put a side force on the shaft.
3. Install tool (C) in tool (B), and put the cartridge assembly in tool (C) as shown. Use tool (D) to remove the nut that holds compressor wheel (6).
The compressor wheel can often be removed from the cartridge assembly without the use of the oil cooker. The oil cooker can be used for easier disassembly. If removal of the compressor wheel is too difficult, damage to parts can be the result.
The oil used to heat the compressor wheel must have a flash point (the temperature at which the oil will burn) above 204°C (400°F).
4. Install tool (H) on tool (E). Heat tool (E) to a temperature of 176°C 14°C (350°F 25°F). Install the cartridge assembly on tool (H) so only the compressor wheel is in the oil. Heat the compressor wheel for no more than ten minutesminutes.
Do not let the turbine wheel hit the bottom of the press during removal. Step 5 must be done before the compressor wheel cools.
5. Install tool (H) on tool (G). Put the cartridge assembly in tool (H) as shown. Remove compressor wheel (6) with an arbor press and tool (F). 6. Put the turbine wheel in tool (C). Remove seal ring (8) and shroud (7) from the shaft.7. Use tool (J) to make sure the turbocharger shaft is straight. See Special Instruction, Form No. SMHS6998. 8. Bend the tabs of the locks from bolts (10), and remove the bolts and locks.9. Remove backplate assembly (11) from the cartridge housing. Remove spacer (9) from backplate assembly (11). Remove the seal rings from spacer (9). 10. Remove the collar from behind backplate assembly (11).11. Remove thrust bearing (13) and O-ring seal (12) from the cartridge housing. 12. Remove top bearing (14) and the washer from the cartridge housing. Put a long dye mark on the top face of bearing (14). The dye marks are used for identification of the bearings when they are installed.13. Use tool (J), and remove the two rings that hold the top and bottom bearings in position. Remove the bottom bearing and washer. Put a short dye mark on the bearing. 14. Use tool (K) and remove the last ring that holds the bottom bearing in position from the cartridge housing.15. Check all the parts of the turbocharger for damage. If the parts have damage, use new parts for replacement. See Special Instruction, Form No. SMHS6854, for Turbocharger Reconditioning. Also see Guideline For Reusable Parts, Form No. SEBF8018.Assemble Turbocharger (AiResearch TW61)
1. Make sure that all of the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material.2. Put clean engine oil on all parts of the cartridge assembly.
Rings (1), (4) and (5) must be installed with the round outside edge of the rings toward the bearings.
3. Install ring (4) in the cartridge housing with tool (A).4. Install washer (3) and bearing (2) in the cartridge housing. Make sure the short dye mark on bearing (2) is up.5. Install rings (1) and (5) in the cartridge housing with tool (A).
Put 6V2055 High Vacuum Grease in the groove for seal ring (7) at assembly to one half or more of the depth of the groove all the way around.
6. Install tool (D) in tool (C). Install turbine shaft (6) in tool (D). Install seal ring (7) on turbine shaft (6) with tool (H). Install shroud (8) on turbine shaft (6).
Make sure the seal ring on turbine shaft (6) is fitted correctly in the cartridge housing.
7. Install turbine shaft (6) in the cartridge housing. 8. Install washer (12), bearing (11) with the long dye mark up, thrust washer (10) with the three lubrication grooves up and O-ring seal (9) in the cartridge housing. 9. Install the seal rings on spacer (13). Install spacer (13) in backplate assembly (15). Make sure the chamfer end of spacer (13) is toward the inside of the cartridge assembly when the backplate assembly is installed.10. Install collar (14) and backplate assembly (15) on the cartrige assembly with the oil hole in the backplate assembly in alignment with the oil hole in the cartridge housing. 11. Install the locks and bolts (16) that hold backplate assembly (15) in position. Tighten the bolts to a torque of 10.2 1.1 N m (90 10 lb.in.).
Do not put a side force on the shaft when the nut is installed or removed.
12. Install the compressor wheel as follows:a. Put the compressor wheel in position on the shaft.b. Put clean oil on the threads of the shaft and face of the nut. Install the nut, and tighten it to a torque of 1.7 N m (13 lb. in.).c. Loosen the nut, and retighten it to a torque of 3.5 N m (30 lb.in.). Mark the location of the nut, and tighten it 120° more with tool (F).d. Remove the nut, and clean the
When the nut that holds the compressor wheel is loosened, do not put a side force on the shaft.
3. Install tool (C) in tool (B), and put the cartridge assembly in tool (C) as shown. Use tool (D) to remove the nut that holds compressor wheel (6).
The compressor wheel can often be removed from the cartridge assembly without the use of the oil cooker. The oil cooker can be used for easier disassembly. If removal of the compressor wheel is too difficult, damage to parts can be the result.
The oil used to heat the compressor wheel must have a flash point (the temperature at which the oil will burn) above 204°C (400°F).
4. Install tool (H) on tool (E). Heat tool (E) to a temperature of 176°C 14°C (350°F 25°F). Install the cartridge assembly on tool (H) so only the compressor wheel is in the oil. Heat the compressor wheel for no more than ten minutesminutes.
Do not let the turbine wheel hit the bottom of the press during removal. Step 5 must be done before the compressor wheel cools.
5. Install tool (H) on tool (G). Put the cartridge assembly in tool (H) as shown. Remove compressor wheel (6) with an arbor press and tool (F). 6. Put the turbine wheel in tool (C). Remove seal ring (8) and shroud (7) from the shaft.7. Use tool (J) to make sure the turbocharger shaft is straight. See Special Instruction, Form No. SMHS6998. 8. Bend the tabs of the locks from bolts (10), and remove the bolts and locks.9. Remove backplate assembly (11) from the cartridge housing. Remove spacer (9) from backplate assembly (11). Remove the seal rings from spacer (9). 10. Remove the collar from behind backplate assembly (11).11. Remove thrust bearing (13) and O-ring seal (12) from the cartridge housing. 12. Remove top bearing (14) and the washer from the cartridge housing. Put a long dye mark on the top face of bearing (14). The dye marks are used for identification of the bearings when they are installed.13. Use tool (J), and remove the two rings that hold the top and bottom bearings in position. Remove the bottom bearing and washer. Put a short dye mark on the bearing. 14. Use tool (K) and remove the last ring that holds the bottom bearing in position from the cartridge housing.15. Check all the parts of the turbocharger for damage. If the parts have damage, use new parts for replacement. See Special Instruction, Form No. SMHS6854, for Turbocharger Reconditioning. Also see Guideline For Reusable Parts, Form No. SEBF8018.Assemble Turbocharger (AiResearch TW61)
1. Make sure that all of the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material.2. Put clean engine oil on all parts of the cartridge assembly.
Rings (1), (4) and (5) must be installed with the round outside edge of the rings toward the bearings.
3. Install ring (4) in the cartridge housing with tool (A).4. Install washer (3) and bearing (2) in the cartridge housing. Make sure the short dye mark on bearing (2) is up.5. Install rings (1) and (5) in the cartridge housing with tool (A).
Put 6V2055 High Vacuum Grease in the groove for seal ring (7) at assembly to one half or more of the depth of the groove all the way around.
6. Install tool (D) in tool (C). Install turbine shaft (6) in tool (D). Install seal ring (7) on turbine shaft (6) with tool (H). Install shroud (8) on turbine shaft (6).
Make sure the seal ring on turbine shaft (6) is fitted correctly in the cartridge housing.
7. Install turbine shaft (6) in the cartridge housing. 8. Install washer (12), bearing (11) with the long dye mark up, thrust washer (10) with the three lubrication grooves up and O-ring seal (9) in the cartridge housing. 9. Install the seal rings on spacer (13). Install spacer (13) in backplate assembly (15). Make sure the chamfer end of spacer (13) is toward the inside of the cartridge assembly when the backplate assembly is installed.10. Install collar (14) and backplate assembly (15) on the cartrige assembly with the oil hole in the backplate assembly in alignment with the oil hole in the cartridge housing. 11. Install the locks and bolts (16) that hold backplate assembly (15) in position. Tighten the bolts to a torque of 10.2 1.1 N m (90 10 lb.in.).
Do not put a side force on the shaft when the nut is installed or removed.
12. Install the compressor wheel as follows:a. Put the compressor wheel in position on the shaft.b. Put clean oil on the threads of the shaft and face of the nut. Install the nut, and tighten it to a torque of 1.7 N m (13 lb. in.).c. Loosen the nut, and retighten it to a torque of 3.5 N m (30 lb.in.). Mark the location of the nut, and tighten it 120° more with tool (F).d. Remove the nut, and clean the
Parts screw EVINRUDE:
0125308
0125308 SCREW, Bezel mounting
B10EL4AAA, B10EL4AAB, B10PL4AAA, B10PL4AAB, B10R4AAA, B10R4AAB, B10TEL4AAA, B10TPL4AAA, B10TPL4AAB, B15PL4AAA, B15R4AAA, B15R4AAB, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE250CXECB, BE250CXEDA, BE250CXEUM, BE40EECR, BE4
5041598
5041598 *Screw
B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15R4AAA, B15R4AAB, B4R4AAA, B4R4INS, B6R4AAA, B6R4INS, E10TEL4AAB
5041637
5041637 Screw
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B4R4AAA, B4R4INS, B6R4AAA, B6R4INS, E10EL4AAB, E10EL4INS, E1
5041618
5041618 SCREW
B10EL4AAA, B10EL4INS, B10PL4AAA, B10PL4INS, B10PX4INS, B10R4AAA, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4INS, B10TPX4INS, E10EL4INS, E10PL4INS
5041609
5041609 SCREW
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, E10EL4AAB, E10EL4INS, E10PL4INS, E10TEL4AAB
5041606
5041606 SCREW
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
5041605
5041605 SCREW
B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, E10TEL4AAB
5041603
5041603 SCREW
B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4INS, B15TE4INS, E10TEL4AAB, E15PL4INS, E15R4INS