0206523 EVINRUDE SEAL, Motor cover upper


0206523 SEAL, Motor cover upper EVINRUDE 50172S, 50202C, 50442M, 50542B, 55642E SEAL
0206523 SEAL, Motor cover upper EVINRUDE
Rating:
83

Buy SEAL, Motor cover upper 0206523 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

50172S, 50173S 1971
50202C, 50203C, 50272C, 50273C 1972
50442M, 50443M, 50472M, 50473M 1974
50542B, 50543B, 50572B, 50573B 1975
55642E, 55643E, 55672E, 55673E 1976

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A - Drill Bit (3 mm) 1
B 1U-7600 Slide Hammer Puller 1
C 1U-7262 Telescopic Magnet 1 Start By:
Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install" for the correct procedure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02927001
Apply clean grease to Tooling (A) to prevent any swarf that is generated from entering the engine. Use Tooling (A) to drill three evenly spaced holes in crankshaft front seal (1).
Use Tooling (B) with care to remove crankshaft front seal (1) from front cover (3) and crankshaft pulley adaptor (2). Alternate the position of Tooling (B) from one hole to another. Alternating the position of Tooling (B) will allow the crankshaft front seal to be easily removed from the crankshaft.
Use Tooling (C) to collect any swarf that has entered the engine.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
D(1) 460-8232 Crankshaft Front Seal Installer 1
D(2) 390-1125 Crankshaft Front Seal Installer 1
(1) Used for Procedure 1
(2) Used for Procedure 2Note: The tool used is determined by which crankshaft front seal is installed.Procedure 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft pulley adaptor and the front cover are clean and free from oil and damage.
Illustration 2 g02927218
Sectional view of the crankshaft front seal, the crankshaft pulley adaptor, and the installation tool
Use Tooling (D) and follow Step 2.a through Step 2.f to install crankshaft front seal (1).
Position the adaptor of Tooling (D) onto the crankshaft pulley adaptor and secure with bolts.
Position the new crankshaft front seal (1) over the adaptor onto the front of the crankshaft.
Align the seal installer of Tooling (D) with the crankshaft.Note: Check that the installer of Tooling (D) is parallel to the adaptor.
Install the nut and washer to the locator.
Tighten the nut until the installer bottoms out on the adaptor to install crankshaft front seal (1) into front cover (3) and onto crankshaft pulley adaptor (2).
Remove Tooling (D).End By:
Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install" for the correct procedure.Procedure 2
Ensure that the crankshaft pulley adaptor and the front cover are clean and free from oil and damage.
Illustration 3 g06128680
Sectional view of the crankshaft front seal, the crankshaft pulley adaptor, and the installation tool
Use Tooling (D) and follow Step 2.a through Step 2.d to install crankshaft front seal (1).
Position the new crankshaft front seal (1) over the nose of the crankshaft into the recess in the front cover.
Align Tooling (D) with the crankshaft and crankshaft front seal (1).
Use a suitable tool to drive (D) and the new crankshaft front seal (1) into position.
Remove Tooling (D).End By:
Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install" for the correct procedure.


Parts seal EVINRUDE:

0313507
SEAL,Upper
0313507 SEAL,Upper
100193A, 100293R, 100882B, 115083D, 115983E, 125183C, 125283R, 40404S, 40504C, 50172S, 50202C, 50302R, 50442M, 50542B, 55872A, 55972A, 60072B, 60172C, 65272S, 65372R, 65832B, 70442M, 70572B, 75542B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0310058
SEAL, Thermostat
0310058 SEAL, Thermostat
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 150840S, 150940C, 15404G, 15504C, 15604A, 175740S, 18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 200640S, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25902B, 35602G, 50172S, 50202C
0313398
SEAL BEARING HEAD
0313398 SEAL BEARING HEAD
40404S, 40504C, 50172S, 50202C, 50302R, 50442M, 50542B, 55872A, 55972A, 60072B, 60172C, 65272S, 65372R, 70442M, 70572B, 75542B, E20CRCEM, E25RCEM, E30RCED, E35RCED
0305762
 
0305762 SEAL, Impeller hsg.cover
50302R, 50442M, 50542B, 50902C, 55642E, 55772D, 55874S, 55972A, 60072B, 60172C, 65372R, 65832B, 70442M, 70572B, 70773S, 70873C, 70973R, 75542B, 75642D, 85852A, 85892A, E35AELCDE, E35AELCUD, E40AELCCS, E40ECDE, E40ECOB, E40ECRM, E40ECUD, E40WREES, E40
0315795
 
0315795 SEAL, Upper
50172S, 50202C
0315956
SEAL, Lower to outer housing
0315956 SEAL, Lower to outer housing
50172S, 50202C, 50302R, 50442M, 50542B, 50902C, 55642E, 55772D, 55874S, E35AELCDE, E35AELCUD, E40AELCCS, E40ECDE, E40ECOB, E40ECRM, E40ECUD, E40WREES, E40WRLSIR, E40WRLSSC, E45RCCDS, E45RCCUC, E45RCE, E45RCEIA, E45RCENM, E45RCEOD, E45RCERE, E45RCESR,
0317776
 
0317776 SEAL
100293R, 125283R, 50302R, 50442M, 50542B, 50902C, 55642E, 55772D, 55874S, 65272S, 65372R, 70442M, 70572B, 70773S, 70873C, 70973R, 75542B, 75642D, 85293R, E35AELCDE, E35AELCUD, E40AELCCS, E40DELSDA, E40DELSOR, E40DELSRC, E40DPLAAA, E40DPLABA, E40DPLII
Back to top