0313691 EVINRUDE SEAL, Lower


0313691 SEAL, Lower EVINRUDE 100193A, 115083D, 115983E, 125183C, 55872A, 55972A, 60072B, 60172C, 85093B, 85193A, 85993E SEAL
0313691 SEAL, Lower EVINRUDE
Rating:
68

Buy SEAL, Lower 0313691 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

BRP EVINRUDE entire parts catalog list:

100193A, 100193C 1971
115083D 1970
115983E, 115983S 1969
125183C 1971
55872A, 55872R, 55872S, 55873A, 55873R, 55873S 1968
55972A, 55972C, 55973A, 55973C 1969
60072B, 60072D, 60073B, 60073D 1970
60172C, 60172E, 60173C, 60173E 1971
85093B, 85093D 1970
85193A, 85193H 1971
85993E, 85993M, 85993S 1969

Information:

White Smoke: Recommended Procedure
1. Cold Outside Temperatures - When the air outside is cold, the cylinder temperature is cooler. Not all the fuel will burn in the cylinders. The fuel which does not burn comes out the exhaust as white smoke. White smoke is normal in cold temperatures until the engine operates long enough to become warm. There will be less white smoke if No. 1 diesel fuel is used.2. Long Idle Periods - When an engine runs at idle speed for a long period of time, the cylinders cool and all of the fuel does not burn. Do not idle an engine for a long period of time. Stop an engine when it is not in use. If long idle periods are necessary use No. 1 diesel fuel.3. Low Quality Fuel - Test the engine with fuel according to recommendations by Caterpillar Tractor Co.4. Air in Fuel System - With air in the fuel system the engine will normally be difficult to start, run rough and release a large amount of white smoke. To remove the air from the fuel system open the manual bleed valve on the fuel injection pump housing. Operate the priming pump until the flow of fuel from the manual bleed valve is free of air. Close the manual bleed valve and fasten the fuel priming pump. Start the engine. If the engine still does not run smooth or releases a large amount of white smoke, loosen the fuel line nuts one at a time at the cylinder heads, and permit the fuel to come out until it is free of air. Tighten the fuel line nuts. If air is not removed in this way, put 5 psi (35 kPa) [CAUTION do not use more than 8 psi (55 kPa)] of air pressure to the fuel tank and check for leaks at connections between the fuel tank and the fuel transfer pump. If there are no leaks at the connections, remove the fuel supply line from the tank and connect it to an outside fuel supply. If this corrects the problem in the suction line (standpipe) inside the fuel tank has a leak.5. Fuel Injection Timing Not Correct - Check and make necessary adjustments as per Testing and Adjusting section of this Service Manual.6. Automatic Timing Advance Does Not Operate Correctly - Check with engine warm. Use the 1P3500 Timing Light Group. Special Instruction (GMG00501) gives the test procedure. If the timing light is not available, make rapid "acceleration" (increase in speed) from low idle to high idle. Engine must have smooth acceleration. A timing advance that does not operate correctly can cause delays of the engine acceleration at some rpm before high idle, or possibly cause the engine to run rough and have exhaust noise (backfire) during acceleration. This condition is difficult to find if engine acceleration is slow or at a constant engine rpm.7. Valve Adjustment Not Correct - Check and make necessary adjustments as per Testing and Adjusting section of this Service Manual. Intake valve adjustment is .015 in. (0.38 mm) and exhaust valve adjustment is .025 in. (0.64 mm).8. Bad Fuel Nozzle(s) - Bad fuel nozzles will normally cause the engine to "misfire" (ignition not regular) and run rough, but can cause too much smoke and the engine still be running smooth. Remove the fuel nozzles and test as per Testing and Adjusting section of this Service Manual.9. Misfiring Cylinders(s) - See the chart Misfiring And Running Rough.Blue Smoke
10. Engine Oil Level Too High - Do not put too much oil in the crankcase. If the oil level in the crankcase goes up as the engine is used, check for fuel in the crankcase. See the chart FUEL IN CRANKCASE OIL.11. Damage to Positive Crankcase Ventilator Valve or Valve Assembled Wrong - The positive crankcase ventilator valve must be assembled correctly and the diaphragm and/or gasket must be free of damage.12. Worn Valve Guides - See the Specifications section of this Service Manual for the maximum permissible wear of the valve guides. The repair procedure for valve guides is in the Reconditioning Procedures section of this Service Manual.13. Worn Piston Rings and/or Cylinder Walls - Worn piston rings and/or cylinder walls can be the cause of blue smoke and can cause a loss of compression. Check cylinder condition with the cylinder leakage tester. Special Instruction (GMG00694) gives the test procedure. Make a visual inspection of the cylinder walls and piston rings. If necessary measure the cylinder walls and piston rings. For the cylinder and piston ring specifications see the Specification section of this Service Manual. High wear at low mileage is normally caused by dirt coming into the engine with the inlet air.14. Wear or Damage to Pistons - Check piston ring to groove clearance. Pistons which have worn grooves and pistons with damage or defects can cause blue smoke and too much oil consumption. Make sure the oil return holes under the oil ring are open.


Parts seal EVINRUDE:

0313507
SEAL,Upper
0313507 SEAL,Upper
100193A, 100293R, 100882B, 115083D, 115983E, 125183C, 125283R, 40404S, 40504C, 50172S, 50202C, 50302R, 50442M, 50542B, 55872A, 55972A, 60072B, 60172C, 65272S, 65372R, 65832B, 70442M, 70572B, 75542B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0303804
SEAL,Pivot shaft
0303804 SEAL,Pivot shaft
100193A, 100293R, 100882B, 115083D, 115983E, 125183C, 125283R, 50542B, 65832B, 75542B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0310599
SEAL,Propeller shaft
0310599 SEAL,Propeller shaft
100882B, 115083D, 115983E, 55872A, 55972A, 60072B, 60172C, 85093B, 85993E
0313398
SEAL BEARING HEAD
0313398 SEAL BEARING HEAD
40404S, 40504C, 50172S, 50202C, 50302R, 50442M, 50542B, 55872A, 55972A, 60072B, 60172C, 65272S, 65372R, 70442M, 70572B, 75542B, E20CRCEM, E25RCEM, E30RCED, E35RCED
0313392
0315116
 
0315116 SEAL, Cover
100193A, 115083D, 115983E, 125183C, 85093B, 85193A, 85993E
0314937
 
0314937 SEAL, Gearcase to exhaust housing inner
100193A, 100293R, 115083D, 115393M, 115493B, 115593, 115693D, 115793S, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 85093B, 85193A, 85293R, 85393M, 85493B, 85593E, 85693D, 85993E
0315403
SEAL, Valve housing
0315403 SEAL, Valve housing
100193A, 100293R, 115083D, 115393M, 115493B, 115593, 115793S, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 85093B, 85193A, 85293R, 85393M, 85493B, 85593E, 85993E
Back to top