0330731 SEAL, Engine cover EVINRUDE
E120TLCCA, E120TLCDC, E120TLCOS, E120TLCUR, E140CXCCS, E140TLCDC, E140TLCOS, E140TLCUA, E200CXCCR, E200STLCDR, E200STLCUA, E225CLCUB, E225CXCCE, E225PTLCDA
SEAL

Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- ENGINE COVER - JOHNSON » 0330731
E120TLCOS, E120TXCOS 1985
E120TLCUR, E120TXCUR 1987
E140CXCCS, E140TLCCM, E140TXCCM 1988
E140TLCDC, E140TXCDC 1986
E140TLCOS, E140TXCOS 1985
E140TLCUA, E140TXCUA 1987
E200CXCCR, E200STLCCM, E200TXCCR 1988
E200STLCDR, E200TXCDS 1986
E200STLCUA, E200TXCUC 1987
E225CLCUB, E225CXCUB, E225PLCUB, E225PXCUB, E225TLCUB, E225TXCUB 1987
E225CXCCE, E225PLCCE, E225PXCCE, E225TLCCE, E225TXCCE 1988
E225PTLCDA, E225PTXCDA, E225TLCDA, E225TXCDA 1986
Information:
Illustration 1 g03029438
Schematic for the compression brake circuit
Probable Causes
Codes
Short circuit
Open circuitRecommended Actions
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Turn the keyswitch to ON.
C. Access the diagnostic overrides under the "Diagnostics" menu.
D. Start the "Compression Brake Low/High Override".
E. Once Cat ET displays the status of the compression brake solenoid, stop the "Compression Brake Low/High Override".
F. Monitor the "Active Diagnostic Code" screen on Cat ET. Record any active diagnostic codes.
G. Start the "Compression Brake Med/High Override".
H. Once Cat ET displays the status of the compression brake solenoid, stop the "Compression Brake Med/High Override".
I. Monitor the "Active Diagnostic Code" screen on Cat ET. Record any active diagnostic codes.
Codes
Result: A 791-5, or 792-5 diagnostic code is active.
Proceed to Test Step 2.
Result: A 791-6, or 792-6 diagnostic code is active.
Proceed to Test Step 4.
2. Create a Short Between the Wires of the Suspect Compression Brake Solenoid at the Valve Cover Connector
Note: To troubleshoot a 791-5 diagnostic code, use the "Compression Brake Low/High Override" in Cat ET. To troubleshoot a 792-5 diagnostic code, use the "Compression Brake Med/High Override" in Cat ET.
A. Turn the keyswitch to OFF.
B. Disconnect the harness at the valve cover connector.
C. Fabricate a jumper wire to create a short between the supply wire for the suspect compression brake solenoid and engine ground.
D. Turn the keyswitch to ON.
E. Access the diagnostic overrides under the "Diagnostics" menu.
F. Start the override for the compression brake.
G. Once Cat ET displays the status of the compression brake solenoid, stop the override.
H. Monitor the "Active Diagnostic Code" screen in Cat ET. Record any active diagnostic codes.
I. Turn the keyswitch to OFF. Remove the jumper wire.
Note: A -5 open circuit diagnostic code will be active for the other compression brake solenoid. Ignore the diagnostic codes for the other compression brake solenoid. Ignore any diagnostic codes for the injector solenoids.
Short circuit
Result: A 791-6, or 792-6 diagnostic code is active. The harness wiring is OK.
Proceed to Test Step 3.
Result: A 791-5, or 792-5 diagnostic code is active.
Repair: Repair the harness or replace the harness.
If the problem is not resolved, proceed to Test Step 3.
3. Create a Short Circuit at the Compression Brake Solenoid
Note: Two solenoids are activated to create a medium braking action. The open could be in either solenoid or in the harness. To isolate the problem for a medium braking action, run this test step for each of the solenoids. The short must be created separately at each solenoid.
Note: To troubleshoot a 791-5 diagnostic code, use the "Compression Brake Low/High Override" on Cat ET. To troubleshoot a 792-5 diagnostic code, use the "Compression Brake Med/High Override" on Cat ET.
A. Turn the keyswitch to OFF.
B. Remove the valve cover.
C. Reconnect the valve cover connector.
D. Disconnect the connector on the suspect compression brake solenoid.
E. Inspect the terminals on the connector for the compression brake solenoid for damage.
F. Fabricate a jumper wire to short the two wires for the suspect solenoid on the solenoid connector. Crimp a pin to each end of the jumper wire.
G. Make sure that the solenoid connector securely holds the jumper wire.
Note: Worn terminals and/or damaged terminals on the solenoid connector could cause an intermittent "Open".
H. Turn the keyswitch to ON.
I. Access the diagnostic override under the "Diagnostics" menu.
J. Start the override for the compression brake.
K. Once Cat ET displays the status of the compression brake solenoid, stop the override.
L. Monitor the "Active Diagnostic Code" screen on Cat ET. Record any active diagnostic codes.
M. Turn the keyswitch to OFF. Remove the jumper wire.
Short circuit
Result: A 791-6 or a 792-6 diagnostic code is active. The harness wiring between the connector for the compression brake solenoid and the ECM is OK.
Repair: Replace the suspect compression brake solenoid. Verify that the problem is resolved.
Result: A 791-5 or a 792-5 diagnostic code is active.
Repair: Repair the harness or replace the harness between the connector for the compression brake solenoid and the valve cover connector.
If the problem is not resolved, proceed to Test Step 4.
4. Create an Open Between the Wires of the Suspect Compression Brake Solenoid at the Valve Cover Connector
Note: To troubleshoot a 791-6 diagnostic code, use the "Compression Brake Low/High Override" on Cat ET. To troubleshoot a 792-6 diagnostic code, use the "Compression Brake Med/High Override" on Cat ET.
A. Turn the keyswitch to OFF.
B. Disconnect the harness at the valve cover connector.
C. Turn the keyswitch to ON.
D. Access the diagnostic override under the "Diagnostics" menu.
E. Start the override for the compression brake.
F. Once Cat ET displays the status of the compression brake solenoid, stop the override.
G. Monitor the Active Diagnostic Code screen on Cat ET. Record any active diagnostic codes.
H. Turn the keyswitch to OFF. Remove the wire short.
I. Reconnect the valve cover connector.
Open circuit detected
Result: A 791-5 or a 792-5 diagnostic code is active. The harness wiring between the valve cover connector and the ECM is OK.
Proceed to Test Step 5.
Result: A 791-6 or a 792-6 diagnostic code is active.
Repair: Repair the harness or replace the harness between the P2 connector and the valve cover connector.
If the problem is not resolved, proceed to Test Step 5.
5. Create an Open Circuit at the Compression Brake Solenoid
Note: Two solenoids are activated to create a medium braking action. The short could be in either solenoid or in the harness. To isolate the problem for a medium braking action, run this test step for each of the solenoids. The open must be created separately at each solenoid.
Note: To troubleshoot a 791-6 diagnostic code, use the "Compression Brake Low/High Override" on Cat ET. To troubleshoot a 792-6 diagnostic code, use the "Compression Brake Med/
Parts seal EVINRUDE:
0321008
0321008 SEAL,Shift rod to housing
100990S, 115790S, 115890C, 150840S, 175740S, 200640S, 70873C, BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXE
0322575
0322575 SEAL,Upper
100990S, 115790S, 115793S, 115890C, 150840S, 150940C, 175740S, C155WTLM, CE275TLCDC, CE275TLCOS, CE300TLCDC, CE300TLCOS, E100MLCSC, E100STLCCA, E100STLCEM, E100STLEIE, E100STLEND, E100STLESB, E100WMLCDR, E100WMLCOC, E100WMLCRS, E100WTLCUA, E100WTLEIB
0330137
0330137 SEAL
BE115ELEDR, BE25ARECA, BE25AREDC, BE25AREUR, BE35ARECR, BE35AREDS, BE35AREEA, BE35AREUC, BE35ARSIB, BE35ARSSM, BE50DTLEDC, BE60ELEDR, BE70ELEDA, BE90ELEDR, E100FPLSOC, E100FPLSRS, E100STLCCA, E100STLCEM, E100STLEIE, E100STLEND, E100STLERC, E100STLESB
0124369
0124369 SEAL, Filter
BE115ELEDR, BE115ELEUA, BE115GLECM, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE25AREDC, BE25AREUR, BE35AREDS, BE35AREUC, BE50DTLEDC, BE60ELEDR, BE70ELEDA, BE8RCB, BE8RCH, BE8RCLT, BE90ELEDR, BE90ELEUA, BE90SLECM, C155WT
0328650
0328650 SEAL, Carb. body
CE275TLCOS, CE300TLCOS, E120TLCDC, E120TLCOS, E120TLCUR, E140TLCDC, E140TLCOS, E140TLCUA, E185ESXENR, E185ESXESS, E185ESXETA, E185ESXW, E200CXATF, E200CXCCR, E200CXCEA, E200CXEIB, E200CXENE, E200CXESM, E200STLCDR, E200STLCUA, E225CLCUB, E225CXATF, E2
0331098
0331098 SEAL, Baffle to carb.
CE275TLCDC, CE275TLCOS, CE300TLCDC, CE300TLCOS, E120TLCCA, E120TLCDC, E120TLCEM, E120TLCOS, E120TLCUR, E120TLEIE, E120TLEND, E120TLESB, E120TLETF, E125ESXENR, E125ESXESS, E125ESXETA, E125ESXW, E140CXATF, E140CXCCS, E140CXCEC, E140CXEIA, E140CXENM, E1
0330938
0330938 SEAL, Engine cover, front
E120TLCCA, E120TLCDC, E120TLCOS, E120TLCUR, E125ESXW, E140CXCCS, E140TLCDC, E140TLCOS, E140TLCUA
0332584
0332584 SEAL, Pivot pin
B25JREUR, BE10EEDD, BE10FAEDC, BE10FAEUR, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE115GLECM, BE115TLEDA, BE130TLECE, BE150ELECD, BE15EEDS, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE15RELEUC, BE175EXECD, BE200CXECM, BE20SEECB, BE20SEEDA, BE20SEEUM,