0378427 EVINRUDE SEAL RING SET


0378427 SEAL RING SET EVINRUDE 65832B, 85852A, 85892A SEAL
0378427 SEAL RING SET EVINRUDE
Rating:
93

Buy SEAL RING SET 0378427 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 9
 

Compatible models:

65832B   85852A   85892A   EVINRUDE

BRP EVINRUDE entire parts catalog list:

65832B, 65833B, 65852B, 65853B 1968
85852A, 85853A 1968
85892A, 85893A 1968

Information:

Start By:a. disassemble governorb. remove fuel injection pumps
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Remove cover (1) and gasket. 2. Remove rack (2).
If the original lifters are to be installed in the fuel injection pump housing, put identification marks on them as to their location in the housing.
3. Remove lifters (3). 4. Put the fuel injection pump housing on end on blocks. Use tool (A) to remove snap ring (4). 5. Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump housing to loosen washer (5). Remove washer (5). 6. Remove camshaft (6). 7. Remove bearings (7) from the drive end of the fuel injection pump housing. 8. Remove bearings (8) from the governor end of the fuel injection pump housing.Assemble Fuel Injection Pump Housing
Be sure all oil passages are clear, and put clean oil on all parts before assembly. 1. Use tooling (B) to install bearing (10) in the governor end of the fuel injection pump housing with junction (joint) (11) toward the top of the fuel injection pump housing. Install the bearing so it is 0.25 0.20 mm (0.10 0.008 in) below the surface of the housing.2. Use tooling (B) to install bearing (9) in the governor end of the fuel injection pump housing so it is 7.16 0.13 mm (0.282 0.005 in) below the surface of the housing. 3. Use tooling (B) to install bearing (12) in the drive end of the fuel injection pump housing with the junction (joint) in the bearing toward the top of the fuel injection pump housing. Install the bearing so it is 1.00 0.25 mm (9.039 0.010 in) below the surface of the housing. 4. Install plate (13) of tooling (C) on the drive end of the fuel injection pump housing to install the bearing for the rack. Use clean grease to hold the new rack bearing on driver (14) of tooling (C). Install the driver and bearing in plate (13) with the groove in the driver in alignment with the pin in the plate and use a hammer to push the bearing into position. The bearing will be installed to the correct depth when the shoulder of the driver is against plate (13).5. Remove tooling (C) from the fuel injection pump housing. The rack bearing must be installed so it is 0.25 0.25 mm (0.010 0.010 in) below the surface of the housing. 6. Install camshaft (6).7. Put the fuel injection pump housing on end, and place a block under the camshaft. 8. Put washer (5) over the end of the camshaft and use tooling (B) and a spacer (15) that has an inside diameter of 38.1 mm (1.5 in) and a length of 31.75 mm (1.25 in) to push the washer against its seat on the camshaft. Camshaft must have 0.285 0.235 mm (0.0112 0.0093 in) end play when washer is pushed against cam shoulder. 9. Use tool (A) to install snap ring (4). 10. Install six lifters (3) in the fuel injection pump housing with the groove in the lifter in alignment with the pin in the housing. 11. Install rack (2) with the groove in the end of the rack in alignment with the ear (tab) of the rack bearing, at the drive end of the fuel injection pump housing. The six lifters are all the same and can be mixed. 12. Install the gasket and cover (1).End By:a. assemble governorb. install fuel injection pumps


Parts seal EVINRUDE:

0313507
SEAL,Upper
0313507 SEAL,Upper
100193A, 100293R, 100882B, 115083D, 115983E, 125183C, 125283R, 40404S, 40504C, 50172S, 50202C, 50302R, 50442M, 50542B, 55872A, 55972A, 60072B, 60172C, 65272S, 65372R, 65832B, 70442M, 70572B, 75542B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0305119
SEAL,Lower bearing
0305119 SEAL,Lower bearing
100882B, 65832B, 85852A, 85892A
0305851
 
0305851 SEAL,Motor to crankcase
100882B, 85852A, 85892A
0303804
SEAL,Pivot shaft
0303804 SEAL,Pivot shaft
100193A, 100293R, 100882B, 115083D, 115983E, 125183C, 125283R, 50542B, 65832B, 75542B, 85093B, 85193A, 85293R, 85852A, 85892A, 85993E
0310741
 
0310741 SEAL,Housing to cover
100882B, 65832B, 85852A, 85892A
0205605
0206190
0206021
Back to top