5032124 EVINRUDE *SEAL, Starter Assy. - Z


5032124 *SEAL, Starter Assy. - Z EVINRUDE E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS SEAL
5032124 *SEAL, Starter Assy. - Z EVINRUDE
Rating:
38

Buy *SEAL, Starter Assy. - Z 5032124 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$41.43
 

24-09-2020
4.40924524[1.80] Pounds
-: -
Connected Essentials 5032124 Tailored Heavy Duty Custom Fit Car Mats, for C Class Auto (2007-2010), Grey with Blue Trim, Premium
Complete set of 4 tailored custom fit car mats - designed and manufactured specifically for Mercedes C Class Auto (2007-2010) || Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
Number on catalog scheme: 8
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E25EL4SIC, E25PL4SIC, E25R4SIC, E25RL4SIC, E25TE4SIC, E25TEL4SIC 2001
E25EL4SSS, E25PL4SSS, E25R4SSS, E25RL4SSS, E25TE4SSS, E25TEL4SSS 2000
E30EL4SIC, E30PL4SIC, E30R4SIC, E30RL4SIC, E30TE4SIC, E30TEL4SIC 2001
E30EL4SSS, E30PL4SSS, E30R4SSS, E30RL4SSS, E30TE4SSS, E30TEL4SSS 2000

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
B 298-5564 T40 Torx Socket 1
D 1U-5718 Vacuum Pump 1
169-7372 Fluid Sampling Bottle 1
4C-4057 Tube
7.9 mm (0.31 inch) Outside Diameter 1
E 276-1216 Injector Pipe Nut Tool 1
F 247-5377 Torque Wrench 1
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Use a deep socket to install the electrical connections from the electronic unit injectors. Use of incorrect tooling will result in damage to the electronic unit injectors.
Illustration 1 g01772353
Typical calibration code
If a replacement electronic unit injector is installed, the correct trim file for the injector must be programmed into the electronic control module. Refer to Troubleshooting, "Injector Trim File" for more information. The code that is required to obtain the trim file for the injector is at Position (X).Note: Record Code (X) before the electronic unit injector is installed.
Use Tooling (D) to remove any fuel from the cylinder.Note: Evacuate as much fuel as possible from the cylinder before installing the electronic unit injector.
Ensure that the fuel inlet port of the electronic unit injector is capped. Ensure that the electronic unit injector is clean.
Illustration 2 g01769574
Typical example
On installing an original electronic unit injector, install a new O-ring seal (16) and sealing washer (15) to electronic unit injector (12).Ensure that O-ring seal (16) and sealing washer (15) on a new electronic unit injector are not damaged and in place.Note: Do not lubricate the O-ring seal.
Ensure that the seat for the electronic unit injector in the cylinder head is clean and free from damage. Ensure that the old sealing washer has been removed from the cylinder head.
Illustration 3 g01769513
The rocker shaft is not shown for clarity.
Position clamp (14) between the rocker arm and the valve springs. Align electronic unit injector (12) to the bore for the electronic unit injector in the cylinder head. Install the clamp to the electronic unit injector. Ensure that the electronic unit injector is pushed firmly against the seat in the cylinder head.
Install a new torx screw (13) to clamp (14). Tighten the torx screw finger tight.
Remove the cap from electronic unit injector (12). Install a new seal (9) to electronic unit injector (12) and to the valve mechanism cover base. Ensure that the flange on the seal is flush with the valve mechanism cover base.
Remove the plugs from the new fuel injection line. Loosely install the fuel injection line. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install".Note: Ensure that the ends of the fuel injection line are seated in the electronic unit injector and the fuel manifold. Tighten the nuts finger tight.
Use Tooling (B) to tighten torx screw (13) to a torque of 27 N m (239 lb in).Note: Tooling (B) must be used to ensure no damage to the rocker arms.
Tighten the clamps and the fuel injection lines. Use Tooling (E) to tighten the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install" for more information.
Illustration 4 g01772534
Typical example
Illustration 5 g01774093
Typical example
The electronic unit injector is not shown for clarity.


Parts seal EVINRUDE:

5031269
 
5031269 SEAL, Oil
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC
5031973
SEAL, Air silencer
5031973 SEAL, Air silencer
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031959
 
5031959 SEAL, Valve spring
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031892
 
5031892 SEAL, Oil, upper
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031893
 
5031893 *SEAL
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5032112
 
5032112 *SEAL, Upper cover
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031891
*SEAL
5031891 *SEAL
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5032114
 
5032114 SEAL, Side cover
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
Back to top