0582153 EVINRUDE SENDING UNIT ASSY.


0582153 SENDING UNIT ASSY. EVINRUDE E100MLCSC, E115MLCIH, E115MLCNB, E115MLCSA, E115MLCTE, E140MLCIH, E140MLCNB, E140MLCSA, E140MLCTE, E150STLCTE, E150TRLCIA, E150TRLCNM, E150TRLCSF, E150TRLCTB, E175TRLCIM, E175TRLCNB, E175TRLCSA, E175TRLCTD, E200TRLCIB, E200TRLCNE, E200TRLCSF, E200TRL SENDING
0582153 SENDING UNIT ASSY. EVINRUDE
Rating:
38

Buy SENDING UNIT ASSY. 0582153 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 84
 

BRP EVINRUDE entire parts catalog list:

E100MLCSC, E100TLCSC, E100TXCSC 1980
E115MLCIH, E115MLCIM, E115TLCIH, E115TLCIM, E115TXCIH, E115TXCIM 1981
E115MLCNB, E115TLCNB, E115TXCNB 1982
E115MLCSA, E115TLCSA, E115TXCSA 1980
E115MLCTE, E115TLCTE, E115TXCTE 1983
E140MLCIH, E140MLCIM, E140TRLCIH, E140TRLCIM, E140TRXCIH, E140TRXCIM 1981
E140MLCNB, E140TRLCNB, E140TRXCNB 1982
E140MLCSA, E140TRLCSA, E140TRXCSA 1980
E140MLCTE, E140TRLCTE, E140TRXCTE 1983
E150STLCTE 1983
E150TRLCIA, E150TRLCIH, E150TRXCIA, E150TRXCIH 1981
E150TRLCNM, E150TRXCNM 1982
E150TRLCSF, E150TRLCSR, E150TRXCSF, E150TRXCSR 1980
E150TRLCTB, E150TRLCTE, E150TRXCTB, E150TRXCTE 1983
E175TRLCIM, E175TRXCIH, E175TRXCIM 1981
E175TRLCNB, E175TRXCNB 1982
E175TRLCSA, E175TRLCSF, E175TRXCSA, E175TRXCSF 1980
E175TRLCTD, E175TRLCTE, E175TRXCTD, E175TRXCTE 1983
E200TRLCIB, E200TRLCIH, E200TRXCIB, E200TRXCIH 1981
E200TRLCNE, E200TRXCNE 1982
E200TRLCSF, E200TRLCSM, E200TRXCSF, E200TRXCSM 1980
E200TRLCTD, E200TRLCTS, E200TRXCTD, E200TRXCTS 1983
E235STLCTS 1983
E235TRLCIB, E235TRLCIH, E235TRXCIB, E235TRXCIH 1981
E235TRLCNE, E235TRXCNE 1982
E235TRLCSM, E235TRXCSM 1980
E235TRLCTD, E235TRLCTS, E235TRXCTD, E235TRXCTS 1983
E70ELCIH, E70ELCIM, E70TLCIM 1981
E70ELCNB, E70TLCNB 1982
E70ELCSA 1980
E70ELCTE, E70TLCTE 1983
E75ERCIH, E75ERCIM, E75ERLCIH, E75ERLCIM, E75TRLCIH, E75TRLCIM 1981
E75ERCNB, E75ERLCNB, E75TRLCNB 1982
E75ERCSA, E75ERLCSA, E75TRLCSA 1980
E75ERCTE, E75ERLCTE, E75TRLCTE 1983
E85MLCSA, E85STLCSA, E85STXCSA 1980
E90MLCIH, E90MLCIM, E90TLCIH, E90TLCIM, E90TXCIH, E90TXCIM 1981
E90MLCNB, E90TLCNB, E90TXCNB 1982
E90MLCTE, E90TLCTE, E90TXCTE 1983

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
B 298-5564 T40 Torx Socket 1
D 1U-5718 Vacuum Pump 1
169-7372 Fluid Sampling Bottle 1
4C-4057 Tube
7.9 mm (0.31 inch) Outside Diameter 1
E 276-1216 Injector Pipe Nut Tool 1
F 247-5377 Torque Wrench 1
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Use a deep socket to install the electrical connections from the electronic unit injectors. Use of incorrect tooling will result in damage to the electronic unit injectors.
Illustration 1 g01772353
Typical calibration code
If a replacement electronic unit injector is installed, the correct trim file for the injector must be programmed into the electronic control module. Refer to Troubleshooting, "Injector Trim File" for more information. The code that is required to obtain the trim file for the injector is at Position (X).Note: Record Code (X) before the electronic unit injector is installed.
Use Tooling (D) to remove any fuel from the cylinder.Note: Evacuate as much fuel as possible from the cylinder before installing the electronic unit injector.
Ensure that the fuel inlet port of the electronic unit injector is capped. Ensure that the electronic unit injector is clean.
Illustration 2 g01769574
Typical example
On installing an original electronic unit injector, install a new O-ring seal (16) and sealing washer (15) to electronic unit injector (12).Ensure that O-ring seal (16) and sealing washer (15) on a new electronic unit injector are not damaged and in place.Note: Do not lubricate the O-ring seal.
Ensure that the seat for the electronic unit injector in the cylinder head is clean and free from damage. Ensure that the old sealing washer has been removed from the cylinder head.
Illustration 3 g01769513
The rocker shaft is not shown for clarity.
Position clamp (14) between the rocker arm and the valve springs. Align electronic unit injector (12) to the bore for the electronic unit injector in the cylinder head. Install the clamp to the electronic unit injector. Ensure that the electronic unit injector is pushed firmly against the seat in the cylinder head.
Install a new torx screw (13) to clamp (14). Tighten the torx screw finger tight.
Remove the cap from electronic unit injector (12). Install a new seal (9) to electronic unit injector (12) and to the valve mechanism cover base. Ensure that the flange on the seal is flush with the valve mechanism cover base.
Remove the plugs from the new fuel injection line. Loosely install the fuel injection line. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install".Note: Ensure that the ends of the fuel injection line are seated in the electronic unit injector and the fuel manifold. Tighten the nuts finger tight.
Use Tooling (B) to tighten torx screw (13) to a torque of 27 N m (239 lb in).Note: Tooling (B) must be used to ensure no damage to the rocker arms.
Tighten the clamps and the fuel injection lines. Use Tooling (E) to tighten the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install" for more information.
Illustration 4 g01772534
Typical example
Illustration 5 g01774093
Typical example
The electronic unit injector is not shown for clarity.


Back to top