0380803 EVINRUDE SHAFT, Propeller


0380803 SHAFT, Propeller EVINRUDE 65832B, 85852A SHAFT
0380803 SHAFT, Propeller EVINRUDE
Rating:
58

Buy SHAFT, Propeller 0380803 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 49
 

Compatible models:

65832B   85852A   EVINRUDE

BRP EVINRUDE entire parts catalog list:

65832B, 65833B, 65852B, 65853B 1968
85852A, 85853A 1968

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 463-3380 Lift As 1
B 9X-8897 Bolt 2 Note: This procedure is intended for the removal of the guard assemblies in a shop environment. Conditions must be solid, flat, smooth, and unobstructed. Fully read this procedure and fully understand this procedure before proceeding with the work.Note: Use caution around potential pinch points. Be alert for possible movement of the guard assemblies.Note: Inspect all tooling for proper condition and proper operation.Note: Do not place any part of your body under the guard assemblies unless the mounting hardware is installed. Make sure that the tooling is in the proper location and giving proper support to the guard assemblies before the mounting hardware is removed.Note: Bottom guards may contain a significant amount of rock, dirt, liquids, and debris, which could result in significant extra weight.
Illustration 1 g06219509
Front Guard Assembly
Position Tooling (A) under front guard assembly (5). The weight of front guard assembly (5) is approximately 368 kg (810 lb).
Remove hinge bolts (4) and the nuts and the washers. Remove inspection latch bolt (6), the washer, and the lock nut.
Remove six bolts (2) and loosen but do not remove mounting nuts (3) and bolts (1). If necessary, use Tooling (B) to pry front guard assembly (5) from the machine frame.
Ensure that no people are under front guard assembly (5). Remove bolts (1) and the washers and nuts (3) and the washers. Use Tooling (A) to remove front guard assembly (5).
Illustration 2 g06285942
Front Center Guard Assembly
Position Tooling (A) under front center guard assembly (9). The weight of front center guard assembly (9) is approximately 295 kg (650 lb).
Remove hinge bolts (7) and the nuts and the washers. Remove the inspection latch bolt (Not Shown), the washer, and the lock nut. Loosen but do not remove mounting nuts (8). If necessary, use Tooling (B) to pry front center guard assembly (9) from the machine frame.
Ensure that no people are under front center guard assembly (9). Remove mounting nuts (8) and the washers. Use Tooling (A) to remove front center guard assembly (9).
Illustration 3 g06285945
Rear Center Guard Assembly
Position Tooling (A) under rear center guard assembly (12). The weight of rear center guard assembly (12) is approximately 295 kg (650 lb).
Remove hinge bolts (10) and the nuts and the washers. Remove the inspection latch bolt (Not Shown), the washer, and the lock nut. Loosen but do not remove mounting nut (11). If necessary, use Tooling (B) to pry rear center guard assembly (12) from the machine frame.
Ensure that no people are under rear center guard assembly (12). Remove mounting nuts (11) and the washers. Use Tooling (A) to remove rear center guard assembly (12).
Illustration 4 g06285946
Rear Guard Assembly
Position Tooling (A) under rear guard assembly (15). The weight of rear guard assembly (15) is approximately 295 kg (650 lb).
Remove two hinge bolts (13) and the nuts and the washers. Remove the inspection latch bolt (Not Shown), the washer, and the lock nut. Loosen but do not remove mounting nuts (14). If necessary, use Tooling (B) to pry rear guard assembly (15) from the machine frame.
Ensure that no people are under rear guard assembly (15). Remove mounting nuts (14) and the washers. Use Tooling (A) to remove rear guard assembly (14).


Parts shaft EVINRUDE:

0382042
 
0382042 SHAFT ASSY., Throttle
65832B, 85852A, 85892A
0379240
0311062
0379882
 
0379882 SHAFT, Drive, standard
65832B, 85852A, 85892A
0379883
Back to top