0387214 EVINRUDE SHIFT LEVER & STUD


0387214 SHIFT LEVER & STUD EVINRUDE 200640S SHIFT
0387214 SHIFT LEVER & STUD EVINRUDE
Rating:
78

Buy SHIFT LEVER & STUD 0387214 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 44
 

Compatible models:

200640S   EVINRUDE

BRP EVINRUDE entire parts catalog list:

200640S, 200649S 1976

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     6V-6192     Pliers     1    
B     7M-3978     Ring Expander     1    
C     5P-8639     Hydraulic Press (Connecting Rod Bearing)     1    
8F-0024 Hose Assembly     1    
1P-2375 Connecting Coupler     1    
1P-2376 Connecting Coupler     1    
5P-8651 Spacer     1    
5P-8649 Adapter     1    
5P-8650 Bushing Adapter     1    
- Hydraulic Pump     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00786693
Illustration 2 g00507526
Install piston pin bearing (6) in connecting rod (4) , as follows:Note: The old bearing is pushed out by Tool (C) as the new bearing is installed.
Illustration 3 g00570892
The connecting rod must be heated for the installation of the piston pin bearing. Do not use a torch.
Heat length (Y) of connecting rod (4) to a temperature of 175 to 260 °C (347 to 468 °F). (Y) Maximum length for heating the connecting rod ... 85.0 mm (3.35 inch)
Use Tool (C) to remove the old bearing and install the new bearing at the same time. The adapter of Tool (C) should make full contact with the surfaces of the connecting rod.Note: Orient the bearing joint within 5 degrees of either location (X) .
Allow the connecting rod and the bearing to cool to room temperature.
Use a pin boring machine to machine the bore of the piston pin bearing to the correct diameter.Diameter of piston pin bore ... 50.830 .008 mm (2.0012 0.0003 inch)
Check the clearance between the ends of the piston rings (5) . Refer to Specifications, "Pistons And Rings" for additional information.Note: The oil ring is installed over the spring with the oil ring end gap 180 degrees from the oil ring spring joint.
Install the oil ring spring in the oil ring groove of the piston.
Illustration 4 g00507525
Install the oil ring on the piston with Tool (B) .
Use Tool (B) to install the intermediate piston ring with the side that has the identification "UP-2" toward the top of the piston.
Use Tool (B) to install the top piston ring with the side that has the identification "UP-1" toward the top of the piston.
Position the piston rings so the end gaps are 120 degrees from each other.
Put piston crown (7) in position on piston skirt (8) .
Put the piston in position on connecting rod (4) . Apply clean engine oil on piston pin (2) and install the piston pin. Install retainer rings (1) with Tool (A) . Ensure that the retainer rings are fully seated in the grooves of the piston.Note: Ensure that the bearings are installed so that the bearing tabs fit into the notch in the connecting rod and the connecting rod cap.
Install connecting rod bearings (3) in the connecting rod and the connecting rod cap.End By: Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".


Parts shift EVINRUDE:

0318138
 
0318138 SHIFT ROD
115393M, 115493B, 115593, 115693D, 115790S, 115793S, 135383M, 135443B, 135543E, 135643D, 150840S, 175740S, 200640S, 85393M, 85493B, 85593E, 85693D
0318185
 
0318185 SHIFT AND THROTTLE PLATE
115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 135383M, 135443B, 135543E, 135643D, 150840S, 175740S, 200640S, 50302R, 50442M, 50542B, 55642E, 55772D, 55874S, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 75542B, 75642D, 85393M, 85493
0386542
 
0386542 SHIFT LEVER ASSY
115493B, 115593, 115693D, 115790S, 115793S, 115890C, 135443B, 135543E, 135643D, 150840S, 175740S, 200640S, 50442M, 50542B, 55642E, 55772D, 55874S, 70442M, 70572B, 70673D, 70773S, 70873C, 75542B, 75642D, 85493B, 85593E, 85693D
0387171
 
0387171 SHIFT ASSY.,Gearcase
150840S, 175740S, 200640S
0320735
 
0320735 SHIFT ROD
115790S, 150840S, 175740S, 200640S
Back to top