5030505 EVINRUDE SHIM, (0.95mm)


5030505 SHIM, (0.95mm) EVINRUDE E70, E70FLTLECS, E70PL4EEC SHIM
5030505 SHIM, (0.95mm) EVINRUDE
Rating:
23

Buy SHIM, (0.95mm) 5030505 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E70, E70PL4SSR 2000
E70FLTLECS 1998
E70PL4EEC 1999

Information:


Illustration 1 g00819698 (1) Dowel pins The dowel pins in the cylinder block hold the cylinder head gasket in the correct position when the cylinder head is installed. (2) Cylinder head gasket
Table 1
Selection of Head Gasket for the C0.5, C0.7, C1.1/3011C and C1.6 Engines
Piston Height above Top Face of Cylinder Block Gasket Thickness
0.55 to 0.64 mm (0.0217 to 0.0252 inch) 1.2 mm (0.047 inch)
0.65 to 0.75 mm (0.0256 to 0.0295 inch) 1.3 mm (0.051 inch)
Table 2
Selection of Head Gasket for the C1.5/3013C Engines
Piston Height above Top Face of Cylinder Block Gasket Thickness
0.60 to 0.69 mm (0.0236 to 0.0272 inch) 1.3 mm (0.051 inch)
0.70 to 0.79 mm (0.0276 to 0.0311 inch) 1.4 mm (0.055 inch)
Table 3
Selection of Head Gasket for the C2.2/3024C Engine
Piston Height below Top Face of Cylinder Block Gasket Thickness
−0.45 to −0.30 mm (−0.0177 to −0.0118 inch) 0.4 mm (0.016 inch)
−0.29 to −0.20 mm (−0.0114 to −0.0079 inch) 0.5 mm (0.020 inch)
Table 4
Selection of Head Gasket for the C2.2/3024CT Engine
Piston Height below Top Face of Cylinder Block Gasket Thickness
−0.29 to −0.20 mm (−0.0177 to −0.0118 inch) 0.5 mm (0.020 inch) (3) The stamped marking on the cylinder head gasket must face upward. This ensures that the cylinder head gasket is installed correctly. Tightening Procedure for the Cylinder Head
C0.5 Engine
Illustration 2 g01112400Use the following procedure in order to tighten the bolts for the cylinder head.
Put clean engine oil on the threads of the bolts. The bolts are tightened in the numerical sequence that is shown in Illustration 2. Torque for bolts C0.5 ... 36.5 N m (26.9 lb ft)
Repeat the procedure in Step1 to ensure that all of the bolts are tightened to the correct torque. C0.7, C1.1/3011C and C1.5/3013C Engines
Illustration 3 g00900073Use the following procedure in order to tighten the bolts for the cylinder head.
Put clean engine oil on the threads of the bolts. The bolts are tightened in the numerical sequence that is shown in Illustration 3. Torque for bolts C0.7 ... 36.5 N m (26.9 lb ft)C1.1/3011C ... 51 N m (37.6 lb ft)C1.5/3013C ... 101 N m (74.5 lb ft)
Repeat the procedure in Step 1 to ensure that all of the bolts are tightened to the correct torque. C1.6 and C2.2/3024C and C2.2/3024CT Engines
Illustration 4 g00900074Use the following procedure in order to tighten the bolts for the cylinder head.
Put clean engine oil on the threads of the bolts. The bolts are tightened in the numerical sequence that is shown in Illustration 4. Torque for bolts C1.6 ... 51 N m (37.6 lb ft)C2.2/3024C and C2.2/3024CT ... 101 N m (74.5 lb ft)
Repeat the procedure in Step 1 to ensure that all of the bolts are tightened to the correct torque. Measuring the Distortion of the Cylinder Head
Illustration 5 g00900977
Typical example
Distortion of the cylinder head ... 0.00 to 0.05 mm (0.000 to 0.002 inch)Maximum service limit ... 0.12 mm (0.005 inch)Maximum limit for regrinding ... 0.15 mm (0.006 inch)Note: Use a straight edge and a feeler gauge to check the six positions for distortion.Refer to Testing and Adjusting, "Cylinder Head - Inspect" for the procedures for measuring the cylinder head.Note: If the cylinder head has been machined, check the valve depth below the cylinder head face. Refer to Specifications, "Cylinder Head Valves" for valve depth.


Parts shim EVINRUDE:

5030975
 
5030975 SHIM KIT, Driveshaft
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030490
 
5030490 SHIM, (0.70mm)
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030486
 
5030486 SHIM, (1.00mm)
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030485
 
5030485 SHIM, (0.80mm)
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5031097
SHIM, (0.65mm)
5031097 SHIM, (0.65mm)
E70, E70FLTLECS, E70PL4EEC
5030499
 
5030499 SHIM, (0.60mm)
E70, E70FLTLECS, E70PL4EEC
5030484
 
5030484 SHIM, (1.4mm)
E70, E70FLTLECS, E70PL4EEC
5030477
SHIM, Steering arm (0.3)
5030477 SHIM, Steering arm (0.3)
E40PL4EES, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SSC, E50PL4SSC, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
Back to top