5031850 EVINRUDE SHIM, 1.4mm


5031850 SHIM, 1.4mm EVINRUDE E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS SHIM
5031850 SHIM, 1.4mm EVINRUDE
Rating:
68

Buy SHIM, 1.4mm 5031850 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 23
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E25EL4SIC, E25PL4SIC, E25R4SIC, E25RL4SIC, E25TE4SIC, E25TEL4SIC 2001
E25EL4SSS, E25PL4SSS, E25R4SSS, E25RL4SSS, E25TE4SSS, E25TEL4SSS 2000
E30EL4SIC, E30PL4SIC, E30R4SIC, E30RL4SIC, E30TE4SIC, E30TEL4SIC 2001
E30EL4SSS, E30PL4SSS, E30R4SSS, E30RL4SSS, E30TE4SSS, E30TEL4SSS 2000

Information:


Illustration 1 g01161540
Typical example
Test Step 1. Check for Connector Damage.
Turn the battery disconnect switch to the OFF position.
Turn the breaker to the OFF position.
Thoroughly inspect the ECM connectors J1/P1 and J2/P2. Inspect all of the other connectors. Refer to the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the ECM connectors (allen head screw) for the proper torque. Refer to Troubleshooting, "Inspecting Electrical Connectors" for details.
Check the harness and the wiring for abrasion and for pinch points. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The connectors and wiring are OK. Proceed to Test Step 2.
Not OK - The connectors and/or wiring are not OK.Repair: Repair the connectors or wiring and/or replace the connectors or wiring.STOPTest Step 2. Verify the Proper Installation of the Terminating Resistors.
Verify that the terminating resistors are installed on the ends of the data link.
Disconnect J1/P1 ECM connector and measure the resistance between P1-50 (CAN data link +) and P1-34 (CAN data link -). Expected Result:The resistance is approximately 60 3 Ohms.Results:
OK - The resistance is within the range. Proceed to Test Step 3.
Not OK - The resistance is approximately 120 6 Ohms. A terminating resistor is missing or damaged.Repair: If a termination resistor is missing, install the missing resistor. If both resistors are present, measure the resistance between pin A and pin B of the termination resistor. The resistance should measure 120 3 Ohms. Replace the termination resistor if the resistance is not 120 3 Ohms.Refer to the schematic in order to determine the missing resistor.Verify that the repair eliminates the problem.STOPTest Step 3. Check for a Short Circuit in the Harness.
Disconnect the J1/P1 ECM connector, the generator connector , and the thermocouple connector.
Remove the terminating resistors from the harness for the CAN data link. Note: Wiggle the harness during the following measurements in order to reveal an intermittent condition.
Measure the resistance between P1-50 (CAN data link +) and the remaining terminals on the P1 connector.
Measure the resistance between P1-50 (CAN data link +) and the engine ground.
Measure the resistance between Pin-35 (CAN data link +) and the remaining terminals on the generator connector.
Measure the resistance between Pin-35 (CAN data link +) and the engine ground. Expected Result:The resistance is greater than 20000 Ohms.Results:
OK - The resistance is greater than 20000 Ohms. Proceed to Test Step 4.
Not OK - The resistance is less than 20000 Ohms.Repair: There is a short in the harness wiring. Repair the connectors or wiring and/or replace the connectors or wiring.Verify that the repair eliminates the problem.STOPTest Step 4. Check for an Open Circuit in the Harness.
All connections should remain disconnected.
Fabricate a jumper wire. Short pin G and pin F on the service tool connector.
Measure the resistance between Pin-35 (CAN data link +) and Pin-36 (CAN data link -) at the generator connector.
Short pin 2 and pin 3 on the thermocouple connector.
Measure the resistance between Pin-35 (CAN data link +) and Pin-36 (CAN data link -) at the generator connector.
Short pin A and pin B on any remaining connectors in the generator connector circuit.
Measure the resistance between Pin-35 (CAN data link +) and Pin-36 (CAN data link -) at the generator connector.
Short pin A and pin B on any connectors in the ECM circuit.
Measure the resistance between P-50 (CAN data link +) and P-34 (CAN data link -) at the ECM connector. Expected Result:The resistance is less than 5 Ohms.Results:
OK - The resistance is less than 5 Ohms.Repair: The harness for the CAN data link is OK. STOP
Not OK - The resistance is greater than 5 Ohms.Repair: There is an open in the harness wiring. Repair the connectors or wiring and/or replace the connectors or wiring. Make the necessary repairs.Verify that the repair eliminates the problem.STOP


Parts shim EVINRUDE:

5031836
SHIM, 1.8mm
5031836 SHIM, 1.8mm
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5032299
 
5032299 SHIM, 2.2mm
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5032298
 
5032298 SHIM, 2.0mm
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031838
 
5031838 SHIM, 2.1mm
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031835
 
5031835 SHIM, 1.7mm
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031868
 
5031868 SHIM, 1.5mm
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031871
 
5031871 SHIM, 1.0mm
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031869
 
5031869 SHIM, 0.8mm
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
Back to top