0305545 EVINRUDE SLEEVE,Bendix drive

Parameter Descriptions
"Product ID"
The "Product ID" parameter allows the customer to enter a description into the ECM in order to identify the machine. A maximum of 8 characters can be entered in the field."Equipment ID"
The "Equipment ID" parameter allows the customer to enter a description into the ECM in order to identify the machine. A maximum of 17 characters can be entered in the field."Engine Serial Number"
Program the "Engine Serial Number" to match the engine serial number that is stamped on the engine information plate. The engine serial number is not preprogrammed on a replacement ECM."ECM Serial Number"
This parameter identifies the serial number for the ECM."Software Group Part Number"
This parameter identifies the part number of the flash file that is currently installed in the ECM."FLS" (Full Load Setting)
"FLS" is a number that represents the adjustment to the fuel system that was made at the factory in order to fine tune the fuel system. The correct value for this parameter is stamped on the engine information plate. Only change this value if the engine is rerated or if a new ECM is installed. Factory passwords are required."FTS" (Full Torque Setting)
"FTS" is similar to "FLS". Only change this value if the engine is rerated or if a new ECM is installed. Factory passwords are required."Total Tattletale"
The total tattletale counts the number of changes to system parameters."Ether Solenoid Configuration"
The "Ether Solenoid Configuration" parameter allows the operation of this feature to be "Not Installed" or "Continuous Flow"."Security System Immobilizer"
This parameter allows the Machine Security System (MSS) to be disabled or removed. If the MSS is removed from the machine, this parameter must be programmed to "Not Installed". Otherwise, the engine will not start. Factory passwords are required."System Battery Voltage Low Elevated Idle"
The "System Battery Voltage Low Elevated Idle" parameter allows the operation of this feature to be enabled or disabled.Parameter Table
Table 1
Customer Specified Parameters    
Parameter    Available Range or Options    Default    Required Password    
"Product ID"     8 characters     Blank     None    
"Equipment ID"     17 characters     Blank     None    
"Engine Serial Number"     8 characters     Blank     None    
"ECM Serial Number"     Hardware Dependent     Blank     Read Only    
"Software Group Part Number"     Software Dependent     Blank     Read Only    
"FLS"     -128 to +127     0     Factory    
"FTS"     -128 to +127     0     Factory    
"Total Tattletale"     0 to 65535     0     Read Only    
"Ether Solenoid Configuration"     "Not Installed" or "Continuous Flow"     "Continuous Flow"     None    
"Security System Immobilizer"     "Installed" or "Not Installed"     "Not Installed"     Factory    
"System Battery Voltage Low Elevated Idle"     "Enabled" or "Disabled"     "Enabled"     None    Parameter Worksheet
Record the following information before you change any programmable parameter.
Table 2
Information from ECM    
"Product ID"    
   
"Equipment ID"    
   
"Engine Serial Number"    
   
"ECM Serial Number"    
   
"Software Group Part Number"    
   
"FLS"    
   
"FTS"    
   
"Total Tattletale"    
   
"Ether Solenoid Configuration"    
   
"Security System Immobilizer"    
   
"System Battery Voltage Low Elevated Idle"    
   
Information From Engine Information Plate    
Engine Serial Number    
   
Full Load Setting
(for new ECM)    
   
Full Torque Setting
(for new ECM)    
   
Injector Code (1)    
   
Injector Code (2)    
   
Injector Code (3)    
   
Injector Code (4)    
   
Injector Code (5)    
   
Injector Code (6)    
   Note: Compare the FLS and the FTS from the ECM with the values that are listed on the engine information plate. O