0386664 EVINRUDE SOLENOID ASSY., Choke


0386664 SOLENOID ASSY., Choke EVINRUDE 115493B, 115593, 115693D, 135443B, 135543E, 135643D, 85493B, 85593E, 85693D SOLENOID
0386664 SOLENOID ASSY., Choke EVINRUDE
Rating:
83

Buy SOLENOID ASSY., Choke 0386664 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$158.98
 

30-01-2023
1.0[0.45] Pounds
-: -
OMC Choke Solenoid P/N 386664 0386664 NOS
Genuine OEM OMC Part || OEM Solenoid || Part Number: 386664 || May not include original package.
Number on catalog scheme: 17
 

BRP EVINRUDE entire parts catalog list:

115493B 1974
115593 1975
115693D, 115693G, 115699D, 115699G 1976
135443B, 135483B, 135489B 1974
135543E, 135583E, 135589E 1975
135643D, 135643G, 135683D, 135683G 1976
85493B 1974
85593E 1975
85693D, 85693G, 85699G 1976

Information:


Illustration 1 g03566901
The GSC+ uses the programmable spare relay (PSR) in order to activate the customer equipment. See Systems Operation, "Spare Input/Output Programming OP6".Note: Whenever the GSC+ activates or the GSC+ attempts to activate the PSR, K8 is shown on the lower display. When the PSR is not activated, K8 is not shown.The possible cause of a CID 0448 FMI 12 is an open coil or a shorted coil of the PSR.The system responses to these diagnostic codes are listed below.
If a CID 0448 FMI 12 occurs and the PSR is active, any customer equipment on RM-25 (normally open) will be deactivated. Any customer equipment on RM-26 (normally closed) will remain activated.
If a CID 0448 FMI 12 occurs while the PSR is inactive, any customer equipment on RM-25 (normally open output) will remain deactivated. Any customer equipment on RM-26 (normally closed) will remain activated.The GSC+ treats a CID 0448 FMI 12 as an alarm fault. Active alarm faults are shown on the display when the "Alarm Codes" key is pressed and the ECS is in any position except the OFF/RESET position. Clear the diagnostic code from the fault log after troubleshooting is complete.This troubleshooting procedure is for an active CID 0448 or the troubleshooting procedure is for an inactive CID 448 FMI 12.
Check the status of the diagnostic code.
Turn the ECS to the OFF/RESET position and then turn the ECS to the STOP position.
Press the "Alarm Codes" key.
Observe the upper display. Check that the CID 0448 FMI 12 is active.
If the diagnostic code is not active, enter the Service Mode. View the fault log for an OP1. Check that the diagnostic code is inactive.Expected Result: A CID 0448 FMI 12 is displayed as an active diagnostic code or CID 0448 FMI 12 is displayed as an inactive diagnostic code.Results:
OK: The CID 0448 FMI 12 is active or the CID 0448 FMI 12 is inactive. Proceed to Step 2.
NOT OK: The CID 0448 FMI 12 has not occurred. The diagnostic code is not active and the diagnostic code is not inactive. 2 STOP.
Check the internal cable of the relay module.Note: Only open the relay module in a dry environment. If the inspection and repair will take more than approximately 20 minutes, replace the desiccant bag in the GSC+ housing. See Testing and Adjusting, "Relay Module - Replace".
Turn the ECS to the OFF/RESET position.
Disconnect the battery negative cable.
Temporarily, remove the relay module from the GSC+. See Testing and Adjusting, "Relay Module - Replace"
Check the cable that attaches the relay module to the GSC+.Expected Result: Firmly seated cable in the connector. The clamp should be in place. The cable should not be damaged.Results:
OK: The cable is firmly seated in the connector. The clamp is in place. The cable is not damaged. Reassemble the relay module to the GSC+. Proceed to step 3.
NOT OK: One or more of the components are damaged or the components are missing.Repair: Replace the clamp if the clamp is missing. If the cable is damaged, replace the GSC+. STOP.
Functional Check Of The PSR.
Turn the ECS to the OFF/RESET position.
Reconnect the battery negative cable.
Disconnect all wires from RM-25 of the relay module.
Remove fuse "F9" from the relay module.
At the relay module, measure the resistance from RM-25 to RM-11. Make a note of the resistance measurement.
Turn the ECS to the START position. Measure the resistance from RM-25 to RM-11. Make a note of the resistance measurement.Expected Result: The initial resistance measurement after removing the wires and the fuse from the relay module should be greater than 5000 ohms. The resistance measurement should be less than 5 ohms when the ECS is placed in the START position.Results:
OK: The resistance measurements are correct. The problem does not exist at this time. The initial problem was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal operation and watch for a recurrence. STOP.
NOT OK: Either one of the resistance measurements are NOT correct. The relay module has failed.Repair: Replace the relay module. See Testing and Adjusting, "Relay Module - Replace". STOP.


Parts solenoid EVINRUDE:

0383622
SOLENOID ASSY., Starter
0383622 SOLENOID ASSY., Starter
100193A, 100293R, 100990S, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802
0979774
0172762
0387288
 
0387288 SOLENOID ASSY., Choke
115693D, 115790S, 115793S, 135643D, 150840S, 175740S, 200640S, 55642E, 55772D, 55874S, 70673D, 70773S, 70873C, 75642D, 85693D
0581528
SOLENOID ASSY.
0581528 SOLENOID ASSY.
100990S, 115693D, 115790S, 115793S, 115890C, 135643D, 150840S, 150940C, 175740S, 200640S, 85693D, E100MLCSC, E115MLCIH, E115MLCSA, E140MLCIH, E140MLCSA, E150TRLCIA, E150TRLCSF, E175TRLCIM, E175TRLCSA, E200TRLCIB, E200TRLCSF, E235TRLCIB, E235TRLCSM, E
0387562
 
0387562 SOLENOID & CABLE ASSY.
115693D, 135643D, 85693D
Back to top