0316373 SPINDLE, Pulley EVINRUDE
2102A, 2202M, 2302B, 2402E, 2502D, 2602S, 2702C, 2802R, 2902A, 4904D, E2RCIB, E2RCNE, E2RCOC, E2RCRS, E2RCSM, E2RCTD, E4BRCICI, E4BRHCCS, E4BRHCDE, E4BRHCNR, E4BRHCOB, E4BRHCRM, E4BRHCTA, E4BRHCUD, E4RLCSS, E4WCIC, E4WCNR, EJR-CCM, EJR-CDR, EJR-CUA
SPINDLE
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- REWIND STARTE » 0316373
- REWIND STARTER
2302B 1973
2402E 1974
2502D 1975
2602S 1976
2702C 1977
2802R 1978
2902A 1979
4904D, 4932D, 4933D 1979
E2RCIB 1981
E2RCNE 1982
E2RCOC 1985
E2RCRS 1984
E2RCSM 1980
E2RCTD 1983
E4BRCICI, E4BRLCIC 1981
E4BRHCCS, E4BRHLCCS 1988
E4BRHCDE, E4BRHLCDE 1986
E4BRHCNR, E4BRHLCNR 1982
E4BRHCOB, E4BRHLCOB 1985
E4BRHCRM, E4BRHLCRM 1984
E4BRHCTA, E4BRHLCTA 1983
E4BRHCUD, E4BRHLCUD 1987
E4RLCSS, E4WCSS 1980
E4WCIC 1981
E4WCNR 1982
EJR-CCM 1988
EJR-CDR 1986
EJR-CUA 1987
Information:
1. Remove bolts (1) and lift shaft (2) and the rocker arms off the valve cover base and the push rods. 2. Remove push rods (3) from the valve lifters and valve cover base. 3. Remove bridge assemblies (4) from the dowels.Install Rocker Shaft Assemblies & Push Rods
1. Loosen the adjustment nuts and screws (1) on valve bridges (2).2. Put clean engine oil on the bridge dowels, the inside diameter of valve bridges (2) and on the top pad of the valve bridge. Install valve bridges (2) on the bridge dowels as shown.3. While bridges (2) are pushed straight down with a force of 25 20 N (5.6 4.5 lb) on the top contact surface, turn adjustment screw (1) until it makes contact with the valve stem. Turn screw (1) another 20 to 30 degrees. This will straighten the dowel in the guide and make compensation for clearance (slack) in the threads.4. Hold adjustment screw (1) in position and tighten the nut around screw (1) to a torque of 30 4 N m (22 3 lb ft). 5. Put push rods (3) in position in the valve lifters and valve cover base.
Make sure the crankshaft and camshafts are in time with each other and that adjustment screws (5) are turned all the way out before the rocker shaft bolts are tightened or damage to the valves or pistons can be the result. See the topic "Install Camshafts" for the procedure to time the engine.
6. Put the rocker arms and shaft (4) in position on the valve cover base. Make sure the rocker shafts and push rods are in alignment and install the bolts to hold shaft (4).7. Make an adjustment of the valves to have a clearance of 0.40 mm (.016 in) for intake and 0.76 mm (.030 in) for exhaust. See the topic "Valve Clearance Setting" in the Testing & Adjusting Manual for the complete procedure.End By:a. install valve coversDisassemble Rocker Shaft Assemblies
Start By:a. remove rocker shaft assemblies 1. Slide shaft assembly (1) out of rocker arms (2). If necessary, remove the dowel from shaft assembly (1). 2. Remove adjustment screw (4) and the nut from rocker arm (2).3. Use a hammer and punch to push socket (3) out of rocker arm (2). 4. Remove the ring that holds button (5) in socket (3) and remove the button from the socket. 5. Use Tool (A) to remove bearing (6) from rocker arm (2).6. Do Steps 2 through 5 for the other two rocker arms.Assemble Rocker Shaft Assemblies
1. Make an alignment of the oil hole (slot) in the bearing with the oil passage in rocker arm (1). Use Tool (A) to install the bearing in rocker arm (1) with the joint in the bearing toward the top of the rocker arm. The bore in the bearing must be 37.140 0.015 mm (1.4622 .0006 in) after assembly. 2. Make an alignment of the scribe mark on socket (2) with the mark on rocker arm (1) and install the socket in the rocker arm.3. Put button (3) in socket (2) and install ring (4) to hold the unit together. 4. Install adjustment screw (5) and nut (6) on rocker arm (1).5. Do Steps 1 through 4 for the other two rocker arms. 6. If the dowel was removed from shaft assembly (7), install the new dowel in the shaft until it is 7.70 0.50 mm (.303 .020 in) above the surface of the shaft.7. Put clean engine oil on the rocker arm bearings and shaft assembly (7). Install rocker arms (1) on shaft assembly (7).End By:a. install rocker shaft assemblies
1. Loosen the adjustment nuts and screws (1) on valve bridges (2).2. Put clean engine oil on the bridge dowels, the inside diameter of valve bridges (2) and on the top pad of the valve bridge. Install valve bridges (2) on the bridge dowels as shown.3. While bridges (2) are pushed straight down with a force of 25 20 N (5.6 4.5 lb) on the top contact surface, turn adjustment screw (1) until it makes contact with the valve stem. Turn screw (1) another 20 to 30 degrees. This will straighten the dowel in the guide and make compensation for clearance (slack) in the threads.4. Hold adjustment screw (1) in position and tighten the nut around screw (1) to a torque of 30 4 N m (22 3 lb ft). 5. Put push rods (3) in position in the valve lifters and valve cover base.
Make sure the crankshaft and camshafts are in time with each other and that adjustment screws (5) are turned all the way out before the rocker shaft bolts are tightened or damage to the valves or pistons can be the result. See the topic "Install Camshafts" for the procedure to time the engine.
6. Put the rocker arms and shaft (4) in position on the valve cover base. Make sure the rocker shafts and push rods are in alignment and install the bolts to hold shaft (4).7. Make an adjustment of the valves to have a clearance of 0.40 mm (.016 in) for intake and 0.76 mm (.030 in) for exhaust. See the topic "Valve Clearance Setting" in the Testing & Adjusting Manual for the complete procedure.End By:a. install valve coversDisassemble Rocker Shaft Assemblies
Start By:a. remove rocker shaft assemblies 1. Slide shaft assembly (1) out of rocker arms (2). If necessary, remove the dowel from shaft assembly (1). 2. Remove adjustment screw (4) and the nut from rocker arm (2).3. Use a hammer and punch to push socket (3) out of rocker arm (2). 4. Remove the ring that holds button (5) in socket (3) and remove the button from the socket. 5. Use Tool (A) to remove bearing (6) from rocker arm (2).6. Do Steps 2 through 5 for the other two rocker arms.Assemble Rocker Shaft Assemblies
1. Make an alignment of the oil hole (slot) in the bearing with the oil passage in rocker arm (1). Use Tool (A) to install the bearing in rocker arm (1) with the joint in the bearing toward the top of the rocker arm. The bore in the bearing must be 37.140 0.015 mm (1.4622 .0006 in) after assembly. 2. Make an alignment of the scribe mark on socket (2) with the mark on rocker arm (1) and install the socket in the rocker arm.3. Put button (3) in socket (2) and install ring (4) to hold the unit together. 4. Install adjustment screw (5) and nut (6) on rocker arm (1).5. Do Steps 1 through 4 for the other two rocker arms. 6. If the dowel was removed from shaft assembly (7), install the new dowel in the shaft until it is 7.70 0.50 mm (.303 .020 in) above the surface of the shaft.7. Put clean engine oil on the rocker arm bearings and shaft assembly (7). Install rocker arms (1) on shaft assembly (7).End By:a. install rocker shaft assemblies