0330524 EVINRUDE SPINDLE, Starter


0330524 SPINDLE, Starter EVINRUDE B25JREUR, BE20SRECB, BE20SREDA, BE20SREUM, BE25BAECM, BE25BAEDR, BE30BAECS, BE30BAEDE, BE30BAEEC, BE30BAEUD, BE30BASIA, BE30BASSR, E20CRCCA, E20CRCDC, E20CRCEM, E20CRCOS, E20CRCUR, E20CREDA, E20CREIE, E20CREND, E20CREOR, E20CRERC, E20CRESB, E20CRETS, SPINDLE
0330524 SPINDLE, Starter EVINRUDE
Rating:
18

Buy SPINDLE, Starter 0330524 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

BRP EVINRUDE entire parts catalog list:

B25JREUR, BE25BAEUA, BE25BALEUA, E25REUM, E25RLEUM, HE25RAEUM, SE25RDEUR 1997
BE20SRECB, BE20SRLECB 1998
BE20SREDA, BE20SRLEDA 1996
BE20SREUM, BE20SRLEUM, E20CREUM, E20CRLEUM 1997
BE25BAECM, BE25BALECM, E25JRECA, E25RECB, E25RLECB, SE25RDECA 1998
BE25BAEDR, BE25BALEDR, BE25BREDC, BE25BRLEDC, HE25RAEDA, SE25RDEDC 1996
BE30BAECS, BE30BALECS 1998
BE30BAEDE, BE30BALEDE 1996
BE30BAEEC, BE30BAEEN 1999
BE30BAEUD, BE30BALEUD, E30REUD, E30RLEUD 1997
BE30BASIA 2001
BE30BASSR 2000
E20CRCCA, E20CRLCCA, E20ECCA, E20ELCCA 1988
E20CRCDC, E20CRLCDC, E20ECDC, E20ELCDC, E20TECDC 1986
E20CRCEM, E20CRLCEM, TE20CRCEM, TE20CRLCEM, TE20CRLESF 1989
E20CRCOS, E20CRLCOS, E20ECOS, E20ELCOS 1985
E20CRCUR, E20CRLCUR, E20ECUR, E20ELCUR 1987
E20CREDA, E20CRLEDA, HE20CREDA, HE20CRLEDA 1996
E20CREIE, E20CRLEIE, TE20CRLEIE 1991
E20CREND, E20CRLEND, TE20CREND, TE20CRLEND 1992
E20CREOR, E20CRLEOR 1995
E20CRERC, E20CRLERC 1994
E20CRESB, E20CRLESB, TE20CRESB, TE20CRLESB 1990
E20CRETS, E20CRLETS, TE20CRETS, TE20CRLETS 1993
E25ECCM, E25ELCCM, E25RCCA, E25RLCCA, E25TECCA, E25TELCCA 1988
E25ECDR, E25ELCDR, E25RCDC, E25RLCDC, E25TECDC, E25TELCDC 1986
E25ECOC, E25ELCOC, E25RCOS, E25RLCOS, E25TECOS, E25TELCOS 1985
E25ECUA, E25ELCUA, E25RCUR, E25RLCUR, E25TECUR, E25TELCUR 1987
E25JREDC 1996
E25JREOS 1995
E25RCEM, E25RLCEM 1989
E25REDA, E25RLEDA, HE25REDA, HE25RLEDA 1996
E25REIE, E25RLEIE, VE25REIE 1991
E25REND, E25RLEND 1992
E25REOR, E25RLEOR 1995
E25RERC, E25RLERC 1994
E25RESB, E25RLESB, VE25RESB 1990
E25RETS, E25RLETS 1993
E25RWCDC, E25RWLCDC 1986
E25RWCOS, E25RWLCOS 1985
E25RWCUR, E25RWLCUR 1987
E25RWEDC, E25RWLEDC, HE25FPO, HE25RSLO 1996
E25RWEIM, E25RWLEIM 1991
E25RWENB, E25RWLENB 1992
E25RWEOS, E25RWLEOS 1995
E25RWERD, E25RWLERD 1994
E25RWESA, E25RWLESA 1990
E25RWETE, E25RWLETE 1993
E25RWEUR, E25RWLEUR, HE25FPV, HE25RSLV, SE25RPLV, SE25RPV 1997
E25RWK, E25RWLK 1989
E25WREEN, E25WREES, E25WRLEEN, E25WRLEES 1999
E25WRLSIR, E25WRSIR 2001
E25WRLSSC, E25WRSSC 2000
E30ECCE, E30ELCCE, E30RCCE, E30RLCCE, E30TECCE, E30TELCCE 1988
E30ECDM, E30ELCDM, E30RCDM, E30RLCDM, E30TECDM, E30TELCDM 1986
E30ECOA, E30ELCOA, E30RCOA, E30RLCOA, E30TECOA, E30TELCOA 1985
E30ECUB, E30ELCUB, E30RCUB, E30RLCUB, E30TECUB, E30TELCUB 1987
E30RCED, E30RLCED 1989
E30REDE, E30RLEDE, HE30REDE, HE30RLEDE 1996
E30REIC, E30RLEIC 1991
E30RENR, E30RLENR 1992
E30REOB, E30RLEOB 1995
E30RERM, E30RLERM 1994
E30RESS, E30RLESS 1990
E30RETA, E30RLETA 1993
E35RCCE, E35RLCCE 1988
E35RCDM, E35RLCDM 1986
E35RCED, E35RLCED 1989
E35RCUB, E35RLCUB 1987
E35REIC, E35RLEIC 1991
E35RENR, E35RLENR 1992
E35RERM, E35RLERM 1994
E35RESS, E35RLESS 1990
E35RETA, E35RLETA 1993
SE25RDEEM, SE25RDEEN 1999
SE25RDSIE 2001
SE25RDSSB 2000
SE25RPLP, SE25RPP 1998
SE35REDE, SE35RLEDE 1996
U25RWA, U25RWLA 1988

Information:

Recommended Actions
Diagnostic Codes, Event Codes, and Electrical Power Supply to the ECM
Certain diagnostic codes and/or event codes may prevent the engine from starting. Connect Caterpillar Electronic Technician (ET) and check for active codes and/or for logged codes. Troubleshoot any codes that are present before continuing with this procedure.Note: If Cat ET will not communicate with the ECM, the problem is most likely with the electrical power supply to the ECM. Refer to Troubleshooting, "Electrical Power Supply - Test".Fuel Supply
Visually check the fuel level. Do not rely on the fuel gauge only. If necessary, add fuel. If the engine has been run out of fuel, it will be necessary to prime the fuel system. Refer to Operation and Maintenance Manual for the correct procedure.
Check the fuel lines for the following problems: restrictions, collapsed lines and pinched lines. If problems are found with the fuel lines, repair the lines and/or replace the lines.
Check the fuel tank for foreign objects which may block the fuel supply.
Prime the fuel supply system if any of the following procedures have been performed:
Replacement of the fuel filters
Service on the low pressure fuel supply circuitNote: A sight glass in the supply line is helpful in diagnosing air in the fuel. Refer to the Systems Operation/Testing and Adjusting manual for more information.
Cold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.Electrical Power Supply to the Electronic Control Module (ECM)
Check power to the ECM. Refer to Troubleshooting, "Electrical Power Supply - Test".Note: If the ECM is not receiving battery voltage, the ECM will not communicate.Electrical Connectors
Inspect each connector for moisture and corrosion. Also, inspect the harness from the ECM to the sensors. Refer to Troubleshooting, "Electrical Connectors - Inspect".Air Inlet and Exhaust System
Check the air filter restriction indicator for a plugged filter. If necessary, service the engine. Refer to the Operation and Maintenance Manual.
Check the air inlet and exhaust system for restrictions and/or leaks. Refer to Systems Operation/Testing and Adjusting.
Check flame arrester for blockage on ATEX engines.Engine Shutdown Switches (if applicable)
The engine shutdown switches should be in the OFF position. Use Cat ET to verify the status of the shutdown switches. When a shutdown occurs, the keyswitch must be turned to the OFF position for at least 15 seconds before restarting the engine.The air shutoff switch must be in the OPEN position on an ATEX engine.Engine Speed/Timing
Crank the engine and observe the engine speed on the Cat ET status screen. If Cat ET indicates zero rpm, refer to Troubleshooting, "Engine Speed/Timing Sensor".Note: Upon initial cranking, the status for engine speed may indicate that the engine speed signal is abnormal. This message will be replaced with an engine speed once the ECM is able to calculate a speed from the signal.
Ensure that the timing reference gear is installed correctly. The engine will not start if the gear was installed backward. Check for proper orientation between the crankshaft and camshaft drive gears. Correct the orientation and/or replace the drive gear, if necessary. Refer to the Disassembly and Assembly manual.Unit Injectors
Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM. Refer to Troubleshooting, "Injector Solenoids" for additional information.Combustion
Check for mechanical problems in the combustion system.


Back to top