5007182 EVINRUDE STEERING ARM & SHAFT Assy


5007182 STEERING ARM & SHAFT Assy EVINRUDE E15DHPLAAA, E15DHPLAAB, E15DHPLIIC, E15DHPLINR, E15DHPLISS, E15DHTLAAA, E15DHTLAAB, E15DHTLIIC, E15DHTLINR, E15DHTLISS, E25DELAAA, E25DELIIH, E25DELINA, E25DELISC, E25DELSES, E25DPLAAA, E25DPLAAB, E25DPLIIG, E25DPLIIH, E25DPLINA, E25DPLISC, E25DPLSES STEERING
5007182 STEERING ARM & SHAFT Assy EVINRUDE
Rating:
33

Buy STEERING ARM & SHAFT Assy 5007182 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 51
 

BRP EVINRUDE entire parts catalog list:

E15DHPLAAA, E15HPSLAAA, E15HPSXAAA 2012
E15DHPLAAB, E15HPSLAAB, E15HPSXAAB 2012
E15DHPLIIC, E15DHPLIIH, E15HPSLIIH, E15HPSLIIS 2011
E15DHPLINR, E15HPSLINC, E15HPSXINC 2012
E15DHPLISS 2010
E15DHTLAAA, E15HTSLAAA, E15HTSXAAA 2012
E15DHTLAAB, E15HTSLAAB, E15HTSXAAB 2012
E15DHTLIIC, E15DHTLIIH, E15HTSLIIH, E15HTSLIIS 2011
E15DHTLINR, E15HTSLINC, E15HTSXINC 2012
E15DHTLISS 2010
E25DELAAA, E25DELAAB 2012
E25DELIIH, E25DELIIR 2011
E25DELINA 2012
E25DELISC 2010
E25DELSES 2009
E25DPLAAA, E25DPSLAAA 2012
E25DPLAAB, E25DPSLAAB 2012
E25DPLIIG 2011
E25DPLIIH, E25DPLIIR, E25DPSLIIH, E25DPSLIIS 2011
E25DPLINA, E25DPSLINC 2012
E25DPLISC 2010
E25DPLSES 2009
E25DRAAA, E25DRAAB, E25DRLAAA, E25DRLAAB, E25DRSAAA, E25DRSAAB, E25DRSLAAA, E25DRSLAAB 2012
E25DRIIH, E25DRIIR, E25DRLIIH, E25DRLIIR, E25DRSIIH, E25DRSIIS, E25DRSLIIH, E25DRSLIIS 2011
E25DRINA, E25DRLINA, E25DRSINC, E25DRSLINC 2012
E25DRISC, E25DRLISC 2010
E25DRLSES, E25DRSES 2009
E25DTEAAA, E25DTEAAB, E25DTELAAA, E25DTELAAB, E25TESLAAA, E25TESLAAB 2012
E25DTEIIG 2011
E25DTEIIH, E25DTEIIR, E25DTELIIH, E25DTELIIR, E25TESLIIH, E25TESLIIS 2011
E25DTEINA, E25DTELINA, E25TESLINC 2012
E25DTEISC, E25DTELISC 2010
E25DTELSES, E25DTESES 2009
E25DTLAAA, E25DTSLAAA 2012
E25DTLAAB, E25DTSLAAB 2012
E25DTLIIH, E25DTLIIR, E25DTSLIIH, E25DTSLIIS 2011
E25DTLINA, E25DTSLINC 2012
E25DTLISC 2010
E25DTLSES 2009
E30DELAAA, E30DELAAB 2012
E30DELIIH, E30DELIIR 2011
E30DELINA 2012
E30DELISC 2010
E30DELSES 2009
E30DPLAAA, E30DPSLAAA 2012
E30DPLAAB, E30DPSLAAB 2012
E30DPLIIH, E30DPLIIR, E30DPSLIIH, E30DPSLIIS 2011
E30DPLINA, E30DPSLINC 2012
E30DPLISC 2010
E30DPLSES 2009
E30DRAAA, E30DRAAB, E30DRLAAA, E30DRLAAB, E30DRSAAA, E30DRSAAB, E30DRSLAAA, E30DRSLAAB 2012
E30DRIIG, E30DRLIIG 2011
E30DRIIH, E30DRIIR, E30DRLIIH, E30DRLIIR, E30DRSIIH, E30DRSIIS, E30DRSLIIH, E30DRSLIIS 2011
E30DRINA, E30DRLINA, E30DRSINC, E30DRSLINC 2012
E30DRISC, E30DRLISC 2010
E30DRLSES, E30DRSES 2009
E30DTELAAA, E30DTELAAB, E30TESLAAA, E30TESLAAB 2012
E30DTELIIH, E30DTELIIR, E30TESLIIH, E30TESLIIS 2011
E30DTELINA, E30TESLINC 2012
E30DTELISC 2010
E30DTELSES 2009
E30DTLAAA, E30DTSLAAA 2012
E30DTLAAB, E30DTSLAAB 2012
E30DTLIIH, E30DTLIIR, E30DTSLIIH, E30DTSLIIS 2011
E30DTLINA, E30DTSLINC 2012
E30DTLISC 2010
E30DTLSES 2009

Information:


TIMING MARKS2. Remove the plug from the timing pin hole in fuel injection pump housing and install timing pin (1).
TIMING PIN INSTALLED
1. FT887 Timing Pin (Fabricated Tool).3. Remove bolts (2) and tachometer drive assembly (3) from the fuel injection pump camshaft.4. Remove the drive gear (4) from the fuel injection pump camshaft.
PUMP DRIVE GEAR (Typical Example)
2. Bolts (three). 3. Tachometer drive assembly. 4. Drive gear.5. Remove retaining screw (5), washer (6), and small outer camshaft gear (7) from the engine camshaft.
CAMSHAFT GEAR
5. Retaining screw. 6. Washer. 7. Small outer camshaft gear.
REMOVING GEAR (Typical Example)
8. 1P2321 Puller. 9. 8S5579 Spacer. 10. 9S9155 Spacer.6. Install puller (8), with spacer (9) over the shaft in the camshaft and spacer (10) on spacer (9) as shown and remove the gear from the camshaft.Install Camshaft Gear
1. Heat the gear to a temperature of approximately 400° F (204° C) before installing on the camshaft.
Do not heat the gear with a torch. Do not heat the gear to a temperature of more than 600° F (315° C). Heating the gear with a torch or to a temperature of more than 600° F (315° C) may cause the two drive dowels for the timing gear to loosen and come out of the gear.
2. Align slot in gear hub with the pin in the camshaft. Install the gear on the camshaft with timing mark on gear aligned with timing mark on crankshaft gear. Be sure the gear is completely seated against the shoulder of the camshaft.
TIMING MARKS
Do not drive the gear on the camshaft. Serious damage can result to camshaft or camshaft thrust pin.
3. Align holes in small gear with dowels in large gear and install the small gear.4. Align pin (11) in washer (6) with hole (12) in camshaft and install washer (6).
INSTALLING WASHER (Typical Example)
6. Washer. 11. Pin. 12. Hole.5. Install retaining screw (5) and tighten to 108 36 lb. in. (124.5 41.5 cm.kg). Stake screw (5) in two places.
Stake retaining screw (5) carefully. Heavy blows on washer or retaining screw can force the shaft extension too far into the camshaft and eliminate all end clearance.
STAKING SCREW (Typical Example)
5. Retaining screw.6. After retaining screw (5) is staked, the gear requires .003 to .027 in. (0.08 to 0.69 mm) end clearance to prevent binding against the washer, camshaft end, or camshaft gear.7. Put timing plate (14) on the engine and thread bolt (13) into the timing gear.
TIMING PLATE INSTALLED (Typical Example)
13. Bolt. 14. 5P950 Timing Plate.8. Install drive gear (4) on the fuel injection pump camshaft with the holes in the position shown and the part number facing out. To be able to advance the timing adjustment without removing the front cover, position gear (4) in the direction of the arrow so the bolt holes in the fuel injection pump camshaft are off center as shown. The bolts must thread freely into the holes in the fuel injection pump camshaft.
GEAR INSTALLED
4. Drive gear.9. Install tachometer drive assembly (3) and tighten finger tight.
PUMP DRIVE GEAR INSTALLED
2. Bolts (three). 3. Tachometer drive assembly. 4. Pump drive gear.10. Install bolts (2) and tighten the bolts to 32 5 lb. ft. (4.4 0.7 mkg). Tighten the tachometer drive assembly (3) to 50 10 lb. ft. (6.9 1.4 mkg).11. Remove the timing pin from the fuel injection pump housing and install the plug in the timing hole.


Parts steering EVINRUDE:

0173699
 
0173699 STEERING CONNECTOR KIT, Stainless steel
BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SREDA, BE25ARECA, BE25AREDC, BE25AREUR, BE25BAEDR, BE25EECE, BE25EEDM, BE25EEUB, BE30BAEDE, BE30EECS, BE30EEDE, BE30EEUD, BE35ARECR, BE35AREDS, BE35AREEA, BE35AREUC, BE35ARSIB, BE35ARSSM, BE40EECR, BE40EEDS, BE40E
Back to top