0335892 EVINRUDE STERN BRACKET ASSY., Stbd.


0335892 STERN BRACKET ASSY., Stbd. EVINRUDE BE4RDHEDS, BE5DREDS, BE5DREUC, BE5FRBECC, BE5FRBEUS, BE6DRECR, BE6DREDS, BE6DREUC, BE8RCB, BE8RCH, BE8RCLT, BE8REDS, E4RDHENM, E4RDHEOD, E4RDHERE, E4RDHETB, E5DRECR, E5R4EEM, E5R4EEM, E5R4SIE, E5R4SIE, E5R4SSB, E5R4SSB, E6R4EEM, E6R4SIE, E6R4SSB, E6R STERN
0335892 STERN BRACKET ASSY., Stbd. EVINRUDE
Rating:
19

Buy STERN BRACKET ASSY., Stbd. 0335892 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 15
 

BRP EVINRUDE entire parts catalog list:

BE4RDHEDS, BE4RDHLEDS 1996
BE5DREDS, BE5DRLEDS 1996
BE5DREUC, BE5DRLEUC 1997
BE5FRBECC, BE5FRBLECC, HE5FRECA, HE5FRLECA 1998
BE5FRBEUS, BE5FRBLEUS, HE5FREUR, HE5FRLEUR 1997
BE6DRECR, BE6DRLECR, E6RECR, E6RLECR 1998
BE6DREDS, BE6DRLEDS, BE6REDS, BE6RLEDS, E6REDS, E6RLEDS, E6SLEDS 1996
BE6DREUC, BE6DRLEUC, E6REUC, E6RLEUC 1997
BE8RCB, BE8RCLB 1997
BE8RCH, BE8RCLH 1996
BE8RCLT, BE8RCT 1998
BE8REDS, BE8RLEDS, BE8SRLEDS, E8REDS, E8RLEDS, E8SRLEDS 1996
E4RDHENM, E4RDHLENM 1992
E4RDHEOD, E4RDHLEOD 1995
E4RDHERE, E4RDHLERE 1994
E4RDHETB, E4RDHLETB 1993
E5DRECR, E5DRLECR 1998
E5R4EEM, E5RB4EER, E5RBL4EER, E5RL4EEM, E6R4EEM, E6RL4EEM 1999
E5R4EEM, E5RB4EER, E5RBL4EER, E5RL4EEM 1999
E5R4SIE, E5RL4SIE, E6R4SIE, E6RL4SIE 2001
E5R4SIE, E5RL4SIE 2001
E5R4SSB, E5RL4SSB, E6R4SSB, E6RL4SSB 2000
E5R4SSB, E5RL4SSB 2000
E6R4EEM, E6RL4EEM 1999
E6R4SIE, E6RL4SIE 2001
E6R4SSB, E6RL4SSB 2000
E6REIA, E6RLEIA, E6SLEIA 1991
E6RENM, E6RLENM, E6SLENM 1992
E6REOD, E6RLEOD, E6SLEOD 1995
E6RERE, E6RLERE, E6SLERE 1994
E6RETB, E6RLETB, E6SLETB 1993
E8DREEA 1999
E8DRSSM 2000
E8RECR, E8RLECR, E8SRLECA 1998
E8REIA, E8RLEIA, E8SRLEIA 1991
E8RENM, E8RLENM, E8SRLENM 1992
E8REOD, E8RLEOD, E8SRLEOD 1995
E8RERE, E8RLERE, E8SRLERE 1994
E8RETB, E8RLETB, E8SRLETB 1993
E8REUC, E8RLEUC, E8SRLEUC 1997
E8WREES, E8WRLEES 1999
E8WRLSIR, E8WRSIR 2001
E8WRLSSC, E8WRSSC 2000
HE6FRECA, HE6FRLECA 1998
HE6FREUR, HE6FRLEUR 1997

Information:

start by: a) remove fuel injection pump housing and governor as a unitb) remove governorc) remove variable timing unit1. Remove the cover from the front of the fuel injection pump housing.2. Put identification on each of the fuel injection pumps by its location in the fuel injection pump housing. 3. Loosen the fuel injection pumps by using tool (A).
The fuel rack must be held in the center position while removing pumps.
4. Remove fuel injection pumps (1) by using tool (B).
When disassembling the fuel injection pumps, use caution to prevent damage to plunger surfaces. Do not mix the body and plunger assemblies of one pump with the body and plunger assemblies of another pump.
5. Disassemble the fuel injection pump as follows: Remove retainer ring (9), washer (2), bonnet (3), check valve (5), spring (4). Remove plunger (7). Remove pin (12) to remove sleeve (8). Remove spring (6) and washer (11). Remove barrel (10). 6. Remove cover (14), spring (16), and pin (15) for fuel rack centering.7. Remove cover (13) for the position indicator of the fuel rack. 8. Remove the fuel rack (20) from the front of the housing. 9. Put identification on each lifter by its location in the housing. Remove the lifters (22).
Do not remove or install new spacers in the lifters. A spacer that is not correctly assembled can cause engine failure. Spacers and lifters must also be installed in their original locations.
10. Remove two bolts (24) and plate (23) that holds the camshaft in the housing. Remove camshaft.11. Remove camshaft bearing using tool (C).12. Remove the rack bearing (21). 13. Remove the variable timing bearing (25) with tooling (D). 14. Remove the sleeve (26) from the housing with tooling (E).15. Remove two bolts (17), pin (18) and spacer (19).Assemble Fuel Injection Pump Housing
1. Heat sleeve (1) in oil to a maximum temperature of 275°F (135°C) and install it on the housing.2. Install the variable timing bearing with tooling (A). When installing, put the hole in the bearing in alignment with the hole in the housing.3. Install the two rack bearings. 4. Install the camshaft bearings using tool (B). Install the rear bearings .010 .005 in. (0.25 0.13 mm) inside the rear face of the bearing bore. Install the front bearing .015 .005 in. (0.25 0.13 mm) inside the front face of the housing. When installing, put the holes in the camshaft bearings in alignment with the holes in the bores in the housing. 5. Put clean engine oil on the camshaft and install it in the housing.6. Put the plate that holds the camshaft in position on the housing and install the lock and bolts.7. Install the lifters in their respective locations in the housing.8. Put clean fuel oil on the rack and install it in the housing. If new lifters and pumps are to be installed the fuel injection pump must be put in time. See FUEL INJECTION PUMP TIMING DIMENSION SETTING OFF ENGINE in TESTING AND ADJUSTING.9. Install the spacer and timing pin in the housing. Move the rack backward and forward until the timing pin is engaged in the groove in the rack.
Do not install fuel injection pumps if rack is not in the correct position.
10. Install the lever and cover (2) for the rack position indicator.11. Install the spring (5), pin (4), and cover (3) for getting center position of fuel rack.12. Put clean fuel oil on all parts of the fuel pumps and assemble as follows: Assemble barrel (8), washer (15) and spring (14). Install plunger (9) in barrel. Install sleeve (10) on plunger and install pin (16) in sleeve. Install check valve (7), and spring (6) in barrel. Install bonnet (12) and ring (13) on the bonnet. Install washer (11) on bonnet. Put pumps in their respective locations with tool (C). For installation of pumps, see REMOVING AND INSTALLING FUEL INJECTION PUMP ASSEMBLIES in TESTING AND ADJUSTING.13. Install felt washers around the fuel pump openings.14. Install the cover on the front of the housing for fuel injection pump.end by: a) install variable timing unitb) install governorc) install fuel injection pump housing and governor as a unit


Parts stern EVINRUDE:

0335891
 
0335891 STERN BRKT. ASSY., Port
BE4RDHEDS, BE5DREDS, BE5DREUC, BE5FRBECC, BE5FRBEUS, BE6DRECR, BE6DREDS, BE6DREUC, BE8RCB, BE8RCH, BE8RCLT, BE8REDS, E4RDHEIA, E4RDHENM, E4RDHEOD, E4RDHERE, E4RDHETB, E5DRECR, E5R4EEM, E5R4EEM, E5R4SIE, E5R4SIE, E5R4SSB, E5R4SSB, E6R4EEM, E6R4SIE, E6
Back to top