0352370 EVINRUDE STRAP


0352370 STRAP EVINRUDE E55MJRLAAA, E55MJRLIIM, E55MJRLINB, E55MJRLISA, E55MJRLSCC, E55MJRLSEF, E55MJRLSER, E55MRLAAA, E55MRLIIM, E55MRLINB, E55MRLISA, E55MRLSCC, E55MRLSEF, E55MRLSER STRAP
0352370 STRAP EVINRUDE
Rating:
78

Buy STRAP 0352370 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

BRP EVINRUDE entire parts catalog list:

E55MJRLAAA 2012
E55MJRLIIM 2011
E55MJRLINB 2012
E55MJRLISA 2010
E55MJRLSCC 2008
E55MJRLSEF 2009
E55MJRLSER 2009
E55MRLAAA 2012
E55MRLIIM 2011
E55MRLINB 2012
E55MRLISA 2010
E55MRLSCC 2008
E55MRLSEF 2009
E55MRLSER 2009

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     6V-6640     Sealant     1    
B     -     Guide Bolt
M8 by 40 mm     2    
C     319-6486     Alignment Tool     1    
- Bolts
M10 by 50 mm     3    
D     1U-6396     O-Ring Assembly Compound     1    
E     7M-7456     Bearing Mount Compound     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the front housing is clean and free from damage. If necessary, replace the front housing.If necessary, install blanking plugs to a new front housing. Use Tooling (A) in order to seal all D-plugs.
Clean all the gasket surfaces of the cylinder block.
Illustration 1 g02201113
Illustration 2 g02201114
Inspect dowel (13) and dowel (14) for damage. If necessary, replace the dowels in the cylinder block.
Install thrust washer (12) into the recess in the cylinder block. Refer to Disassembly and Assembly, "Camshaft - Install" for more information.
Install Tooling (B) to the cylinder block. Refer to Illustration 2.
Align a new gasket (11) with Tooling (B) . Install the gasket to the cylinder block.Note: Ensure that two circular Tabs (X) on the gasket are engaged in two Holes (Y) in the cylinder block. Ensure that dowel (14) in the cylinder block is engaged on the gasket.
Install Tooling (C) to the cylinder block.
Illustration 3 g02201115
If necessary, follow Step 8.a through Step 8.c in order to install bearing (7) to housing (4) .
Apply a small continuous bead of Tooling (E) to outer Surface (Z) of bearing (7) .
Place housing (4) onto a suitable support.
Use a suitable tool in order to press bearing (7) into housing (3) until the bearing is in the correct position within the housing. Remove any excess bearing mount compound.
Install the front housing over Tooling (B) and Tooling (C) onto the cylinder block.
Illustration 4 g02201116
(8) M8 by 20 mm (9) M8 by 35 mm (10) M8 by 25 mm
Install new bolts (10) to front housing (3) hand tight.
Remove Tooling (B) .
Loosely install bolts (8) and bolts (9) finger tight. Refer to Illustration 4 for the correct position of the bolts.
Illustration 5 g02058297
Tighten bolts (8) , bolts (9) and bolts (10) in the sequence that is shown in Illustration 5 to a torque of 28 N m (248 lb in).
Remove Tooling (C) from the cylinder block.
Illustration 6 g02198874
Install new O-ring seal (5) and O-ring seal (6) to bypass tube (1) . Use Tooling (D) in order to lubricate the O-ring seals.
Install bypass tube (1) to the cylinder head. Install bolts (3) . Tighten the bolts to a torque of 9 N m (80 lb in).
Install a new cable strap (2) to wiring harness assembly.End By:
Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install" for the correct procedure.
Install the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) - Install" for the correct procedure.
If the engine has an accessory drive, install the accessory drive. Refer to Disassembly and Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
Install the engine oil pan plate . Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove" for the correct procedure.
Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Install" for the correct procedure.
Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install" for the correct procedure.
Install the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the correct procedure.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Fill" for the correct procedure.


Parts strap EVINRUDE:

0352845
 
0352845 STRAP
E55MJRLAAA, E55MJRLIIM, E55MJRLINB, E55MJRLISA, E55MJRLSCC, E55MJRLSEF, E55MJRLSER, E55MRLAAA, E55MRLIIM, E55MRLINB, E55MRLISA, E55MRLSCC, E55MRLSEF, E55MRLSER
0354615
 
0354615 STRAP, Upper coil mounting
E55MJRLAAA, E55MJRLIIM, E55MJRLINB, E55MJRLISA, E55MJRLSEF, E55MRLAAA, E55MRLIIM, E55MRLINB, E55MRLISA, E55MRLSEF
Back to top