0329498 SUPPORT, Tilt lock bracket, starboard EVINRUDE
E20CRCCA, E20CRCDC, E20CRCEM, E20CRCOS, E20CRCUR, E20CREIE, E20CREND, E20CRESB, E25ECCM, E25ECDR, E25ECOC, E25ECRS, E25ECUA, E25RCEM, E25REIE, E25REND, E25RESB, E25RWCDC, E25RWCOS, E25RWCRD, E25RWCUR, E25RWEIM, E25RWENB, E25RWESA, E25RWK, E25TECEM, E
SUPPORT
Price: query
Rating:
Compatible models:
E20CRCCA
E20CRCDC
E20CRCEM
E20CRCOS
E20CRCUR
E20CREIE
E20CREND
E20CRESB
E25ECCM
E25ECDR
E25ECOC
E25ECRS
E25ECUA
E25RCEM
E25REIE
E25REND
E25RESB
E25RWCDC
E25RWCOS
E25RWCRD
E25RWCUR
E25RWEIM
E25RWENB
E25RWESA
E25RWK
E25TECEM
E25TEEIE
E25TEEND
E25TEESB
E30RCED
E30REIC
E30RENR
E30RESS
E30TECED
E30TEEIC
E30TEENR
E30TEESS
E35RCED
E35REIC
E35RENR
E35RESS
U25RWA
EVINRUDE
BRP EVINRUDE entire parts catalog list:
E20CRCDC, E20CRLCDC, E20ECDC, E20ELCDC, E20TECDC 1986
E20CRCEM, E20CRLCEM, TE20CRCEM, TE20CRLCEM, TE20CRLESF 1989
E20CRCOS, E20CRLCOS, E20ECOS, E20ELCOS 1985
E20CRCUR, E20CRLCUR, E20ECUR, E20ELCUR 1987
E20CREIE, E20CRLEIE, TE20CRLEIE 1991
E20CREND, E20CRLEND, TE20CREND, TE20CRLEND 1992
E20CRESB, E20CRLESB, TE20CRESB, TE20CRLESB 1990
E25ECCM, E25ELCCM, E25RCCA, E25RLCCA, E25TECCA, E25TELCCA 1988
E25ECDR, E25ELCDR, E25RCDC, E25RLCDC, E25TECDC, E25TELCDC 1986
E25ECOC, E25ELCOC, E25RCOS, E25RLCOS, E25TECOS, E25TELCOS 1985
E25ECRS, E25ELCRS, E25RCRD, E25RLCRD, E25TECRD, E25TELCRD 1984
E25ECUA, E25ELCUA, E25RCUR, E25RLCUR, E25TECUR, E25TELCUR 1987
E25RCEM, E25RLCEM 1989
E25REIE, E25RLEIE, VE25REIE 1991
E25REND, E25RLEND 1992
E25RESB, E25RLESB, VE25RESB 1990
E25RWCDC, E25RWLCDC 1986
E25RWCOS, E25RWLCOS 1985
E25RWCRD, E25RWLCRD 1984
E25RWCUR, E25RWLCUR 1987
E25RWEIM, E25RWLEIM 1991
E25RWENB, E25RWLENB 1992
E25RWESA, E25RWLESA 1990
E25RWK, E25RWLK 1989
E25TECEM, E25TELCEM 1989
E25TEEIE, E25TELEIE 1991
E25TEEND, E25TELEND 1992
E25TEESB, E25TELESB 1990
E30RCED, E30RLCED 1989
E30REIC, E30RLEIC 1991
E30RENR, E30RLENR 1992
E30RESS, E30RLESS 1990
E30TECED, E30TELCED 1989
E30TEEIC, E30TELEIC 1991
E30TEENR, E30TELENR 1992
E30TEESS, E30TELESS 1990
E35RCED, E35RLCED 1989
E35REIC, E35RLEIC 1991
E35RENR, E35RLENR 1992
E35RESS, E35RLESS 1990
U25RWA, U25RWLA 1988
Information:
Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Note: Plug or cap all open ports with new plugs or caps.
Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Coolant - Change" for the correct procedure.
Illustration 1 g06484175
Typical example
Disconnect the Original Equipment Manufacturer (OEM) harness assembly from engine harness connector (6).
Remove nut and washer (5) from harness assembly (14). Remove bolts (3) from bracket (4). Remove the engine wiring harness assembly (14) from bracket (4). Position the harness assembly away from the bracket (2).
Cut cable strap (13), and cable strap (15) from harness assembly (1) for temperature sensor (12). Disconnect the harness assembly from the engine wiring harness.
Remove bolts (9) from bracket assembly (2). Remove the bracket assembly.
Loosen hose clamp (8) and move the clamp along hose assembly (10) away from elbow connection (7) for the Nitrogen Oxide Reduction System (NRS) cooler assembly. Disconnect the hose assembly from the elbow connection.Note: Note the hose clamp positions for installation purposes.
If necessary, loosen hose clamp (11) and move the clamp along hose assembly (10) away from the cylinder head. Disconnect the hose assembly from the cylinder head connection.
Illustration 2 g06484177
Typical example
Illustration 3 g06484179
Typical example
Remove bolts (17) from exhaust cooler assembly (16).
Disconnect harness assembly (21) from the NRS Valve (20).
Disconnect the OEM hose assembly from connection cooling system air vent (24)
Cut cable strap (22) for the engine harness assembly.
Remove bolt (28) and nuts (26) from exhaust cooler assembly (16).
Remove exhaust cooler assembly (16) from the cylinder head (23) and inlet elbow (19). Remove gasket (27) (not shown) and gasket (18) (not shown).
If necessary, remove studs (25) from cylinder head (23).Note: Note positions for installation purposes only.Installation Procedure
Check all components for wear and damage. If necessary, replace any components that are worn or damaged.Note: Remove plugs and caps that were previously installed prior to assembly.
Ensure that the NRS exhaust cooler is free from restriction and external damage. Ensure that the NRS exhaust cooler and tube assemblies are free from wear and damage. Refer to Systems Operation Testing and Adjusting, "Exhaust Cooler (NRS) - Test" for the correct inspection procedure.Note: The NRS exhaust cooler, should not be internally cleaned.
Illustration 4 g06484177
Typical example
Illustration 5 g06484179
Typical example
Illustration 6 g06484242
Tightening sequence for exhaust cooler assembly
If necessary, install studs (25) in the positions noted on removal.
Tighten the studs to a torque of 15 N m (133 lb in).
Position new gasket (27) (not shown) onto the cylinder head (23). Ensure that the gasket is correctly orientated and is correctly installed onto the studs.
Install new gasket (18) (not shown) onto exhaust cooler assembly (16). Ensure that the gasket is correctly positioned onto the exhaust cooler assembly.
Position exhaust cooler assembly (16) onto the cylinder head (23) and inlet elbow connection (19).
Install bolts (17) to exhaust cooler assembly (16). Hand tighten the bolts. Refer to Illustration 4
Install bolt (28) and nuts (26), to exhaust cooler assembly (16). Hand tighten the bolt and nuts. Refer to Illustration 5.
Tighten bolts (17) and bolt (20), nuts (30), to a torque of 22 N m (195 lb in) in the sequence shown in Illustration 6.
Connect harness assembly (21) to NRS Valve (20).
Install new cable strap (22) to the engine harness assembly.Note: Ensure that the cable strap meets the Original Equipment Manufacturer (OEM) specification.
Connect the OEM hose assembly to the connection cooling system air vent (24).
Illustration 7 g06484175
Typical example
Position new hose clamp (8) and new hose clamp (11) onto hose (10).Note: Ensure that the new hose clamps are correctly orientated.
Connect hose assembly (10) to elbow connection (7) and the cylinder head connection.
Position new hose clamp (8) and move the clamp along hose assembly (10) towards the exhaust cooler assembly. Ensure that the clip is correctly positioned onto the hose assembly.
Tighten the new hose clamp to a torque of 4.5 N m (40 lb in).
Position new hose clamp (11) and move the clamp along hose assembly (10) towards the cylinder head connection. Ensure that the clip is correctly positioned onto the hose assem
Parts support EVINRUDE:
0312191
0312191 SUPPORT,Indicator
100193A, 100293R, 100882B, 100990S, 10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 15404G, 15504C, 15604A, 18002C,
0322102
0322102 SUPPORT,Armature plate
10724A, 10824M, 10924B, 25702H, 25802C, 25904R, BE10EEDD, BE10RELEUS, BE15EEDS, BE15RELEUC, E10ECCD, E10ECDB, E10ECES, E10ECOM, E10ECSE, E10ECUE, E10EECC, E10EEIR, E10EENA, E10EEOE, E10EERB, E10EESC, E10EETM, E10ELCID, E10ELCNS, E10ELCRA, E10ELCTC, E