0398309 EVINRUDE SWIVEL BRACKET


0398309 SWIVEL BRACKET EVINRUDE C155WTLM, E100STLCCA, E100WTLCUA, E110MLCCA, E110MLCUR, E120TLCCA, E120TLCUR, E140CXCCS, E140TLCUA, E150CXCCA, E150TLCUR, E155WTLCUA, E175STLCCM, E175TLCUA, E88MSLCCC, E88MSLCCC, E90MLCUR, W100WTLM SWIVEL
0398309 SWIVEL BRACKET EVINRUDE
Rating:
93

Buy SWIVEL BRACKET 0398309 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$2,032.66
 

02-09-2022

-: -
K&M 039-8309 Ultra Leather KM Seats Legacy Silver, Gray Leather
Durable microfibers cloth or ultra leather covering || Standard air parallelogram suspension || Fully reclining backrest || EVC cushion comfort system to reduce vibration and fatigue while enhancing comfort || Fold-up armrests with E-Z Adjust Turn Wheel
Number on catalog scheme: 1
 

BRP EVINRUDE entire parts catalog list:

C155WTLM, C155WTXM 1988
E100STLCCA 1988
E100WTLCUA, E100WTXCUA 1987
E110MLCCA, E110TLCCA, E110TXCCA 1988
E110MLCUR, E110TLCUR, E110TXCUR 1987
E120TLCCA, E120TXCCA 1988
E120TLCUR, E120TXCUR 1987
E140CXCCS, E140TLCCM, E140TXCCM 1988
E140TLCUA, E140TXCUA 1987
E150CXCCA, E150TLCCA, E150TXCCA 1988
E150TLCUR, E150TXCUR 1987
E155WTLCUA, E155WTXCUA 1987
E175STLCCM, E175TLCCM, E175TXCCM 1988
E175TLCUA, E175TXCUA 1987
E88MSLCCC, VE88MSLCCC 1988
E88MSLCCC, E90TLCCA 1988
E90MLCUR, E90TLCUR 1987
W100WTLM, W100WTXM 1988

Information:


Table 1
Diagnostic Trouble Code for Intake Manifold Air Pressure Is High
J1939 Code Code Description Comments
102-16 Engine Intake Manifold #1 Pressure : High - moderate severity (2) This pressure is a variable value that is calculated by the ECM. The resulting value depends on the operating conditions of the engine. Probable Causes
Turbocharger electronic wastegate regulatorRecommended Actions
Table 2
Troubleshooting Test Steps Values Results
1. Download Information Using the Electronic Service Tool
A. Use the electronic service tool to download the "Product Status Report" (PSR) with histograms before performing any troubleshooting or clearing any diagnostic codes.
Note: The downloaded information will be required by the Dealer Solutions Network (DSN) if troubleshooting assistance is required.
Downloaded information
Result: The information was successfully saved.
Proceed to Test Step 2.
Result: The electronic service tool information was not successfully saved.
Contact the Dealer Solutions Network (DSN) for guidance.
2. Create an Electronic Service Tool Snapshot
A. Select "Snapshot Viewer" on the electronic service tool, using menus: Information -> Snapshot -> Viewer
B. Select the event code and then click "View Graph".
C. Select the following parameter and then click OK.
Engine Speed
D. Select Save to "File to save" a Snapshot File (*.xml). This file will contain all the data in the snapshot and not only the data shown on the graph.
Note: The downloaded information will be required by the DSN if troubleshooting assistance is required.
Snapshot saved
Result: The electronic service tool snapshot was successfully saved.
Proceed to Test Step 3.
Result: The electronic service tool snapshot was not successfully saved.
Contact the DSN for guidance.
3. Turbocharger Electronic Wastegate Regulator
A. Use the electronic service tool to perform the "Air System Motor Valves Verification Test" to check that the turbocharger wastegate is operating correctly.
B. Inspect the turbocharger. Refer to Systems Operation, Testing and Adjusting, "Turbocharger - Inspect".
Turbocharger wastegate
Result: Diagnostic codes became active during the "Air System Motor Valves Verification Test"
Repair: Troubleshoot the diagnostic codes. Refer to Troubleshooting, Diagnostic Trouble Codes.
If the wastegate is not operating correctly, disconnect the linkage from the actuator by removing the circlips. Check the crank on the turbine housing for free movement. If the crank moves freely, replace the wastegate actuator.
If the turbocharger wastegate is replaced, use the electronic service tool to perform the "Turbocharger Wastegate Actuator Replacement Reset".
Use the electronic service tool to perform the "Air System Motor Valve Verification Test" to verify that the repair eliminates the fault.
If the crank does not move freely, replace the turbocharger assembly. Refer to Disassembly and Assembly , Turbocharger - Remove and Disassembly and Assembly , Turbocharger - Install.
If the turbocharger is replaced, use the electronic service tool to perform the "Turbocharger Wastegate Actuator Replacement Reset".
Use the electronic service tool to perform the "Air System Motor Valve Verification Test" to verify that the repair eliminates the fault.
Result: There is a suspected fault in the wastegate or the wastegate actuator.
Repair: Replace the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove" and Disassembly and Assembly, "Turbocharger - Install".
If the turbocharger is replaced, use the electronic service tool to perform the "Turbocharger Wastegate Actuator Replacement Reset".
Use the electronic service tool to perform the "Air System Motor Valve Verification Test"
Result: The wastegate and the wastegate actuator operate correctly.
If the fault is still present, contact the DSN and provide the following information from Test Step 1 and Test Step 2:
• PSR and Histograms
• Snapshot data


Parts swivel EVINRUDE:

0397743
 
0397743 SWIVEL BRACKET
E100WTLCUA, E110MLCUR, E120TLCUR, E140TLCUA, E150STLCUR, E150TLCUR, E155WTLCUA, E175TLCUA, E88MSLCUS, E88MSLCUS, E90MLCUR
0398935
 
0398935 SWIVEL BRACKET
C155WTLM, E100STLCCA, E110MLCCA, E120TLCCA, E140CXCCS, E150CXCCA, E150STLCCA, E175STLCCM, E88MSLCCC, E88MSLCCC, W100WTLM
Back to top