0434024 EVINRUDE SWIVEL BRACKET ASSY.


0434024 SWIVEL BRACKET ASSY. EVINRUDE BE4RDHEDS, BE5DREDS, BE5DREUC, BE6DRECR, BE6DREDS, BE6DREUC, BE8RCB, BE8RCH, BE8RCLT, BE8REDS, E4RDHEIA, E4RDHENM, E4RDHEOD, E4RDHERE, E4RDHETB, E5DRECR, E6REIA, E6RENM, E6REOD, E6RERE, E6RETB, E8DREEA, E8DRSSM, E8RECR, E8REIA, E8RENM, E8REOD, E8RERE SWIVEL
0434024 SWIVEL BRACKET ASSY. EVINRUDE
Rating:
23

Buy SWIVEL BRACKET ASSY. 0434024 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 34
 

BRP EVINRUDE entire parts catalog list:

BE4RDHEDS, BE4RDHLEDS 1996
BE5DREDS, BE5DRLEDS 1996
BE5DREUC, BE5DRLEUC 1997
BE6DRECR, BE6DRLECR, E6RECR, E6RLECR 1998
BE6DREDS, BE6DRLEDS, BE6REDS, BE6RLEDS, E6REDS, E6RLEDS, E6SLEDS 1996
BE6DREUC, BE6DRLEUC, E6REUC, E6RLEUC 1997
BE8RCB, BE8RCLB 1997
BE8RCH, BE8RCLH 1996
BE8RCLT, BE8RCT 1998
BE8REDS, BE8RLEDS, BE8SRLEDS, E8REDS, E8RLEDS, E8SRLEDS 1996
E4RDHEIA, E4RDHLEIA 1991
E4RDHENM, E4RDHLENM 1992
E4RDHEOD, E4RDHLEOD 1995
E4RDHERE, E4RDHLERE 1994
E4RDHETB, E4RDHLETB 1993
E5DRECR, E5DRLECR 1998
E6REIA, E6RLEIA, E6SLEIA 1991
E6RENM, E6RLENM, E6SLENM 1992
E6REOD, E6RLEOD, E6SLEOD 1995
E6RERE, E6RLERE, E6SLERE 1994
E6RETB, E6RLETB, E6SLETB 1993
E8DREEA 1999
E8DRSSM 2000
E8RECR, E8RLECR, E8SRLECA 1998
E8REIA, E8RLEIA, E8SRLEIA 1991
E8RENM, E8RLENM, E8SRLENM 1992
E8REOD, E8RLEOD, E8SRLEOD 1995
E8RERE, E8RLERE, E8SRLERE 1994
E8RETB, E8RLETB, E8SRLETB 1993
E8REUC, E8RLEUC, E8SRLEUC 1997
E8WREES, E8WRLEES 1999
E8WRLSIR, E8WRSIR 2001
E8WRLSSC, E8WRSSC 2000

Information:

3. Disconnect linkage (3) from the governor.4. Remove breather tube (2) from the machine.5. Remove fuel injection lines (1) from the fuel injection pumps and valves.
Put protection caps (5F2807) and plugs (2F2990) on the fuel injection pumps, valves and lines to keep dirt and foreign material out of the fuel system.
6. Remove all of bolts (4) and (5) that hold the fuel injection pump housing and governor in position. 7. Remove the fuel injection pump housing and governor as a unit from the machine.Install Fuel Injection Pump Housing And Governor
1. Make sure the No. 1 piston is on the TOP CENTER COMPRESSION POSITION for correct timing of the engine as follows: a) Remove the valve cover from the cylinder head.b) Remove the electric starting motor and timing hole plug from the front of the flywheel housing.c) Use tool group (C) to turn the crankshaft clockwise, as seen from the front of the engine. Turn the crankshaft until a 3/8"-16 NC bolt can be installed in the flywheel through the hole in the flywheel housing and the intake and exhaust valves for the No. 1 piston are closed. 2. Install tool (A) on the rear face of the accessory drive housing.3. If tool (A) can be installed with the dowels in the accessory drive housing in alignment with the dowel holes in tool (A), the accessory drive shaft is in correct timing. Go to Step 8. If tool (A) can not be installed, go to Step 4.4. Remove the small cover from the front of the timing gear cover. Remove the nut and washer that hold the drive gear to the accessory drive shaft. 5. Use tooling (B) to make a separation of the drive gear from the accessory drive shaft. Turn the accessory drive shaft until tool (A) can be installed.6. Install the washer (with the outside diameter of the washer in contact with the gear) and the nut to hold the drive gear to the accessory drive shaft. Tighten the nut to a torque of 100 10 lb.ft. (135 14 N m). 7. Install the cover and gasket on the front of the timing gear cover. Remove tool (A) from the accessory drive housing.8. Remove tool (A) and install the gasket on the accessory drive housing. Install the O-ring seals in the bracket that the fuel injection pump housing is installed on. Put clean oil on the O-ring seals. 9. Put the fuel injection pump housing and governor in position as a unit. Make sure the end of the accessory drive shaft is engaged in the groove (slot) in the fuel injection pump camshaft. Install all of bolts (4) and (5) to hold the fuel injection pump housing and governor in position.10. Remove all caps and plugs from the fuel lines and openings. Install fuel injection lines (1) and tighten the nuts to a torque of 30 5 lb.ft. (40 7 N m).11. Install breather tube (2).12. Connect control linkage (3) to the governor.13. Install the panel assembly on the left side of the machine.14. Turn the fuel valve at the bottom of the fuel tank to the "ON" position.15. Remove (bleed) the air from the fuel system.


Parts swivel EVINRUDE:

0337017
SWIVEL PLATE
0337017 SWIVEL PLATE
B25JREUR, BE10EEDD, BE10FAEDC, BE10FAEUR, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE15EEDS, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE15RELEUC, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20SREDA, BE20SREUM, BE25ARECA, BE25AREDC, BE25AREUR, BE25B
Back to top