0586105 TEMPERATURE SWITCH EVINRUDE
E65WELEES, E65WELSIR, E65WELSSC, SE65WMLD, SE65WMLM, SE65WMLZ2
TEMPERATURE
Price: query
Rating:
BRP EVINRUDE entire parts catalog list:
- CYLINDER & CRANKCASE » 0586105
E65WELSSC 2000
SE65WMLD, SE65WMYD 1998
SE65WMLM, SE65WMYM 1996
SE65WMLZ2, SE65WMYZ2 1997
Information:
Illustration 1 g00925182
Test Step 1. Check for Connector Damage
Turn BATTCB to the OFF position.
Turn the ECS to the OFF/RESET position.
Check connectors and associated wiring for the following problems: damage, corrosion, abrasion and incorrect attachment.Expected Result:The connectors and wiring should be free of the following problems: damage, corrosion, abrasion and incorrect attachment.Results:
OK - The connectors and wiring are free of problems. Proceed to test step 2.
Not OK - The connectors and wiring are not free of problems.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Stop.Test Step 2. Check the Status of the Switch.
Turn the circuit breaker for the battery to the ON position.
Turn the ECS to the STOP position.
Activate the emergency stop switch.
Connect the Caterpillar Electronic Technician (ET) to the service tool connector.
Observe the status of the emergency stop switch on the Cat ET.Expected Result:The parameter for the emergency stop switch should read "ON".Results:
OK - The parameter for the emergency stop switch displays "ON". The emergency stop switch is working correctly. Proceed to test step 3.
Not OK - The parameter for the emergency stop switch does not display "ON". Proceed to test step 4.Test Step 3. Check the Status of the Switch.
Deactivate the emergency stop switch.Expected Result:The parameter for the emergency stop switch should read "OFF".Results:
OK - The parameter for the emergency stop switch displays "OFF". The emergency stop switch is working correctly.Repair: The repair is complete. Stop.
Not OK - The parameter for the emergency stop switch does not display "OFF". Proceed to test step 4.Test Step 4. Test the ECM.
Turn the ECS to the OFF/RESET position.
Disconnect P1 from the ECM. Remove P1-29, P1-02 and P1-24.
Locate a suitable jumper wire.
Insert the jumper wire at P1. Connect P1-02 and P1-24 to P1-29.
Turn the ECS to the STOP position.
Observe the parameters for the emergency stop on the Cat ET.
Turn the ECS to the OFF/RESET position. Remove the jumper wire and reinstall all wires.Expected Result:The parameter for the emergency stop switch should display "ON" when the jumper is installed. The parameter for the emergency stop switch should display "OFF" when the jumper is removed.Results:
OK - The parameter for the emergency stop switch displays "ON". Proceed to test step 5.
Not OK - The parameter for the emergency stop switch does not display "ON".Repair: Replace the ECM. Perform a diagnostic functional test. Perform the diagnostic procedure Troubleshooting, "Replacing the ECM". Stop.Test Step 5. Check the Switches and the Wiring.
Turn the ECS to the OFF/RESET position.
Activate the emergency stop switch.
Measure the resistance between the digital sensor return P1-29 and the remote emergency stop switch 1 P1-02.
Measure the resistance between digital sensor return P1-29 and the remote emergency stop switch 2 P1-24.Expected Result:The resistance should be greater than 20,000 Ohms.Results:
OK - The resistance is greater than 20,000 Ohms. Proceed to test step 6.
Not OK - The resistance is less than 20,000 Ohm. There is a short circuit in the emergency stop switch.Repair: Repair the switch or wiring and/or replace the switch or wiring. Stop.Test Step 6. Deactivate the Switch.
Deactivate the emergency shutdown switch.
Measure the resistance between digital sensor return P1-29 and the remote emergency stop switch 1 P1-02.
Measure the resistance between the digital sensor return P1-29 and the remote emergency stop 2 P1-24.Expected Result:The resistance should read less than 10 Ohms.Results:
OK - The resistance is less than 10 Ohms. The emergency shutdown switch is OK.Repair: The repair is complete. Stop.
Not OK - The resistance is greater than 10 Ohms. There is an open circuit in the emergency shutdown switch.Repair: Repair the switch or wiring and/or replace the switch or wiring. Stop.