5040571 EVINRUDE THROTTLE ROD


5040571 THROTTLE ROD EVINRUDE B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4INS, B15TE4INS, E15PL4INS, E15R4INS THROTTLE
5040571 THROTTLE ROD EVINRUDE
Rating:
93

Buy THROTTLE ROD 5040571 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$12.15
 

13-11-2023
0.26[0.12] Pounds
-: -
DAYCO Poly Rib Belt
Material : EPDM, Aramid Reinforced || Developed through extensive laboratory and actual road mileage testing
Number on catalog scheme: 46
 

BRP EVINRUDE entire parts catalog list:

B15PL4AAA, B15PL4AAB, E15PL4AAA, E15PL4AAB 2012
B15PL4INS 2012
B15R4AAA, B15RL4AAA, E15R4AAA, E15RL4AAA 2012
B15R4AAB, B15RL4AAB, B15TE4AAA, B15TE4AAB, B15TEL4AAA, B15TEL4AAB, E15R4AAB, E15RL4AAB, E15TE4AAA, E15TE4AAB, E15TEL4AAA, E15TEL4AAB 2012
B15R4INS, E15RL4INS 2012
B15RL4INS, B15TEL4INS, E15TE4INS, E15TEL4INS 2012
B15TE4INS 2012
E15PL4INS 2012
E15R4INS 2012

Information:

2. Start the LEXT3037 PC Program, or Flash from Electronic Technician (ET).3. Select the engine Personality Module part number to be programmed into the ECM, and proceed with programming the Personality Module. The new ECM is shipped with a blank Personality Module.4. PC Program Personality Module Messages and Their Meaning are discussed below. A new ECM comes with a blank (previously unprogrammed) personality module. A blank personality module will prompt you for all three of the following messages. The information contained in the "ECM Status" will be scrambled and meaningless if the module has not been previously programmed (this is normal).- Message - "The engine ID in the flash file does not match the engine ID in the ECM."- Meaning - The ECM has a personality module in it for a different engine, for example, the ECM has a 3406E personality module in it, and you are attempting to program a 3176B personality module into it.- What you should do - Stop the transfer and access information about "ECM Status" under the "Electronic Control Module" menu. Make sure the file you are about to transfer is for the same engine it will be installed in.- Message - "The application ID in the flash file does not match the application ID in the ECM."- Meaning - The ECM has a personality module in it for a different application, for example, the ECM has a 3176B On-Highway Truck personality module in it, and you are attempting to program a 3176B Challenger personality module into it.- What you should do - Stop the transfer and access information about "ECM Status" under the "Electronic Control Module" menu. Make sure the file you are about to transfer is for the On-Highway Truck application.- Message - "The ECM ID in the flash file does not match the ECM ID in the ECM."- Meaning - The ECM is not for use in the 3176B, C-10, C-12, and 3406E On-Highway truck application.- What you should do - Stop the transfer and access information about "ECM Status" under the "Electronic Control Module" menu. Make sure the ECM on the engine is for a 3176B, C-10, C-12, and 3406E On-Highway truck application. If you access the "ECM Status" under the "Electronic Control Module" menu of the PC Program, but do not follow this information access by programming the Personality Module, you must turn the vehicle ignition key switch to the OFF position, and then to the ON position before using an ECAP or ET. If you do not cycle the key switch after reading the "ECM Status", the ECM will not communicate with your service tool, or start the engine. Cycling the key switch is not necessary following successful programming of a personality module using the Flash Designer Program.5. Start the engine and check for proper operation. - Program any parameters not previously in the old personality module if 253-02 Check Customer Or System Parameters (56) code is active. Read the code from the Active Diagnostic code screen of the ECAP or ET to determine the parameter(s) requiring programming.- Remember, on initial power up of a new ECM, five parameters (six for a 3406E) must be programmed to avoid a 253-02 Check Customer Or System Parameters (56) code. They are Full Load Setting (FLS), Full Torque Setting (FTS), Vehicle Speed Calibration (ppm), Rating Number and Engine Serial Number (and Injector Codes, 3406E only). If the ECM serial number does not end in "CG" or "CJ" and the ECM is flash programmed with a NOV95 Personality Module the Total Tattletale may change by a random value when a Customer Specified Parameter value is programmed. To correct this problem upgrade to AUG96 or later Personality Module.6. Clear / reset trip data. - Flash programming may cause the trip data to appear scrambled when viewed. After flash programming is complete reset the trip data before releasing the vehicle.


Parts throttle EVINRUDE:

5041345
 
5041345 THROTTLE CABLE
B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15R4AAA, B15R4AAB, B3R4AAA, E10TEL4AAB
5040263
 
5040263 THROTTLE ARM
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
5040284
 
5040284 THROTTLE FRICTION ARM
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
Back to top