0316028 THRUST WASHER, Shifter dog EVINRUDE
100193A, 115083D, 115983E, 125183C, 50172S, 50202C, 60072B, 60172C, 65272S, 85093B, 85193A, 85993E
THRUST
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- GEARCASE » 0316028
115983E, 115983S 1969
125183C 1971
50172S, 50173S 1971
50202C, 50203C, 50272C, 50273C 1972
60072B, 60072D, 60073B, 60073D 1970
60172C, 60172E, 60173C, 60173E 1971
65272S, 65273S 1972
85093B, 85093D 1970
85193A, 85193H 1971
85993E, 85993M, 85993S 1969
Information:
Start By:a. remove cylinder head *b. remove camshaft*The cylinder head must be off the engine to allow the cam bearing removal and installation tooling to be installed. 1. Remove the bolts and rear cover (1) from the cylinder head. Check the condition of O-ring seal (2). If O-ring seal (2) appears worn or damaged, use a new part for replacement. The procedure to remove the cam bearings is the same for each of the seven bearings. However, each bearing requires a different combination of tooling. 2. Remove cam bearing No. 7 (the rear cam bearing) as follows:a. Screw the 8M-8778 Stud into the 9U-7222 Cam Bearing Pilot. b. Insert the small diameter of Cam Bearing Pilot Tool (B) into the cam bearing as shown.c. Position Tooling (A) on the back of the cylinder head as shown. Note that the cylinder is rod retracted, and positioned against the cylinder head.d. Screw the 6V-4013 Threaded Rod into Tool (B). Install the 5P-8248 Washer and 2J-3506 Nut. Screw the 2J-3506 Nut on the 6V-4013 Threaded Rod until it contacts the cylinder. e. Actuate the hydraulic cylinder to remove the cam bearing from the cylinder head.f. Separate Tooling (B) from the 6V-4013 Threaded Rod. Remove the old cam bearing from Tooling (B).
Use the 9U-7223 Alignment Bushing when the 8S-8292 or 8S-8293 Extensions are attached to Tooling (B). The 9U-7223 Alignment Bushing will guide the extensions and help support weight of the tooling. Install 9U-7223 Alignment Bushing in the inside diameter of any cam bearing between the hydraulic cylinder and Tooling (B).
Example: Tooling (H) used to remove No. 1 camshaft bearing.3. Repeat Step 2 using Tooling (B) and:a. Tooling (C) to remove camshaft bearing No.6.b. Tooling (D) to remove camshaft bearing No.5.c. Tooling (E) to remove camshaft bearing No.4.d. Tooling (F) to remove camshaft bearing No.3.e. Tooling (G) to remove camshaft bearing No.2.f. Tooling (H) to remove camshaft bearing No.1 (front camshaft bearing).Install Camshaft Bearings
Make sure inside of the cylinder head is clean. Check the cam bores to make sure there are no burrs. Put a thin film of clean engine oil inside of the cam bearing bore and on each new camshaft bearing prior to installing.
The procedure to install the cam bearings is the same for each of the bearings. However, each bearing requires a different combination of tooling. The depth that the camshaft bearing is installed into the cam bore is controlled by the tooling. All bearing depths are the same EXCEPT for the No.1 camshaft bearing. Be sure to use the correct tooling when installing the camshaft bearings. 1. Do the following to install camshaft bearing No.7:a. Screw the 8M-8778 Stud into the 9U-7222 Cam Bearing Pilot.b. Install the camshaft bearing on the 9U-7222 Cam Bearing Pilot. Note the camshaft bearing fits over the small diameter of the 9U-7222 Cam Bearing Pilot, and is held in place by the 9U-7213 Backup Plate and OS-0509 Bolt. Make sure the 9U-7213 Backup Plate is positioned with the large chamfer contacting the camshaft bearing as shown.c. Insert the large diameter of cam bearing pilot Tool (B) into the cam bearing bore as shown. d. Attach Tooling (A) to Tooling (B) with the 6V-4013 Threaded Rod and 2J-3506 Nut. Screw the 2J-3506 Nut on the 6V-4013 Threaded Rod until it contacts the hydraulic cylinder. Note that the cylinder is rod retracted, and positioned against the cylinder head. e. Actuate the hydraulic cylinder to pull the camshaft bearing into the cam bore. When the chamfer of Tooling (B) contacts the cam bore face, the camshaft bearing is properly seated.f. Remove Tooling (A) from Tooling (B).h. Remove Tooling (B) from the No.7 camshaft bearing.
Example: Tooling (E) used to install the No.5 camshaft bearing.2. Repeat Step 1 using Tooling (B) and:a. Tooling (C) to install camshaft bearing No.6.b. Tooling (D) to install camshaft bearing No.5.c. Tooling (E) to install camshaft bearing No.4.d. Tooling (F) to install camshaft bearing No.3.e. Tooling (G) to install camshaft bearing No.2.
When installing camshaft bearing No.1, use the 9U-7214 Spacer Plate (Tool J) installed with Tooling (B) as described below. Tool (J) is used to seat the No.1 camshaft bearing to the correct depth in the cam bore.
3. Do the following steps to install No.1 camshaft bearing:a. Install the camshaft bearing on the small diameter of the 9U-7222 Cam Bearing Pilot. The 9U-7214 Spacer Plate is positioned against camshaft bearing (3), and held in place by the 9U-7213 Backup Plate and 0S-0509 Bolt. Make sure the 9U-7213 Backup Plate is positioned with the large chamfer contacting the 9U-7214 Spacer Plate.b. Insert the large diameter of cam bearing pilot Tool (B) into the No.1 cam bearing bore. c. Attach Tooling (B) and Tool (J) to Tooling (H). Actuate the hydraulic cylinder to pull the camshaft bearing into cam bore No.(1). When the chamfer of Tooling (B) contacts the cam bore face, the camshaft bearing is properly seated.d. Remove Tooling (H) from Tooling (B).e. Remove Tooling (B) from cam bearing No.1. 4. Install the bolts and rear cover (1) and O-ring seal (2) on the cylinder head.End By:a. install camshaftb. install cylinder head
Use the 9U-7223 Alignment Bushing when the 8S-8292 or 8S-8293 Extensions are attached to Tooling (B). The 9U-7223 Alignment Bushing will guide the extensions and help support weight of the tooling. Install 9U-7223 Alignment Bushing in the inside diameter of any cam bearing between the hydraulic cylinder and Tooling (B).
Example: Tooling (H) used to remove No. 1 camshaft bearing.3. Repeat Step 2 using Tooling (B) and:a. Tooling (C) to remove camshaft bearing No.6.b. Tooling (D) to remove camshaft bearing No.5.c. Tooling (E) to remove camshaft bearing No.4.d. Tooling (F) to remove camshaft bearing No.3.e. Tooling (G) to remove camshaft bearing No.2.f. Tooling (H) to remove camshaft bearing No.1 (front camshaft bearing).Install Camshaft Bearings
Make sure inside of the cylinder head is clean. Check the cam bores to make sure there are no burrs. Put a thin film of clean engine oil inside of the cam bearing bore and on each new camshaft bearing prior to installing.
The procedure to install the cam bearings is the same for each of the bearings. However, each bearing requires a different combination of tooling. The depth that the camshaft bearing is installed into the cam bore is controlled by the tooling. All bearing depths are the same EXCEPT for the No.1 camshaft bearing. Be sure to use the correct tooling when installing the camshaft bearings. 1. Do the following to install camshaft bearing No.7:a. Screw the 8M-8778 Stud into the 9U-7222 Cam Bearing Pilot.b. Install the camshaft bearing on the 9U-7222 Cam Bearing Pilot. Note the camshaft bearing fits over the small diameter of the 9U-7222 Cam Bearing Pilot, and is held in place by the 9U-7213 Backup Plate and OS-0509 Bolt. Make sure the 9U-7213 Backup Plate is positioned with the large chamfer contacting the camshaft bearing as shown.c. Insert the large diameter of cam bearing pilot Tool (B) into the cam bearing bore as shown. d. Attach Tooling (A) to Tooling (B) with the 6V-4013 Threaded Rod and 2J-3506 Nut. Screw the 2J-3506 Nut on the 6V-4013 Threaded Rod until it contacts the hydraulic cylinder. Note that the cylinder is rod retracted, and positioned against the cylinder head. e. Actuate the hydraulic cylinder to pull the camshaft bearing into the cam bore. When the chamfer of Tooling (B) contacts the cam bore face, the camshaft bearing is properly seated.f. Remove Tooling (A) from Tooling (B).h. Remove Tooling (B) from the No.7 camshaft bearing.
Example: Tooling (E) used to install the No.5 camshaft bearing.2. Repeat Step 1 using Tooling (B) and:a. Tooling (C) to install camshaft bearing No.6.b. Tooling (D) to install camshaft bearing No.5.c. Tooling (E) to install camshaft bearing No.4.d. Tooling (F) to install camshaft bearing No.3.e. Tooling (G) to install camshaft bearing No.2.
When installing camshaft bearing No.1, use the 9U-7214 Spacer Plate (Tool J) installed with Tooling (B) as described below. Tool (J) is used to seat the No.1 camshaft bearing to the correct depth in the cam bore.
3. Do the following steps to install No.1 camshaft bearing:a. Install the camshaft bearing on the small diameter of the 9U-7222 Cam Bearing Pilot. The 9U-7214 Spacer Plate is positioned against camshaft bearing (3), and held in place by the 9U-7213 Backup Plate and 0S-0509 Bolt. Make sure the 9U-7213 Backup Plate is positioned with the large chamfer contacting the 9U-7214 Spacer Plate.b. Insert the large diameter of cam bearing pilot Tool (B) into the No.1 cam bearing bore. c. Attach Tooling (B) and Tool (J) to Tooling (H). Actuate the hydraulic cylinder to pull the camshaft bearing into cam bore No.(1). When the chamfer of Tooling (B) contacts the cam bore face, the camshaft bearing is properly seated.d. Remove Tooling (H) from Tooling (B).e. Remove Tooling (B) from cam bearing No.1. 4. Install the bolts and rear cover (1) and O-ring seal (2) on the cylinder head.End By:a. install camshaftb. install cylinder head
Parts thrust EVINRUDE:
0313820
0313820 THRUST WASHER, Stern bracket to swivel
100193A, 100293R, 115083D, 115983E, 125183C, 125283R, 55872A, 55972A, 60072B, 60172C, 65372R, 70442M, 70572B, 70773S, 70873C, 70973R, 75542B, 75642D, 85093B, 85193A, 85293R, 85993E, E60ELCDS, E60ELCUC, E70ELCIH, E70ELCNB, E70ELCOS, E70ELCRD, E70ELCSA
0313427
0313427 THRUST WASHER, Pivot shaft
100193A, 100293R, 115083D, 115983E, 125183C, 125283R, 55872A, 55972A, 60072B, 60172C, 65272S, 65372R, 70442M, 70572B, 70773S, 70873C, 70973R, 75542B, 75642D, 85093B, 85193A, 85293R, 85993E, E60ELCDS, E60ELCUC, E70ELCIH, E70ELCNB, E70ELCOS, E70ELCRD,
0313447
0313447 THRUST WASHER, Forward & reverse gear
50172S, 50202C, 50302R, 50442M, 50902C, 55872A, 55972A, 60072B, 60172C, 65272S, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 70973R, 75542B, 75642D, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE
0313344
0383843
0383521
0383521 THRUST ROD AND RETAINER
100193A, 100293R, 115083D, 115983E, 125183C, 125283R, 85093B, 85193A, 85293R, 85993E
0314731
0314731 THRUST WASHER FORWARD AND REVERSE GEAR
100193A, 100293R, 100990S, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 85093B, 85193A, 85293R, 85393M, 85493B, 85593E, 85693
0316484
0316484 THRUST WASHER
100193A, 100293R, 115393M, 115493B, 115593, 115693D, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 50172S, 50202C, 50302R, 50442M, 50902C, 60172C, 65272S, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 70973R, 75542B, 75642D, 85193A, 85293R,