0317790 EVINRUDE THURST WASHER


0317790 THURST WASHER EVINRUDE 115393M, 115493B, 115593, 115693D, 115793S, 135383M, 135443B, 135543E, 135643D, 85393M, 85493B, 85593E, 85693D THURST
0317790 THURST WASHER EVINRUDE
Rating:
23

Buy THURST WASHER 0317790 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 107
 

BRP EVINRUDE entire parts catalog list:

115393M 1973
115493B 1974
115593 1975
115693D, 115693G, 115699D, 115699G 1976
115793S, 115799S, 85793S, 85799S 1977
135383M 1973
135443B, 135483B, 135489B 1974
135543E, 135583E, 135589E 1975
135643D, 135643G, 135683D, 135683G 1976
85393M 1973
85493B 1974
85593E 1975
85693D, 85693G, 85699G 1976

Information:


Table 1
Code    Position in degrees Before Top Center for Static Timing    Piston Displacement    
"AJ"     16    
2.54 mm (0.100 inch)    
"BJ"     16    
2.54 mm (0.100 inch)    
"FJ"     16    
2.51 mm (0.099 inch)    
"GJ"     22    
4.71 mm (0.185 inch)    
"HJ"     22    
4.71 mm (0.185 inch)    
"JJ"     22    
4.71 mm (0.185 inch)    
"KJ"     18    
3.17 mm (0.125 inch)    Type ... In-line cassetteDirection of rotation of the camshaft for the fuel injection pump ... Clockwise from the drive end
Illustration 1 g00385512
Fuel injection pump (1) Tighten the four union nuts that connect the high pressure fuel lines to the fuel injection pump to the following torque. ... 27 N m (20 lb ft) (2) Tighten the union nut that connects the fuel return line to the top of the fuel pump to the following torque. ... 20 N m (15 lb ft) (3) Tighten the four delivery valve holders to the following torque. ... 43 N m (32 lb ft) (4) Tighten the four mounting bolts and the two mounting nuts to the following torque. ... 22 N m (16 lb ft) (5) Tighten the bolt that connects the fuel supply line to the fuel pump to the following torque. ... 20 N m (15 lb ft)
Illustration 2 g00607092
(6) ShimThe shim adjusts the timing of the fuel injection pump. A thicker shim retards the timing. A thinner shim advances the timing. The timing changes one degree for each 0.10 mm (0.004 inch) difference in the thickness of the shim. More than one shim can be used. If the fuel injection pump is reinstalled, a new shim, which is the same thickness as the original shim, must be installed.Note: Do not use sealant on a shim. A thin layer of sealant is included with the final thickness of a new shim. Extra sealant will affect the timing of the fuel injection pump. If a shim is not required, a thin layer of 4C-9612 Silicone Sealant should be applied to the mating face of the cylinder block.If any of the following new components are installed, a new shim which has a thickness of 0.5 mm (0.020 inch) must be used in order to correctly adjust the timing of fuel injection.
Camshaft of the fuel injection pump
Cylinder blockThe following thicknesses of shims are available:
0.10 mm (0.004 inch)
0.20 mm (0.008 inch)
0.30 mm (0.012 inch)
0.40 mm (0.016 inch)
0.50 mm (0.020 inch) (7) Pin for the springs of the linkage of the fuel injection pump (8) The notch is in the shim for the pin. (7) The pin is on the in-line cassette. (9) Two dowels for aligning the shim and the fuel injection pumpCamshaft for Fuel Injection Pump
Illustration 3 g00386925
Components of the camshaft for the fuel injection pump (1) Camshaft gear (2) Cover (3) Key (4) Camshaft lobe (5) Tighten the bolts for the cover to the following torque. ... 9 N m (80 lb in)End play of camshaft for the fuel injection pump ... 0.005 to 0.140 mm (0.0002 to 0.0055 inch)Maximum permissible end play ... 0.35 mm (0.014 inch)


Back to top