0172910 TILT AID KIT EVINRUDE
E50BECNR, E60ECNM
TILT
Price: query
Rating:
BRP EVINRUDE entire parts catalog list:
Information:
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     2P-5518     Bearing Tool     1    
B     8T-5096     Dial Indicator Group     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Apply clean engine oil to the crankshaft main bearings prior to assembly. Do not apply oil to the back of the crankshaft main bearing. Ensure that the tabs on the back side of the crankshaft main bearings fit in the grooves of the crankshaft main bearing caps and the cylinder block.
Ensure that the crankshaft main bearings are installed in the correct locations. Two different part numbers are used in quantities of three and four. The part number having the quantity of four is to be installed on crankshaft main bearings 2, 3, 5, and 6. The part number having the quantity of three is to be installed on crankshaft bearing 1, 4, and 7. The thrust plate is to be installed on the center crankshaft main bearing only.
Illustration 1 g01147837
Note: The crankshaft end play is controlled by thrust plate (3) . Thrust plate (3) is located at the center of the crankshaft.
Install thrust plate (3) .
Use Tooling (A) to install the new upper halves of crankshaft main bearings (2) in the cylinder block. This half of the bearing has an oil hole.
Illustration 2 g01011713
Install the new lower halves of crankshaft main bearings (2) in crankshaft main bearing caps (1) . Do not apply oil to the back of the crankshaft main bearing.Note: Crankshaft main bearing caps (1) should be installed with the part number toward the right side of the engine. The numerical sequence is identified by stamped numbers 1 through 7 that are located on the bottom surface. The thrust plate is used on the number 4 crankshaft main bearing only.Note: Inspect the bolts for main bearing caps (1) . Refer to Reuse and Salvage Guidelines, SEBF8301, "Inspection and Reuse of Critical Fasteners Used in All Engines" to determine if the bolts should be replaced or reused.
Position crankshaft main bearing caps (1) with the part numbers toward the right-hand side of the cylinder block. Position crankshaft main bearing caps (1) in a numerical sequence.Note: If necessary, use new bolts for the installation of bearing caps (1) .
Apply clean "SAE 30W" oil or molybdenum grease to the bolt threads and the washers. Install the bolts. Refer to Table 2 for torque specifications.
Table 2
Torque Table    
Block Part Number     Tightening Torque    
239-7360     50 5 N m (37 4 lb ft). Rotate the bolts an additional 90 5 degrees.    
252-2180    
50 5 N m (37 4 lb ft). Rotate the bolts an additional 90 5 degrees.    
303-1384    
150 5 N m (110 4 lb ft). Rotate the bolts an additional 60 5 degrees    
Check the end play of the crankshaft with Tooling (B) . The end play must be 0.10 to 0.50 mm (0.004 to 0.020 inch).End By: Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Parts tilt EVINRUDE:
0172840
0172840 TILT CYLINDER ASSY.
115693D, 115793S, 135443B, 135543E, 135643D, 85693D, E35AELCDE, E35AELCUD, E40AELCCS, E40ECDE, E40ECUD, E45RCE, E50BECCS, E50BECDE, E50BECIC, E50BECNR, E50BECOB, E50BECRM, E50BECTA, E50BECUD, E55RCIM, E55RWLE, E60ECIA, E60ECNM, E60ECTB, E60ELCOD, E60
0122527
0122527 TILT BAND
115693D, 115793S, 135443B, 135543E, 135643D, 85693D, E35AELCDE, E35AELCUD, E40AELCCS, E40ECDE, E40ECUD, E45RCE, E50BECCS, E50BECDE, E50BECIC, E50BECNR, E50BECOB, E50BECRM, E50BECTA, E50BECUD, E55RCIM, E55RWLE, E60ECIA, E60ECNM, E60ECTB, E60ELCOD, E60
0172838
0172838 TILT LINE ASSY.,Upper
115693D, 115793S, 135543E, 135643D, 85693D, E35AELCDE, E35AELCUD, E40AELCCS, E40ECDE, E40ECUD, E45RCE, E50BECCS, E50BECDE, E50BECIC, E50BECNR, E50BECOB, E50BECRM, E50BECTA, E50BECUD, E55RCIM, E55RWLE, E60ECIA, E60ECNM, E60ECTB, E60ELCOD, E60ELCRE
0172872
0172872 TILT LINE ASSY.,Lower
115693D, 115793S, 135643D, 85693D, E35AELCDE, E35AELCUD, E40AELCCS, E40ECDE, E40ECUD, E45RCE, E50BECCS, E50BECDE, E50BECIC, E50BECNR, E50BECOB, E50BECRM, E50BECTA, E50BECUD, E55RCIM, E55RWLE, E60ECIA, E60ECNM, E60ECTB, E60ELCOD, E60ELCRE
0172822
0172822 TILT CYLINDER ASSY.,Complete
115693D, 115793S, 135643D, 85693D, E35AELCDE, E35AELCUD, E40AELCCS, E40ECDE, E40ECUD, E45RCE, E50BECCS, E50BECDE, E50BECIC, E50BECNR, E50BECOB, E50BECRM, E50BECTA, E50BECUD, E55RCIM, E55RWLE, E60ECIA, E60ECNM, E60ECTB, E60ELCOD, E60ELCRE
0208181
0208181 TILT HANDLE
50902C, 55874S, BE40EECR, BE40EEDS, BE40EEUC, BE50BEEDS, BE50ESECC, BE50RLEUC, E35AELCDE, E35AELCUD, E40AELCCS, E40ECDE, E40ECEC, E40ECOB, E40ECRM, E40ECUD, E40EEIA, E40EENJ, E40EEOD, E40EERE, E40EESR, E40EETB, E45RCE, E45RCEIA, E45RCENM, E45RCESR, E
0323226
0323226 TILT HANELD
E40ECOB, E40ECRM, E50BECIC, E50BECNR, E50BECOB, E50BECRM, E50BECTA, E55RCIM, E60ECIA, E60ECNM, E60ECTB, E60ELCOD, E60ELCRE