5040331 TILT STOPPER SHAFT (UPPER) EVINRUDE
B10EL4AAA, B10EL4AAB, B10EL4INS, E10EL4INS, E10TEL4AAB
TILT
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- STERN & SWIVEL BRACKET (EL MODELS) » 5040331
B10EL4INS 2012
E10EL4INS 2012
E10TEL4AAB 2012
Information:
2. Remove bolts (1), (2) and (4) to remove adapter (3) from the engine. 3. Remove elbow (5) and tube (6) from the oil pump.4. Remove the flange and tube (7) from the oil cooler bonnet. 5. Use tool (A) to fasten a hoist to oil pump (8).6. Remove bolts (9) and (10). Remove oil pump (8). The weight of the oil pump is 39 Kg (85 lb.). The following steps are for the installation of the oil pump.7. Put clean engine oil on the O-ring seals. Use tool (A) and a hoist to position oil pump (8). Make sure the splines on the pump shaft are correctly engaged with the splines of the oil pump drive. Install bolts (9) and (10) that hold the pump in position.8. Put clean engine oil on the O-ring seals and install tube (6) in the by-pass elbow. Put elbow (5) in position on tube (6) and the oil pump. Install the bolts to hold it in place.9. Put clean engine oil on the O-ring seals and install tube (7) and the flange as a unit in the oil cooler bonnet.10. Put the gaskets and adapter (3) in position. Install bolts (1), (2) and (4) to hold them in position.11. Fill the cooling system with coolant to the correct level. See the Maintenance Guide.Disassemble Oil Pump
Start By:a. remove oil pump
Cover (2) has spring tension under it. To prevent personal injury, loosen bolts (1) slowly, and the same amount, to remove the tension under the cover.
1. Remove bolts (1), cover (2), gasket (3), spring (4) and valve spool (5) from the pump body. 2. Remove cover assembly (6) and the gasket from the pump body. 3. Remove cover assembly (7) from the pump body. 4. Use tooling (A) to remove bearings (8) from cover assembly (7). 5. Remove shaft assemblies (10) from body assembly (9). 6. Use a press to remove gears (11) from the shaft assemblies. 7. Use tooling (A) to remove bearings (12) from body assembly (9).Assemble Oil Pump
1. Make an alignment of bearings (12) so that the joints are 45 15° from a line through the center of the bearing bores as shown.2. Use tooling (A) to install bearings (12) in the body assembly until they are 1.5 0.5 mm (.06 .02 in.) below the gear bore in the body assembly. Check the inside diameter of the bearings after installation. The diameter must be 31.811 0.013 mm (1.2524 .0005 in.). 3. Heat gears (11) to a maximum temperature of 316° C (600° F).4. Install gears (11) on two idler shaft assemblies (10) until they are 64.0 0.5 mm (2.52 .02 in.) from the body end of the shaft assemblies to the face of the gears.5. Install gear (11) on drive shaft assembly (13) until it is 47.0 0.5 mm (1.85 .02 in.) from the cover end of the shaft assembly to the face of the gear. 6. Install shaft assemblies (10) and (13) in body assembly (9). 7. Make sure dowels (14) and (15) are installed in cover assembly (7) so they extend 6.0 0.5 mm (.24 .02 in.) above the surface of the cover assembly.8. Use tooling (A) to install bearings (8) in cover assembly (7) with the joints of the bearings in the positions shown. 9. Put cover assembly (7) in position, and tighten the bolts to hold it to the body assembly. 10. Make sure the two pins in cover assembly (6) are installed so they extend 6.0 1.0 mm (.24 .04 in.) above the surface of the cover assembly. Install the gasket and cover assembly (6) on the body assembly. 11. Put clean engine oil on valve spool (5). Install valve spool (5), spring (4), gasket (3), cover (2) and the bolts in the body assembly.End By:a. install oil pump
Start By:a. remove oil pump
Cover (2) has spring tension under it. To prevent personal injury, loosen bolts (1) slowly, and the same amount, to remove the tension under the cover.
1. Remove bolts (1), cover (2), gasket (3), spring (4) and valve spool (5) from the pump body. 2. Remove cover assembly (6) and the gasket from the pump body. 3. Remove cover assembly (7) from the pump body. 4. Use tooling (A) to remove bearings (8) from cover assembly (7). 5. Remove shaft assemblies (10) from body assembly (9). 6. Use a press to remove gears (11) from the shaft assemblies. 7. Use tooling (A) to remove bearings (12) from body assembly (9).Assemble Oil Pump
1. Make an alignment of bearings (12) so that the joints are 45 15° from a line through the center of the bearing bores as shown.2. Use tooling (A) to install bearings (12) in the body assembly until they are 1.5 0.5 mm (.06 .02 in.) below the gear bore in the body assembly. Check the inside diameter of the bearings after installation. The diameter must be 31.811 0.013 mm (1.2524 .0005 in.). 3. Heat gears (11) to a maximum temperature of 316° C (600° F).4. Install gears (11) on two idler shaft assemblies (10) until they are 64.0 0.5 mm (2.52 .02 in.) from the body end of the shaft assemblies to the face of the gears.5. Install gear (11) on drive shaft assembly (13) until it is 47.0 0.5 mm (1.85 .02 in.) from the cover end of the shaft assembly to the face of the gear. 6. Install shaft assemblies (10) and (13) in body assembly (9). 7. Make sure dowels (14) and (15) are installed in cover assembly (7) so they extend 6.0 0.5 mm (.24 .02 in.) above the surface of the cover assembly.8. Use tooling (A) to install bearings (8) in cover assembly (7) with the joints of the bearings in the positions shown. 9. Put cover assembly (7) in position, and tighten the bolts to hold it to the body assembly. 10. Make sure the two pins in cover assembly (6) are installed so they extend 6.0 1.0 mm (.24 .04 in.) above the surface of the cover assembly. Install the gasket and cover assembly (6) on the body assembly. 11. Put clean engine oil on valve spool (5). Install valve spool (5), spring (4), gasket (3), cover (2) and the bolts in the body assembly.End By:a. install oil pump
Parts tilt EVINRUDE:
5040496
5040496 *Tilt Stopper Grip
B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B4R4AAA, B4R4INS, B6R4AAA, B6R4INS, E10TEL4AAB
5040290
5040290 TILT SWITCH COVER
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
5040291
5040291 TILT SWITCH PLUG
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
5040323
5040330
5040332
5040328
5041335
5041335 TILT STOPPER ASSEMBLY
B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, E10TEL4AAB