0115207 TRANSMISSION SHAFT EVINRUDE
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSIR, E2WRSSC, E3ROECS, E3ROEOB, E3ROSIA, E3ROSSR, E3WREES, E3WRSIR, E3WRSSC, HE2DRETC, HE3REIC, HE3RENR, HE3RETC
TRANSMISSION
Price: query
Rating:
Number on catalog scheme: 31
Compatible models:
BRP EVINRUDE entire parts catalog list:
- GEARCASE » 0115207
BE3ROEDE, E3ROEDE, HE3ROEDE, HE3RSA, SE3ROEDE 1996
BE3ROEUD, E3ROEUD, HE3ROEUD, HE3RSK, SE3ROEUD 1997
E2RECS, E2RSS 1998
E2ROEOB 1995
E2WREES 1999
E2WRSIR 2001
E2WRSSC 2000
E3ROECS, E3ROLECS, E3RSS 1998
E3ROEOB 1995
E3ROSIA 2001
E3ROSSR 2000
E3WREES 1999
E3WRSIR 2001
E3WRSSC 2000
HE2DRERM, HE2DRETC 1993,1994
HE3REIC 1991
HE3RENR 1992
HE3RERM, HE3RETC 1993,1994
Information:
3. Remove bolts (1) and main bearing caps (2). Remove the lower halves of the main bearings from the caps. 4. Install two of the bolts that hold the flywheel in place in the end of the crankshaft.5. Fasten a hoist and remove crankshaft (3) from the engine. The weight of the crankshaft is 120 lb. (54 kg). 6. Remove the upper halves of the main bearings from the cylinder block.7. Install tooling (B) and remove the gear from the crankshaft.Install Crankshaft And Gear
1. Install the key for the crankshaft gear on the crankshaft.2. Heat the gear for the crankshaft in oil to a maximum temperature of 300°F (148°C). Install the gear on the crankshaft with the timing mark on the crankshaft gear toward the crankshaft pulley end of the crankshaft.3. Thoroughly clean the area where the upper halves of the main bearings fit. Install the upper halves of the main bearings in the cylinder block. The main bearing half with a hole in it is the upper bearing.4. Install the thrust bearing for the No. 4 main.5. Put clean engine oil on the bearings and journals of the crankshaft.6. Install two of the bolts that hold the flywheel in place in the end of the crankshaft. Fasten a hoist and put the crankshaft in position in the block. Make sure the timing mark on the crankshaft gear is in alignment with the timing mark on the camshaft gear.7. Clean the main bearing caps and install the lower halves of the main bearings in the caps.
When installing bearing caps, make sure the number on the side of the cap is next to and respective with the number on the engine block.
8. Check the bearing clearance with wire (B). Put the caps in position and install the bolts. Tighten the bolts in number order as follows: a) Tighten bolts 1 through 10 to a torque of 30 3 lb.ft. (4.1 0.4 mkg). b) Put a mark on each bolt head and bearing cap. Tighten bolts 1 through 10 120 5° more.9. Remove the bearing caps and measure the thickness of the wire. The main bearing clearance must be .0015 to .0045 in. (0.038 to 0.114 mm). The maximum permissible clearance is .006 in. (0.15 mm).10. Put clean engine oil on the bolt threads, washer faces, and lower halves of the main bearings. Put the bearing caps in position and install the bolts. Tighten the bolts in number order as follows: a) Tighten bolts 1 through 10 to a torque of 30 3 lb.ft. (4.1 0.4 mkg). b) Put a mark on each bolt head and bearing cap. Tighten bolts 1 through 10 120 5° more.11. Install indicator group (A) and check the end play of the crankshaft. The end play is controlled by the thrust bearing on No. 4 main bearing. The end play with new bearings must be .006 .003 in. (0.15 0.08 mm). The maximum permissible end play with used bearings is .012 in. (0.30 mm).end by: a) install timing gear cover and oil pumpb) install pistonsc) install valve liftersd) install flywheel housinge) install engine and radiator
1. Install the key for the crankshaft gear on the crankshaft.2. Heat the gear for the crankshaft in oil to a maximum temperature of 300°F (148°C). Install the gear on the crankshaft with the timing mark on the crankshaft gear toward the crankshaft pulley end of the crankshaft.3. Thoroughly clean the area where the upper halves of the main bearings fit. Install the upper halves of the main bearings in the cylinder block. The main bearing half with a hole in it is the upper bearing.4. Install the thrust bearing for the No. 4 main.5. Put clean engine oil on the bearings and journals of the crankshaft.6. Install two of the bolts that hold the flywheel in place in the end of the crankshaft. Fasten a hoist and put the crankshaft in position in the block. Make sure the timing mark on the crankshaft gear is in alignment with the timing mark on the camshaft gear.7. Clean the main bearing caps and install the lower halves of the main bearings in the caps.
When installing bearing caps, make sure the number on the side of the cap is next to and respective with the number on the engine block.
8. Check the bearing clearance with wire (B). Put the caps in position and install the bolts. Tighten the bolts in number order as follows: a) Tighten bolts 1 through 10 to a torque of 30 3 lb.ft. (4.1 0.4 mkg). b) Put a mark on each bolt head and bearing cap. Tighten bolts 1 through 10 120 5° more.9. Remove the bearing caps and measure the thickness of the wire. The main bearing clearance must be .0015 to .0045 in. (0.038 to 0.114 mm). The maximum permissible clearance is .006 in. (0.15 mm).10. Put clean engine oil on the bolt threads, washer faces, and lower halves of the main bearings. Put the bearing caps in position and install the bolts. Tighten the bolts in number order as follows: a) Tighten bolts 1 through 10 to a torque of 30 3 lb.ft. (4.1 0.4 mkg). b) Put a mark on each bolt head and bearing cap. Tighten bolts 1 through 10 120 5° more.11. Install indicator group (A) and check the end play of the crankshaft. The end play is controlled by the thrust bearing on No. 4 main bearing. The end play with new bearings must be .006 .003 in. (0.15 0.08 mm). The maximum permissible end play with used bearings is .012 in. (0.30 mm).end by: a) install timing gear cover and oil pumpb) install pistonsc) install valve liftersd) install flywheel housinge) install engine and radiator
Parts transmission EVINRUDE:
0115445