5008161 **TRIM TAB Assy EVINRUDE
E15DHPLAAA, E15DHPLAAB, E15DHPLIIC, E15DHPLINR, E15DHTLAAA, E15DHTLAAB, E15DHTLIIC, E15DHTLINR, E25DELAAA, E25DELIIH, E25DELINA, E25DELSES, E25DPLAAA, E25DPLAAB, E25DPLIIG, E25DPLIIH, E25DPLINA, E25DPLSES, E25DRAAA, E25DRIIH, E25DRINA, E25DRLSES, E25
TRIM
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Compatible models:
E15DHPLAAA
E15DHPLAAB
E15DHPLIIC
E15DHPLINR
E15DHTLAAA
E15DHTLAAB
E15DHTLIIC
E15DHTLINR
E25DELAAA
E25DELIIH
E25DELINA
E25DELSES
E25DPLAAA
E25DPLAAB
E25DPLIIG
E25DPLIIH
E25DPLINA
E25DPLSES
E25DRAAA
E25DRIIH
E25DRINA
E25DRLSES
E25DTEAAA
E25DTEIIG
E25DTEIIH
E25DTEINA
E25DTELSES
E25DTLAAA
E25DTLAAB
E25DTLIIH
E25DTLINA
E25DTLSES
E30DELAAA
E30DELIIH
E30DELINA
E30DELSES
E30DPLAAA
E30DPLAAB
E30DPLIIH
E30DPLINA
E30DPLSES
E30DRAAA
E30DRIIG
E30DRIIH
E30DRINA
E30DRLSES
E30DTELAAA
E30DTELIIH
E30DTELINA
E30DTELSES
E30DTLAAA
E30DTLAAB
E30DTLIIH
E30DTLINA
E30DTLSES
EVINRUDE
BRP EVINRUDE entire parts catalog list:
- GEARCASE, H-Type » 5008161
E15DHPLIIC, E15DHPLIIH, E15HPSLIIH, E15HPSLIIS 2011
E15DHPLINR, E15HPSLINC, E15HPSXINC 2012
E15DHTLAAA, E15HTSLAAA, E15HTSXAAA 2012
E15DHTLAAB, E15HTSLAAB, E15HTSXAAB 2012
E15DHTLIIC, E15DHTLIIH, E15HTSLIIH, E15HTSLIIS 2011
E15DHTLINR, E15HTSLINC, E15HTSXINC 2012
E25DELAAA, E25DELAAB 2012
E25DELIIH, E25DELIIR 2011
E25DELINA 2012
E25DELSES 2009
E25DPLAAA, E25DPSLAAA 2012
E25DPLAAB, E25DPSLAAB 2012
E25DPLIIG 2011
E25DPLIIH, E25DPLIIR, E25DPSLIIH, E25DPSLIIS 2011
E25DPLINA, E25DPSLINC 2012
E25DPLSES 2009
E25DRAAA, E25DRAAB, E25DRLAAA, E25DRLAAB, E25DRSAAA, E25DRSAAB, E25DRSLAAA, E25DRSLAAB 2012
E25DRIIH, E25DRIIR, E25DRLIIH, E25DRLIIR, E25DRSIIH, E25DRSIIS, E25DRSLIIH, E25DRSLIIS 2011
E25DRINA, E25DRLINA, E25DRSINC, E25DRSLINC 2012
E25DRLSES, E25DRSES 2009
E25DTEAAA, E25DTEAAB, E25DTELAAA, E25DTELAAB, E25TESLAAA, E25TESLAAB 2012
E25DTEIIG 2011
E25DTEIIH, E25DTEIIR, E25DTELIIH, E25DTELIIR, E25TESLIIH, E25TESLIIS 2011
E25DTEINA, E25DTELINA, E25TESLINC 2012
E25DTELSES, E25DTESES 2009
E25DTLAAA, E25DTSLAAA 2012
E25DTLAAB, E25DTSLAAB 2012
E25DTLIIH, E25DTLIIR, E25DTSLIIH, E25DTSLIIS 2011
E25DTLINA, E25DTSLINC 2012
E25DTLSES 2009
E30DELAAA, E30DELAAB 2012
E30DELIIH, E30DELIIR 2011
E30DELINA 2012
E30DELSES 2009
E30DPLAAA, E30DPSLAAA 2012
E30DPLAAB, E30DPSLAAB 2012
E30DPLIIH, E30DPLIIR, E30DPSLIIH, E30DPSLIIS 2011
E30DPLINA, E30DPSLINC 2012
E30DPLSES 2009
E30DRAAA, E30DRAAB, E30DRLAAA, E30DRLAAB, E30DRSAAA, E30DRSAAB, E30DRSLAAA, E30DRSLAAB 2012
E30DRIIG, E30DRLIIG 2011
E30DRIIH, E30DRIIR, E30DRLIIH, E30DRLIIR, E30DRSIIH, E30DRSIIS, E30DRSLIIH, E30DRSLIIS 2011
E30DRINA, E30DRLINA, E30DRSINC, E30DRSLINC 2012
E30DRLSES, E30DRSES 2009
E30DTELAAA, E30DTELAAB, E30TESLAAA, E30TESLAAB 2012
E30DTELIIH, E30DTELIIR, E30TESLIIH, E30TESLIIS 2011
E30DTELINA, E30TESLINC 2012
E30DTELSES 2009
E30DTLAAA, E30DTSLAAA 2012
E30DTLAAB, E30DTSLAAB 2012
E30DTLIIH, E30DTLIIR, E30DTSLIIH, E30DTSLIIS 2011
E30DTLINA, E30DTSLINC 2012
E30DTLSES 2009
Information:
Illustration 1 g02265653
Schematic for the 834G Wheel Tractor (BPC), 836G Landfill Compactor (BRL), and 988G Wheel Loader (BNH)Schematic for the 814F Wheel Dozer (BGF), 815F Soil Compactor (BKL), and 816F Landfill Compactor (BMR)
Illustration 2 g02271513
Schematic for the 814F Wheel Dozer (BGF), 815F Soil Compactor (BKL), and 816F Landfill Compactor (BMR)Schematic for the 824G II Wheel Tractor (AWW), 950G II Wheel Loader (AYB), and 826G II Landfill Compactor (AYH)
Illustration 3 g02265676
Schematic for the 824G II Wheel Tractor (AWW), 950G II Wheel Loader (AYB), and 826G II Landfill Compactor (AYH)Test Step 1. Inspect Electrical Connectors and Wiring
Remove the electrical power from the ECM.
Thoroughly inspect the J1/P1 ECM connector. Thoroughly inspect the connector for the engine shutdown switch. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Check the ECM connector (allen head screw) for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and the wiring for abrasion and for pinch points.Expected Result:All of the connectors, pins, and sockets are coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and connectors appear to be OK. Proceed to Test Step 2.
Not OK - The connectors and/or wiring are not OK.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Switch Status on Cat ET
Connect Cat ET to the service tool connector.
Restore the electrical power to the ECM.
Observe the status for "Shutdown Switch" on Cat ET while you operate the engine shutdown switch.
Remove the electrical power from the ECM.Expected Result:The status is "On" with the switch in the STOP position. The status is "Off" with the switch in the RUN position.Results:
OK - The switch is operating normally.Repair: Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" if an intermittent electrical problem is suspected.STOP
Not OK - The status of the shutdown switch is incorrect. Proceed to Test Step 3.Test Step 3. Short the Wires at the Switch
Disconnect the connector for the engine shutdown switch.
At the switch connector, install a jumper wire between the pin for Engine Shutdown Switch (NC)and the pin for Digital Sensor Return.
Restore the electrical power to the ECM and observe the status for "Shutdown Switch" on Cat ET.The status should be "Off".
Remove the electrical power from the ECM.
Remove the jumper wire.
At the switch connector, install the jumper wire between the pin for Engine Shutdown Switch (NO)and the pin for Digital Sensor Return.
Restore the electrical power to the ECM and observe the status for "Shutdown Switch" on Cat ET.The status should be "On".
Remove the electrical power from the ECM.
Remove the jumper wire.Expected Result:The status is "Off" with the jumper wire between the pin for Engine Shutdown Switch (NC) and the pin for Digital Sensor Return. The status changes to "On" with the jumper wire between the pins for Engine Shutdown Switch (NO) Digital Sensor Return.Results:
OK - The wiring from the connector to the ECM is OK. There is a problem with the switch.Repair: Temporarily connect a new switch. Verify that the new switch solves the problem before you permanently install the new switch.STOP
Not OK - The ECM did not detect the shorts. There is a problem in the harness and/or the ECM. Proceed to Test Step 4.Test Step 4. Short the Switch Inputs at the ECM
Remove the electrical power from the ECM.
Install a 208-0059 Adapter Cable As (70-PIN BREAKOUT) at the J1/P1 ECM connector.
Install a jumper wire between the pin for Engine Shutdown Switch (NC) and the pin for Digital Sensor Return at the breakout.
Restore the electrical power to the ECM and observe the status for "Shutdown Switch" on Cat ET.The status should be "Off".
Remove the electrical power from the ECM.
Remove the jumper wire from the breakout.
Install the jumper wire between the pin for Engine Shutdown Switch (NO) and the pin for Digital Sensor Return at the breakout.
Restore the electrical power to the ECM and observe the status for "Shutdown Switch" on Cat ET.The status should be "On".
Remove the electrical power from the ECM.Expected Result:The status is "Off" with the jumper wire between the pin for Engine Shutdown Switch (NC) and the pin for Digital Sensor Return. The status changes to "On" with the jumper wire between the pins for Engine Shutdown Switch (NO) and Digital Sensor Return.Results:
OK - The ECM properly reads the inputs for the shutdown switch at the ECM connector P1 but not at the connector for the switch.Repair: The wiring harness is faulty. Repair the wiring harness. Verify that the repair eliminates the problem.STOP
Not OK - The ECM is not reading the inputs for the shutdown switch properly.Repair: Verify your results.Replace the ECM. Refer to electronic troubleshooting Troubleshooting, "Replacing the ECM" before replacing the ECM.STOP
Parts trim EVINRUDE:
0355125
0355125 ***TRIM TAB
E15DHPLAAA, E15DHPLAAB, E15DHPLIIC, E15DHPLINR, E15DHTLAAA, E15DHTLAAB, E15DHTLIIC, E15DHTLINR, E25DELAAA, E25DELIIH, E25DELINA, E25DELSES, E25DPLAAA, E25DPLAAB, E25DPLIIG, E25DPLIIH, E25DPLINA, E25DPLSES, E25DRAAA, E25DRIIH, E25DRINA, E25DRLSES, E25
0353888
0353888 *TRIM TAB
E15DHPLISS, E15DHTLISS, E25DELISC, E25DELSES, E25DPLISC, E25DPLSES, E25DRISC, E25DRLSES, E25DTEISC, E25DTELSES, E25DTLISC, E25DTLSES, E30DELISC, E30DELSES, E30DPLISC, E30DPLSES, E30DRISC, E30DRLSES, E30DTELISC, E30DTELSES, E30DTLISC, E30DTLSES