0352513 EVINRUDE VALVE, Exhaust - Stbd

Introduction
ReferenceOperation and Maintenance, SEBU7731, "216B, 226B, 232B, 236B, 242B, 246B, 248B, 252B, 262B, and 268B Skid Steer Loaders"ReferenceOperation and Maintenance, SEBU8385, "216B2, 226B2, 232B2, 236B2, 242B2, and 252B2 Skid Steer Loaders"ReferenceOperation and Maintenance, SEBU7732, "247B, 257B, 267B, 277B, and 287B Multi Terrain Loaders"ReferenceOperation and Maintenance, SEBU7732, "247B2 and 257B2 Multi Terrain Loaders"ReferenceOperation and Maintenance, SEBU8495, "216B3, 226B3, 236B3, 242B3, and 252B3 Skid Steers Loaders, 247B3 and 257B3 Multi Terrain Loaders and 259B3 Compact Track Loader"This Special Instruction provides the information that is needed for installing the 290-9911 Engine Enclosure Seal Kit on the machines that are identified above. The kit contains various seals, covers, and brushes. These components are designed to cover the openings that exist between the frame and the body of the machines. These components prevent wood chips and other materials from entering the engine compartment and the lower frame.Caterpillar recommends the use of a vented rear door. Refer to the instructions in Special Instructions, REHS4062, "Modifying the Rear Door for Improved Ventilation of the Engine Compartment" and the 265-4419 Debris Guard Kit (TURBOCHARGER) (EXHAUST MANIFOLD) with the 290-9911 Engine Enclosure Seal Kit .The vented rear door that is provided in this kit is fabricated. The rear door is fabricated from a vinyl coated polyester material and the rear door utilizes hook and loop fasteners. "Two-sided tape" attaches the hook and loop fasteners to the machine. After the adhesive tape has cured, you can remove the cover assemblies and you can reinstall the cover assemblies, as needed.Note: Some of the components in this kit utilize adhesive strips and adhesive backing as the means for attaching the component. Mounting surfaces for these components must be clean and free of grease in order to ensure proper adhesion. Use a cleaning solvent or a standard degreaser in order to remove grease and oil from the surface. Then, wipe the mounting surface with alcohol and allow the surface to dry completely before applying the adhesive.Note: The cure time for the adhesive that is used on components in this kit is 24 hours. Once the adhesive is correctly placed on the mounting surface, the adhesive must not be disturbed for 24 hours.Do not perform any procedure that is outlined in this publication until you read the information. Make sure that you understand the information that is contained in this document.Parts Information
Illustration 1 g01419845
Pictorial view of the components in the 290-9911 Engine Enclosure Seal Kit
Table 1
Parts List    
Item    Quantity    Part Number    Description    
1     2     7K-1181     Cable Strap    
2     1     297-2585     Grill As    
3     1     297-2591     Grill As    
4     1     301-5162     Gasket    
5     2     301-5163     Plate    
6     1     301-5164     Gasket    
7     1     308-9725     Grill As    
8     1     309-8498     Cover As    
9     1     310-6266     Cover As    
10     1     310-6267     Cover As    
11     1     310-6268     Cover As    
12     2     310-9267     Cover As    
13     1     311-3934     Hood Bracket As    
14     4     3E-8020     Screw    
15     2     6V-7357     Bolt (M6X1)    
16     16     6V-7743     Locknut (M6X1)    
17     1     7X-2533     Bolt (M6X1)    
18     13     8T-4138     Bolt (M6X1)    
19     32     8T-4205     Hard Washer    
20     120 cm (47 inch)     6V-6604     Seal (1) (2)    
21    
82 cm (32 inch)     124-3243     Seal    
22    
179 cm (70 inch)     310-6270     Seal    
23    
82 cm (32 inch)     310-9334     Seal    
( 1 ) Part has been discontinued.
( 2 ) Order 6V-6604 Seal for service.
Table 2
Miscellaneous Part    
Item     Quantity     Part Number     Description    
24     1     4C-4030     Thread Lock Compo