5032643 EVINRUDE VALVE, Manual


5032643 VALVE, Manual EVINRUDE E70PL4SIA VALVE
5032643 VALVE, Manual EVINRUDE
Rating:
58

Buy VALVE, Manual 5032643 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$99.99

14-03-2025

US: FiveStarMarine
Five Star Marine Johnson Manual Release Valve 0435260 435260 5032643 05032643 5033941 05033941
Five Star Marine
$42.46
 

19-10-2020
4.40924524[1.80] Pounds
-: -
Connected Essentials CEM650 Patriot (2007-2011) Car Mat Set, Grey with Black Trim, Premium
Complete set of 4 tailored custom fit car mats - designed and manufactured specifically for Chrysler Patriot Jeep (2007-2011) || Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
Number on catalog scheme: 29
 

Compatible models:

E70PL4SIA   EVINRUDE

BRP EVINRUDE entire parts catalog list:

E70PL4SIA 2001

Information:


Table 1
Diagnostic Codes for the EFLP Relay
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
1075-5 3666-5 Engine Electric Lift Pump for Engine Fuel Supply : Current Below Normal The Electronic Control Module (ECM) detects the following conditions:
There are no active 168 diagnostic codes.
The ECM is not attempting to power the relay or there is an open circuit.
The ECM has been powered for at least 2 seconds.
There is a low current condition in the EFLP relay circuit or wiring for more than 2 seconds.
The warning light will come on. The diagnostic code will be logged.
The ECM is unable to activate the relay for the EFLP or power the pump. The EFLP will not operate or the EFLP will operate all the time. The engine will not operate.
1075-6 3666-6 Engine Electric Lift Pump for Engine Fuel Supply : Current Above Normal The ECM detects the following conditions:
There are no active 168 diagnostic codes.
The ECM is attempting to power the relay or the EFLP.
The ECM has been powered for at least 2 seconds.
There is a high current condition in the EFLP relay circuit or a short circuit in the wiring for more than 2 seconds.
The warning light will come on. The diagnostic code will be logged.
The ECM is unable to activate the relay for the EFLP or power the pump. The EFLP will not operate or the EFLP will operate all the time. The engine will not operate.
The ECM will continue to attempt to activate the relay or power the pump. If the current is OK for 6 seconds, then the diagnostic code will be cleared. The following background information is related to this procedure:The EFLP is used to provide positive fuel pressure to the high-pressure fuel pump. When the keyswitch is turned to the ON position, the ECM will activate the EFLP. If the engine is not running, the ECM will deactivate the EFLP after 2 minutes.
Illustration 1 g06154498
Schematic for the Electric Fuel Lift Pump (EFLP) with a relay
Illustration 2 g02138993
View of the pin location on the P1 connector for the EFLP
(21) EFLP relay supplyComplete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Turn the keyswitch to the OFF position.
B. Thoroughly inspect the connectors between the EFLP relay and the engine ECM. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the EFLP relay.
D. Check the screw for the ECM connector for the correct torque of 6 N m (53 lb in).
E. Check the harness and wiring for abrasion and for pinch points from the injectors to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify that the


Parts valve EVINRUDE:

5030669
 
5030669 VALVE, Intake
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030670
 
5030670 VALVE, Exhaust
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5031105
 
5031105 VALVE, Needle
E40PL4SSC, E50PL4SSC, E50PL4SSC, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030712
 
5030712 VALVE, Oil relief
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5032471
VALVE, Water pressure
5032471 VALVE, Water pressure
E40PL4SIR, E50PL4SIR, E50PL4SIR, E70, E70PL4SIA
Back to top