0115243 EVINRUDE WASHER, Tilt bolt


0115243 WASHER, Tilt bolt EVINRUDE BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSIR, E2WRSSC, E3ROECS, E3ROEOB, E3ROSIA, E3ROSSR, E3WREES, E3WRSIR, E3WRSSC, HE2DRETC, HE3REIC, HE3RENR, HE3RETC WASHER
0115243 WASHER, Tilt bolt EVINRUDE
Rating:
63

Buy WASHER, Tilt bolt 0115243 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 10
 

BRP EVINRUDE entire parts catalog list:

BE2REDE, E2ROEDE, HE2REDE, HE2RSA, SE2REDE 1996
BE2REUD, E2ROEUD, HE2REUD, HE2RSK 1997
BE3ROEDE, E3ROEDE, HE3ROEDE, HE3RSA, SE3ROEDE 1996
BE3ROEUD, E3ROEUD, HE3ROEUD, HE3RSK, SE3ROEUD 1997
E2RECS, E2RSS 1998
E2ROEOB 1995
E2WREES 1999
E2WRSIR 2001
E2WRSSC 2000
E3ROECS, E3ROLECS, E3RSS 1998
E3ROEOB 1995
E3ROSIA 2001
E3ROSSR 2000
E3WREES 1999
E3WRSIR 2001
E3WRSSC 2000
HE2DRERM, HE2DRETC 1993,1994
HE3REIC 1991
HE3RENR 1992
HE3RERM, HE3RETC 1993,1994

Information:

start by: a) remove governor from fuel injection pump housing1. Remove the fuel injection pumps as follows: a) Remove the protection cap and washer (1). b) Install wrench (A) and remove bushing (2) from housing.c) Remove the seal (3). d) Install extractor (B).e) Lift the fuel injection pump out of the housing.f) Remove the spacer (4). Keep the spacers (4) and pumps together, and put a mark on them as to their location in the fuel injection pump housing.2. Disassemble the fuel injection pump as follows: a) Remove the bonnet (5), ring (6), spring (7), and check valve (8) from the barrel (9).b) Remove the plunger (10), washer (11), and spring (12) from the barrel (9).
During disassembly and assembly of fuel injection pumps, do not cause damage to plunger surfaces. The barrel and plunger are exactly fitted, and the parts can not be changed with other barrels or plungers.
3. Remove the rack (13).4. Remove the lifters (14). Put identification on the lifters and keep them together with their respective pump and spacers. 5. Remove the camshaft plate (15), bolt and lock. 6. Remove the spring (16) and the gear (17) from the camshaft. 7. Remove the camshaft (19). 8. Install tool group (C) and remove the camshaft bearings from the housing of injection pumps.9. Remove the two bearings (18) from the fuel injection pump housing.Assemble Fuel Injection Pump Housing
1. Install the camshaft bearings in the housing of injection pumps using tool group (C). Install the bearing toward governor end of housing so the oil hole in bearing is in alignment with oil hole in housing. Install the two bearings on each end of the housing so the edge of bearing will be even with end of housing. 2. Install the two rack bearings in the housing of injection pumps with tooling (D). Install the bearing toward governor end of housing so it will be .195 .005 in. (4.95 0.13 mm) below end of housing. Install the rack bearing at the other end of housing so it will be even with face of pump housing. 3. Put clean SAE 30 engine oil on camshaft. Install the camshaft in fuel injection pump housing. 4. Put the governor drive gear (1) and spring (2) in position on the camshaft. Install the camshaft plate (3), bolt, and lock. 5. Install the lifters (4) in their respective positions in housing. Put clean fuel oil all over the rack. Install rack (5) in housing of injection pumps so the groove (slot) in rack is toward governor end of housing.6. Install the spacers in their respective positions in housing. When installing new lifters and pumps, it is necessary to make adjustment of the fuel pump timing. See FUEL INJECTION PUMP TIMING DIMENSION SETTING, OFF ENGINE in TESTING AND ADJUSTING.7. Assemble the fuel injection pumps as follows: a) Put clean fuel oil on all parts.b) Install the spring, washer, and plunger in the barrel.c) Install the spring, check valve, bonnet, and ring on the barrel.
Do not install fuel injection pumps until the rack has been put in the center position.
8. Put the rack in center position with tooling (E) as follows: a) Install location fixture (6) on the fuel injection pump housing.b) Install the gauge (7). Move the gauge (7) to zero. Push the rack (5) against the gauge. c) Install the clamp (8) on pump housing as illustrated. This will keep the rack in the center while installing the fuel injection pumps.9. With the rack in the center, install the fuel injection pumps as follows: a) Turn the camshaft until cam of camshaft is in DOWN position for installation of pump. b) Install the extractor (B) on pump.c) Look down the pump and put the notches (9) in bonnet and barrel in alignment with the groove (slot) (10) in pump gear segment. The groove (slot) (10) must be in alignment with the center of notches (9). Put the pump into position so that notches (9) are in alignment with the guide pins in bore of housing. Install the pump in its respective position in the pump housing. d) Install the seal and bushing (11). Push down on extractor (B), and tighten bushing by hand until the bushing is even with top of housing. If installation of the bushing cannot be made this far by hand, remove it. Remove pump, put components in alignment again and install the bushing again.
Do not force bushing even with face of pump housing using a wrench. If installation of pump is correct, bushing can be tightened by hand until it is even with face of pump housing.
e) After installation of each pump, check the rack travel as follows: Move the clamp (8) away from the end of rack. Check rack travel with gauge (7). If installation of the pump gear has been correct respective to rack, total rack must be about .800 in. (20.3 mm). If total rack travel cannot be made, remove the pump, put components in alignment, and install pump again. f) Remove extractor (B) and tooling (E). Install wrench (A) and tighten retaining bushing to 150 10 lb.ft. (20.7 . 1.4 mkg). Remove wrench (A). Install the felt washers and protection caps.end by: a) install governor on fuel injection pump housing


Parts washer EVINRUDE:

0303107
 
0303107 WASHER, Pinion to brkt
18002C, 18802A, 18902B, 25002C, 25902B, 33002M, 33802M, 33902A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 6002B, 6102E, 6202D, 6302S, 6402C, 6504R, 6604A, 6704M, 6802A, 6804B, 6902M, 6904E, BE2REDE, BE2REUD, BE3REDS, BE3ROEDE, BE3ROEUD, BE4BRED
0115583
 
0115583 WASHER, Choke plate
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSIR, E2WRSSC, E3ROECS, E3ROEOB, E3ROSIA, E3ROSSR, E3WREES, E3WRSIR, E3WRSSC, HE2DRETC, HE3REIC, HE3RENR, HE3RETC
0115590
 
0115590 WASHER, Throttle lever
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSIR, E2WRSSC, E3ROECS, E3ROEOB, E3ROSIA, E3ROSSR, E3WREES, E3WRSIR, E3WRSSC, HE2DRETC, HE3REIC, HE3RENR, HE3RETC
0114992
WASHER, Fill & drain
0114992 WASHER, Fill & drain
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSIR, E2WRSSC, E3ROECS, E3ROEOB, E3ROSIA, E3ROSSR, E3WREES, E3WRSIR, E3WRSSC, HE2DRETC, HE3REIC, HE3RENR, HE3RETC
0115284
 
0115284 WASHER, Water pump cover
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSIR, E2WRSSC, E3ROECS, E3ROEOB, E3ROSIA, E3ROSSR, E3WREES, E3WRSIR, E3WRSSC, HE2DRETC, HE3REIC, HE3RENR, HE3RETC
0115199
 
0115199 WASHER, Mtg. screw, gas bottle
BE10FAEDC, BE10FAEUR, BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, BE5FRBECC, BE5FRBEUS, BE8FRBECA, BE8FRBEDC, BE8FRBEUR, E10FOECA, E2RECS, E2ROEOB, E2WREES, E2WRSIR, E2WRSSC, E3ROECS, E3ROEOB, E3ROSSR, E3WREES, E3WRSIR, E3WRSSC, E5R4EEM, E5R4EEM, E5R4SIE,
0115251
 
0115251 WASHER, Friction adjustment
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSIR, E2WRSSC, E3ROECS, E3ROEOB, E3ROSIA, E3ROSSR, E3WREES, E3WRSIR, E3WRSSC, HE2DRETC, HE3REIC, HE3RENR, HE3RETC
Back to top