0306459 EVINRUDE WASHER,Tilt lock rod

Introduction
Table 1
Revision Summary of Changes in SEBF8170
29 Corrected specifications for C175 Scavenge pump (Diameter of gear shafts, Bore in bearings for the gear shafts after assembly, and Bore in oil pump body for bearings).
28 Added new serial number prefixes for New Product Introduction (NPI).
27 Added new serial number prefixes for New Product Introduction (NPI) and 12 part numbers.
25–26 Combined information from SEBF2127, SEBF2144, SEBF2156, SEBF2161, SEBF9044, SEBF9198, added 4 part numbers and repaired 26 pixelated illustrations.
24 Added verbiage for C175 oil pump shafts. © 2020 Caterpillar® All Rights Reserved. This guideline is for the use of Cat dealers only. Unauthorized use of this document or the proprietary processes therein without permission may be violation of intellectual property law.Information contained in this document is considered Caterpillar: Confidential Yellow.This Reuse and Salvage Guideline contains the necessary information to allow a dealer to establish a parts reusability program. Reuse and salvage information enables Caterpillar dealers and customers to benefit from cost reductions. Every effort has been made to provide the most current information that is known to Caterpillar. Continuing improvement and advancement of product design might have caused changes to your product which are not included in this publication. This Reuse and Salvage Guideline must be used with the latest technical information that is available from Caterpillar.For technical questions when using this document, work with your Dealer Technical Communicator (TC).To report suspected errors, inaccuracies, or suggestions regarding the document, submit a form for feedback in the Service Information System (SIS Web) interface.Canceled Part Numbers and Replaced Part Numbers
This document does not include Canceled part numbers and replaced part numbers. Use NPR on SIS for information about Canceled part numbers and replaced part numbers. NPR will provide the current part numbers for replaced parts.Important Safety Information
Illustration 1 g02139237Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly. Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. Therefore, the warnings in this publication and the warnings that are on the product are not all inclusive. If a tool, a procedure, a work method, or operating technique that is not recommended by Caterpillar is used, ensure that it is safe for you and for other people to use. Ensure that the product will not be damaged or the product will not be made unsafe by the operation, lubrication, maintenance, or the repair procedures that are used.
Improper operation, lubrication, maintenance or repair of this product can be dangerous and could result in injury or death.Do not operate or perform any lubrication, maintenance or repair on this product, until you have read and understood the operation, lubrication, maintenance and repair information.
Safety precautions and warnings are provided in this manual and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons.The hazards are identified by the safety alert symbol which is followed by a signal word such as danger, warning, or caution. The "" safety alert symbol is shown below.
Illustration 2 g00008666This safety alert symbol means:Pay attention!Become alert!Your safety is involved.The message that appears under the safety alert symbol explains the hazard.Operations that may cause product damage are identified by "" labels on the product and in this publication.Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. The safety information in this document and the safety information on the machine are not all inclusive. Determine that the tools, procedures, work methods, and operating techniques are safe. Determine that the operation, lubrication, maintenance, and repair procedures will not damage the machine. Also, you must determine that the operation, lubrication, maintenance, and repair procedures will not make the machine unsafe.The information, the specifications, and the illustrations that exist in this guideline are based on information which was available at the time of publication. The specifications, torques, pressures, measurements, adjustments, illustrations, and other items can change at any time. These changes can affect the service that is given to the product. Obtain the complete, most current information before you start any job. Caterpillar dealers can supply the most current information.Summary
This guideline should be used for inspecting and measuring the components of a used engine oil pump, reconditioned engine oil pump, and front housings. This inspection and the measurement will determine if an engine oil pump can be used again. Often, the installation of a new engine oil pump is not necessary during an engine rebuild. The installation of a used oil pump or reconditioned oil pump can decrease costs of the engine rebuild. An engine oil pump that meets these guidelines for inspection and specifications can be expected to give normal performance in the same application until the next overhaul.If this guideline indicates a part that cannot be used again, then never reuse the part. Individual components must be ch