5030056 EVINRUDE WASHER, Fuel tank


5030056 WASHER, Fuel tank EVINRUDE E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC, E5RECS, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA WASHER
5030056 WASHER, Fuel tank EVINRUDE
Rating:
58

Buy WASHER, Fuel tank 5030056 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 15
 

BRP EVINRUDE entire parts catalog list:

E25EL4SIC, E25PL4SIC, E25R4SIC, E25RL4SIC, E25TE4SIC, E25TEL4SIC 2001
E25EL4SSS, E25PL4SSS, E25R4SSS, E25RL4SSS, E25TE4SSS, E25TEL4SSS 2000
E30EL4SIC, E30PL4SIC, E30R4SIC, E30RL4SIC, E30TE4SIC, E30TEL4SIC 2001
E30EL4SSS, E30PL4SSS, E30R4SSS, E30RL4SSS, E30TE4SSS, E30TEL4SSS 2000
E40PL4EES 1999
E40PL4SIR 2001
E40PL4SSC 2000
E50PL4EES 1999
E50PL4EES 1999
E50PL4SIR 2001
E50PL4SIR 2001
E50PL4SSC 2000
E50PL4SSC 2000
E5RECS, E5RLECS 1998
E70, E70PL4SSR 2000
E70FLTLECS 1998
E70PL4EEC 1999
E70PL4SIA 2001

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-8376 Cap Kit 1 Start By:
If necessary, remove the secondary fuel filter and the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install" for the correct procedure.
If necessary, remove the water separator and fuel filter (Primary). Refer to Disassembly and Assembly, "Water Separator and Fuel Filter (Primary) - Remove and Install" for the correct procedure.
Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install" for the correct procedure.
Remove the crankcase breather cannister and plastic tube assemblies. Refer to Disassembly and Assembly, "Crankcase Breather - Remove" for the correct procedure.
Remove the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold (Rail) - Remove and Install" for the correct procedure.
Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" for the correct procedure.
Remove the mounting bracket for the electronic control module. Refer to Disassembly and Assembly, "E.C.M. Mounting Bracket - Remove and Install" for the correct procedure.
Remove the glow plugs. Refer to Disassembly and Assembly, "Glow Plugs - Remove and Install" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining procedure.
Illustration 1 g02005213
Disconnect the upper radiator hose from water temperature regulator housing (1) on the cylinder head.
Illustration 2 g02206193
Remove plastic tube assembly (2), plastic tube assembly (3), and plastic tube assembly (7) from clips (9).
Cut all cable straps (5) from engine wiring harness assembly (6). Position engine wiring harness assembly away from the engine. Note: Ensure that all cable straps are removed from the engine wiring harness.
Remove bolts (8) and remove bracket (4) from the cylinder head.
Illustration 3 g02206194
Follow Step 6.a through Step 6.b in order to disconnect harness assembly (15) from boost pressure sensor (13).
Slide locking tab (14) into the unlocked position.
Disconnect harness assembly (15) from boost pressure sensor (13).
Follow Step 7.a through Step 7.b in order to disconnect harness assembly (11) from inlet air temperature sensor (10).
Slide locking tab (12) into the unlocked position.
Disconnect harness assembly (11) from inlet air temperature sensor (10).
Remove all cable straps that secure the harness assembly to the cylinder head. The harness assembly should be positioned away from the cylinder head in order to avoid causing an obstruction during the removal of the cylinder head.
On some application there is an engine wiring harness support bracket on the rear of the cylinder head. if necessary, cut the cable straps and remove the engine wiring harness from the support bracket. Remove the support bracket from the cylinder head before removal the cylinder head assembly.
Illustration 4 g02206213
Remove bolt (16) from tube assembly (18). Remove bolt (20) from tube clip (19).
Remove tube assembly (18) from the cylinder head. Remove O-ring seal (17) (not shown) from the tube assembly. Plug the port in the cylinder head with a new plug. Cap the tube assembly with new cap.
Illustration 5 g02206214
Follow Step 12.a through Step 12.c in order to disconnect harness assembly (22) from coolant temperature sensor (23).
Slide locking tab (21) into the unlocked position.
Disconnect harness assembly (22) from coolant temperature sensor (23).
Cut cable strap (26) and remove harness assembly (22) from bypass tube (25).
Remove bolts (24).
Remove bypass tube (25) from the cylinder head. Remove O-ring seal (27) and O-ring seal (28) from bypass tube (25).
Illustration 6 g02206215
Illustration 7 g02206216
Sequence for tightening the bolts for the cylinder head
Gradually loosen bolts (29) in the reverse numerical order to the tightening sequence. Refer to the Illustration 7. Note: Follow the correct sequence in order to help prevent distortion of the cylinder head.
Remove bolts (29) from


Parts washer EVINRUDE:

5030070
5030451
 
5030451 WASHER, (2.6mm)
E70, E70FLTLECS, E70PL4EEC
5030445
 
5030445 WASHER, (1.7mm)
E70, E70FLTLECS, E70PL4EEC
5030428
 
5030428 WASHER, Bolt, holder
E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030439
 
5030439 WASHER, Bolt, pulley
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5031460
 
5031460 WASHER SET
E40PL4EES, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SSC, E50PL4SSC, E70
5031833
 
5031833 WASHER, Hook
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5030430
 
5030430 WASHER
E70PL4SIA
Back to top