0393082 WATER PUMP REPAIR KIT EVINRUDE
E100WMLCRS, E115MLCNB, E115MLCRD, E115MLCTE, E140MLCNB, E140MLCTE, E140TLCRD, E150ANCRS, E150STLCTE, E150TLCRD, E150TRLCNM, E150TRLCTB, E155WTLCRS, E175TRLCNB, E175TRLCTD, E185TLCRS, E200TRLCNE, E200TRLCTD, E235STLCRC, E235STLCTS, E235TLCRC, E235TRLC
WATER
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
WKZO 5001594 0434421 18-3392 Outboard Water Pump Impeller Repair Kit For Johnson Evinrude V4 V6 V8 85 90 115 120 130 135 140 150 175 200 225 250 300 HP 0390768 0391637 0392750 0393082 0395060 0395062
WKZO 5001594 Water Pump Kits are manufactured using high quality raw materials || In order to prevent purchasing the wrong unsuitable part, which could result in wasted time, you need to determine suitability by using the information on the engine nameplate || 140hp(1979-1981); 150 / 175 / 200 / 235(1979-1981); V4 / V6 / V8(1982 – 1992), for more applicable types, please refer to the picture details. || Replacing part numbers: 5001594 , 0390768 , 0391637 , 0392750 , 0393082 , 0395060 , 0395062 , 0435447 , 0434421 , Sierra 18-3392 || Original level of quality and durability, the impellers are manufactured from high quality rubber and will not be damaged even after long periods of immersion in salt water
WKZO 5001594 Water Pump Kits are manufactured using high quality raw materials || In order to prevent purchasing the wrong unsuitable part, which could result in wasted time, you need to determine suitability by using the information on the engine nameplate || 140hp(1979-1981); 150 / 175 / 200 / 235(1979-1981); V4 / V6 / V8(1982 – 1992), for more applicable types, please refer to the picture details. || Replacing part numbers: 5001594 , 0390768 , 0391637 , 0392750 , 0393082 , 0395060 , 0395062 , 0435447 , 0434421 , Sierra 18-3392 || Original level of quality and durability, the impellers are manufactured from high quality rubber and will not be damaged even after long periods of immersion in salt water
Industrial Rollers, Bearings, and Belts and Much More - Replacement for Water Pump Rebuild Kit for OMC for Johnson for Evinrude 0392750, 0393082, 0395062 for Engine
Generic Industrial Rollers, Bearings, and Belts and much more - Replacement for Water Pump Rebuild Kit For OMC For Johnson For Evinrude 0392750, 0393082, 0395062 For Engine
Generic Industrial Rollers, Bearings, and Belts and much more - Replacement for Water Pump Rebuild Kit For OMC For Johnson For Evinrude 0392750, 0393082, 0395062 For Engine
Automobiles Outboard Motor Water Pump Impeller Kit Compatible With Models 5001594 395060 0390768 0434421 0393082 For 3-300
ShUDK Model Compatibility: Designed for use with various outboard motors ranging from 3-300 . || Efficient Cooling: Ensures effective water flow to prevent overheating of your outboard motor. || Versatile Use: Suitable for a range of applications in recreational and commercial boating. || Enhanced Performance: Optimizes water pump function for improved overall engine efficiency. || Complete Kit: Includes all necessary components for a straightforward replacement process.
ShUDK Model Compatibility: Designed for use with various outboard motors ranging from 3-300 . || Efficient Cooling: Ensures effective water flow to prevent overheating of your outboard motor. || Versatile Use: Suitable for a range of applications in recreational and commercial boating. || Enhanced Performance: Optimizes water pump function for improved overall engine efficiency. || Complete Kit: Includes all necessary components for a straightforward replacement process.
Compatible models:
BRP EVINRUDE entire parts catalog list:
- GEARCASE » 0393082
E115MLCRD, E115TLCRD, E115TXCRD 1984
E115MLCTE, E115TLCTE, E115TXCTE 1983
E140MLCNB, E140TRLCNB, E140TRXCNB 1982
E140MLCTE, E140TRLCTE, E140TRXCTE 1983
E140TLCRD, E140TXCRD 1984
E150ANCRS, E150STLCRD 1984
E150STLCTE 1983
E150TLCRD, E150TXCRD 1984
E150TRLCNM, E150TRXCNM 1982
E150TRLCTB, E150TRLCTE, E150TRXCTB, E150TRXCTE 1983
E155WTLCRS, E155WTXCRS 1984
E175TRLCNB, E175TRXCNB 1982
E175TRLCTD, E175TRLCTE, E175TRXCTD, E175TRXCTE 1983
E185TLCRS, E185TXCRS 1984
E200TRLCNE, E200TRXCNE 1982
E200TRLCTD, E200TRLCTS, E200TRXCTD, E200TRXCTS 1983
E235STLCRC 1984
E235STLCTS 1983
E235TLCRC, E235TXCRC 1984
E235TRLCNE, E235TRXCNE 1982
E235TRLCTD, E235TRLCTS, E235TRXCTD, E235TRXCTS 1983
E90MLCNB, E90TLCNB, E90TXCNB 1982
E90MLCRD, E90TLCRD, E90TXCRD 1984
E90MLCTE, E90TLCTE, E90TXCTE 1983
Information:
Probable Causes
Codes
Parameters
Throttle Signal
Air Inlet and Exhaust System
Fuel System
Engine Load
Valve LashRecommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load, and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.
Table 1
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
Codes
Result: A diagnostic code is present.
Repair: Troubleshoot the code.
Result: A diagnostic code is not present.
Proceed to Test Step 2.
2. Incorrect Parameters
A. Use Cat ET to verify that the correct parameters are being used. Refer to Troubleshooting, "Configuration Parameters" for additional information.
Parameters Result: The parameters are correct.
Proceed to Test Step 3.
Result: The parameters are not correct.
Repair: Input the correct parameters. Refer to Troubleshooting, "Configuration Parameters" for additional information.
3. Throttle Signal
A. Monitor the status for "Throttle Position" on Cat ET. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed.
Throttle Signal Result: The throttle signal is stable.
Proceed to Test Step 4.
Result: The throttle signal is not stable.
Repair: Make the necessary repairs, Refer to the appropriate circuit test.
4. Restriction in the Air Inlet and Exhaust System
A. Observe the check engine lamp. Check for an air filter restriction indicator. Replace any plugged air filters. Refer to the Operation and Maintenance Manual.
B. Check the air inlet and exhaust system for restrictions and/or leaks.
Restrictions Result: There are no restrictions in the air inlet or exhaust system.
Proceed to Test Step 5.
Result: There are restrictions in the air inlet or exhaust system.
Repair: Make the necessary repairs, Refer to Systems Operation/Testing and Adjusting, "Air Inlet and Exhaust System - Inspect" for additional information.
5. Check the Fuel System
Refer to Systems Operation/Testing and Adjusting, "Fuel System" for additional information.
A. Visually check the fuel level in the fuel tank. Do not rely on the fuel gauge only.
B. Ensure that the vent in the fuel cap is not filled with debris.
C. Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
D. Inspect the fuel system. Refer to Systems Operation/Testing and Adjusting, "Fuel System - Inspect" for additional information.
E. Cold weather adversely affects the characteristics of the fuel. Refer to the engines Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold-weather operation. Cold mode (if applicable) is activated whenever the engine coolant temperature falls below a predetermined value. Monitor the status screen on Cat ET in order to verify that the engine has exited cold mode. Observe the reading for coolant temperature on the Cat ET.
Refer to "Cold Mode Operation" within the Systems Operation, "General Information".
F. Check fuel quality. Refer to Systems Operation/Testing and Adjusting, "Fuel Quality - Test" for the proper procedure. Check the fuel tank for debris or foreign objects which may block the fuel supply.
G. Check for the proper operation of the fuel transfer pump. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for test information.
Fuel system Result: The fuel pressure is OK.
Proceed to Test Step 6.
Result: The fuel pressure is not OK.
Repair: Replace the fuel filters. Clean the primary filter/water separator of debris. Refer to the Operation and Maintenance Manual for details.
6. Engine Load
A. Check accessories and parasitic loads on the engine.
Engine loads Result: There is not a parasitic load.
Proceed to Test Step 7.
Result: There is a parasitic load.
Repair: Remove the parasitic load.
7. Valve Lash
A. Check the valve lash. The valve lash can affect the performance of the engine.
Valve lash Result: The valve lash is not set correctly.
Repair: Set the valve lash. Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for the correct procedure.
STOP
Codes
Parameters
Throttle Signal
Air Inlet and Exhaust System
Fuel System
Engine Load
Valve LashRecommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load, and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.
Table 1
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
Codes
Result: A diagnostic code is present.
Repair: Troubleshoot the code.
Result: A diagnostic code is not present.
Proceed to Test Step 2.
2. Incorrect Parameters
A. Use Cat ET to verify that the correct parameters are being used. Refer to Troubleshooting, "Configuration Parameters" for additional information.
Parameters Result: The parameters are correct.
Proceed to Test Step 3.
Result: The parameters are not correct.
Repair: Input the correct parameters. Refer to Troubleshooting, "Configuration Parameters" for additional information.
3. Throttle Signal
A. Monitor the status for "Throttle Position" on Cat ET. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed.
Throttle Signal Result: The throttle signal is stable.
Proceed to Test Step 4.
Result: The throttle signal is not stable.
Repair: Make the necessary repairs, Refer to the appropriate circuit test.
4. Restriction in the Air Inlet and Exhaust System
A. Observe the check engine lamp. Check for an air filter restriction indicator. Replace any plugged air filters. Refer to the Operation and Maintenance Manual.
B. Check the air inlet and exhaust system for restrictions and/or leaks.
Restrictions Result: There are no restrictions in the air inlet or exhaust system.
Proceed to Test Step 5.
Result: There are restrictions in the air inlet or exhaust system.
Repair: Make the necessary repairs, Refer to Systems Operation/Testing and Adjusting, "Air Inlet and Exhaust System - Inspect" for additional information.
5. Check the Fuel System
Refer to Systems Operation/Testing and Adjusting, "Fuel System" for additional information.
A. Visually check the fuel level in the fuel tank. Do not rely on the fuel gauge only.
B. Ensure that the vent in the fuel cap is not filled with debris.
C. Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
D. Inspect the fuel system. Refer to Systems Operation/Testing and Adjusting, "Fuel System - Inspect" for additional information.
E. Cold weather adversely affects the characteristics of the fuel. Refer to the engines Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold-weather operation. Cold mode (if applicable) is activated whenever the engine coolant temperature falls below a predetermined value. Monitor the status screen on Cat ET in order to verify that the engine has exited cold mode. Observe the reading for coolant temperature on the Cat ET.
Refer to "Cold Mode Operation" within the Systems Operation, "General Information".
F. Check fuel quality. Refer to Systems Operation/Testing and Adjusting, "Fuel Quality - Test" for the proper procedure. Check the fuel tank for debris or foreign objects which may block the fuel supply.
G. Check for the proper operation of the fuel transfer pump. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for test information.
Fuel system Result: The fuel pressure is OK.
Proceed to Test Step 6.
Result: The fuel pressure is not OK.
Repair: Replace the fuel filters. Clean the primary filter/water separator of debris. Refer to the Operation and Maintenance Manual for details.
6. Engine Load
A. Check accessories and parasitic loads on the engine.
Engine loads Result: There is not a parasitic load.
Proceed to Test Step 7.
Result: There is a parasitic load.
Repair: Remove the parasitic load.
7. Valve Lash
A. Check the valve lash. The valve lash can affect the performance of the engine.
Valve lash Result: The valve lash is not set correctly.
Repair: Set the valve lash. Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for the correct procedure.
STOP
Parts water EVINRUDE:
0321015
0321015 WATER TUBE
115790S, 150840S, 150940C, 175740S, 200640S, BE130TLECE, BE130TLEDM, BE130TLEUB, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, C155WTLM, E120TLCCA, E120TLCDC, E120TLCEM, E120TLCOS, E120TLCUR, E120TLEIE, E120TLEND, E120TLERC,
0321016
0321016 WATER TUBE
115790S, 150840S, 150940C, 175740S, 200640S, BE130TLECE, BE130TLEDM, BE130TLEUB, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, C155WTLM, E120TLCCA, E120TLCDC, E120TLCEM, E120TLCOS, E120TLCUR, E120TLEIE, E120TLEND, E120TLERC,
0323403
0323403 WATER TUBE
100990S, 115890C, BE115TLEDA, E100MLCSC, E100STLCCA, E100STLCEM, E100STLEIE, E100STLEND, E100STLERC, E100STLESB, E100STLETS, E100WMLCDR, E100WMLCOC, E100WMLCRS, E100WTLCUA, E100WTLEDR, E100WTLEIB, E100WTLENE, E100WTLEOC, E100WTLERS, E100WTLESM, E100W
0323404
0323404 WATER TUBE
100990S, 115890C, BE115TLEDA, E100MLCSC, E100STLCCA, E100STLCEM, E100STLEIE, E100STLEND, E100STLERC, E100STLESB, E100STLETS, E100WMLCDR, E100WTLCUA, E100WTLEDR, E100WTLEIB, E100WTLENE, E100WTLEOC, E100WTLERS, E100WTLESM, E100WTLETD, E100WTLEUA, E100W
0390768
0390768 WATER PUMP REPAIR KIT
100990S, E100MLCSC, E115MLCIH, E115MLCNB, E115MLCSA, E140MLCIH, E140MLCNB, E140MLCSA, E150TRLCIA, E150TRLCNM, E150TRLCSF, E175TRLCIM, E175TRLCNB, E175TRLCSA, E200TRLCIB, E200TRLCNE, E200TRLCSF, E235TRLCIB, E235TRLCNE, E235TRLCSM, E85MLCSA, E90MLCIH,
0391637
0391637 WATER PUMP REPAIR KIT (Includes impeller
E100MLCSC, E115MLCIH, E115MLCNB, E115MLCSA, E140MLCIH, E140MLCNB, E140MLCSA, E150TRLCNM, E175TRLCNB, E200TRLCNE, E235TRLCNE, E85MLCSA, E90MLCIH, E90MLCNB
0392750
0392750 WATER PUMP REPAIR KIT (INCLUDES IMP HSG. 2
E100WMLCRS, E115MLCNB, E115MLCRD, E115MLCTE, E140MLCNB, E140MLCTE, E140TLCRD, E150ANCRS, E150STLCTE, E150TLCRD, E150TRLCNM, E150TRLCTB, E175TRLCNB, E175TRLCTD, E185TLCRS, E200TRLCNE, E200TRLCTD, E235STLCRC, E235STLCTS, E235TLCRC, E235TRLCNE, E235TRLC