F663095-4 Force STATOR ASSEMBLY


F663095-4 STATOR ASSEMBLY Force H0507A91C, H0903E91H, H0903F91A, H0903F91C, H1201A90A STATOR
F663095-4 STATOR ASSEMBLY Force
Rating:
73

Buy STATOR ASSEMBLY F663095-4 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Force entire parts catalog list:

H0507A91C 1991
H0903E91H 1991,1992,1993,1994
H0903F91A 1991
H0903F91C 1991
H1201A90A 1990,1991,1992,1993,1994

Information:

Start By:a. remove engine balancer group (3114 Engines)b. remove oil pump (3116 Engines) 1. Remove bolts (1), the washers and bearing cap (2). Remove the lower main bearing half from the cap.
If the crankshaft is turned in the wrong direction during upper main bearing half removal, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This can cause result in damage to either or both the crankshaft and the cylinder block.
Both the center and two end main journals have no oil hole. To remove these upper main bearing halves, put a thin piece of soft material, (that will not damage the crankshaft journal), against the end of the bearing half, opposite the tab. Hit the bearing with the soft material until the tab of the bearing is free from the groove in the cylinder block.2. Remove the upper half of the main bearings as follows: a. Turn the crankshaft until Tool (A) can be installed in the crankshaft journal. Install Tool (A) as shown.b. Turn the crankshaft in the direction which will push the upper main bearing half out, tab end first.c. Check the condition of the main bearings. Refer to "Guideline For Reusable Parts, Main & Connecting Rod Bearings", Form No. SEBF8009 and SEBD0531 as guide for checking bearing condition. The following steps are for the installation of the crankshaft main bearings.3. Clean the bearing surfaces in the cylinder block for the main bearings. Apply clean engine oil on the upper main bearing half. Do not put oil on the back side of the bearing. Using Tool (A), install the upper main bearing half (bearings with the oil holes) in the cylinder block. Be sure the tab on the back side of the bearing engages with the groove in the cylinder block.4. Clean the bearing surface of the main bearing caps. Install the lower main bearing half in the main bearing cap. Be sure the tab on the back side of the bearing engages with the groove in the main bearing cap. Apply clean engine oil on the lower main bearing half. Do no put oil on the back side of the bearing.5. Install the main bearing caps as follows:
Install the main bearing caps with the sequence number to the right, 1 through 5 (for the 4 cylinder) and 1 through 7 (for the 6 cylinder), front to rear.
a. Put main bearing caps (2) in position in the cylinder block with the sequence numbers in the correct positions.b. Apply clean engine oil to the threads of the main bearing cap mounting bolts and on the washer contact faces.c. Install main bearing cap mounting bolts (1) and the washers. Tighten both bolts of each main bearing cap to a torque of 54 7 N m (40 5 lb ft).d. Tighten the bolts and additional 1/4 90 5 degrees ( turn). 6. Check the end play of the crankshaft with Tool (B). The end play of the crankshaft (3114) must be 0.07 to 0.29 mm (.003 to .011 in). The end play of the crankshaft (3116) must be 0.07 to 0.32 mm (.003 to .013 in).End By:a. install oil pump (3116 Engines)b. install engine balancer group (3114 Engines)


Parts stator Force:

8778A23
8778A27
8778A29
STATOR ASSEMBLY
8778A29 STATOR ASSEMBLY
H0706A91B, H090312RD, H0903E91H
8778A10
 
8778A10 STATOR ASSY. (91B Thru 92C)
H0706A91B, H0903E91D, H0903E91H
8778A26
STATOR ASSEMBLY
8778A26 STATOR ASSEMBLY
H0706A91B, H0903E91H
Back to top