F15177 ARMATURE* Force
H0606H84A, H0706A91B, H075312SD, H075312UD, H075412VD, H0851X88A, H0853F88B, H0853F89C, H0853F89E, H0853F89F, H0853F89G, H0856A89A, H0856A89H, H0856C87A, H0856C87B, H0856F84A, H0856F85A, H0856F86A, H0856L89D, H0856Y89B, H0858C84H, H085LD89A, H085LD89
ARMATURE
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$57.95
20-07-2024
6.0[2.70] pounds
US: Race-Driven Inc
1986 1987 Fits Honda TRX250R TRX 250R Red Chain and Silver Sprocket 12/39 96L
Race-Driven 12 Tooth Front Sprocket, 39 Tooth Rear Sprocket and 520-96L Red Non-O-Ring Chain || All Race-Driven sprockets meet or exceed OEM specifications and use hardened S45C steel. || Non-O-Ring chain doesn't have o-rings between the links so it is lighter, thinner and has less drag. || Fits 1986 1987 Honda TRX250R
Race-Driven 12 Tooth Front Sprocket, 39 Tooth Rear Sprocket and 520-96L Red Non-O-Ring Chain || All Race-Driven sprockets meet or exceed OEM specifications and use hardened S45C steel. || Non-O-Ring chain doesn't have o-rings between the links so it is lighter, thinner and has less drag. || Fits 1986 1987 Honda TRX250R
Compatible models:
H0606H84A
H0706A91B
H075312SD
H075312UD
H075412VD
H0851X88A
H0853F88B
H0853F89C
H0853F89E
H0853F89F
H0853F89G
H0856A89A
H0856A89H
H0856C87A
H0856C87B
H0856F84A
H0856F85A
H0856F86A
H0856L89D
H0856Y89B
H0858C84H
H085LD89A
H085LD89B
H085LD89C
H090312RD
H0903E91D
H0903E91H
H0903F90B
H0903F90C
H0903F91A
H0903F91C
H090412SD
H090412UD
H090422VD
H0906A90A
H090LD90A
H090LD90B
H090LD90C
H090LD91D
H1201A90A
H120412RD
H120412SD
H120412UD
H120LD90A
H120LD90B
H120LD90C
H120LD91B
H120LD91D
H120LD92B
H1251A88A
H1251A88B
H1251A88C
H1251A89A
H1251A89B
H1251A89C
H1251A89D
H1251A89E
H1251F84A
H1251F86A
H1251F87A
H1251F87B
H1251X85A
H125LD89A
H125LD89B
H1408H83E
H1501E89A
Force
Force entire parts catalog list:
- STARTER » F15177
- STARTER » F15177
- STARTER ASSEMBLY » F15177
- STARTER ASSEMBLY » F15177
- STARTER MOTOR ASSEMBLY » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER ASSEMBLY » F15177
- STARTER » F15177
- STARTER ASSEMBLY » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER ASSEMBLY » F15177
- STARTER ASSEMBLY » F15177
- STARTER MOTOR ASSEMBLY » F15177
- STARTER ASSEMBLY » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER ASSEMBLY » F15177
- STARTER ASSEMBLY » F15177
- STARTER ASSEMBLY » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER (BOSCH) » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
- STARTER » F15177
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 298-5564 T40 Torx Socket 1
D 1U-5718 Vacuum Pump 1
169-7372 Fluid Sampling Bottle 1
4C-4057 Tube
7.9 mm (0.31 inch) Outside Diameter 1
E 336-0703 Injector Pipe Nut Tool 1
F 247-5377 Torque Wrench 1
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorised personnel that have the correct training.Before begining ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Use a deep socket to install the electrical connections to the electronic unit injectors. Use of incorrect tooling will result in damage to the electronic unit injectors.
Illustration 1 g02353356
Injector code
If the original electronic unit injector (8) is installed , ensure that the electronic unit injector is installed into the original position.
If a replacement electronic unit injector is installed, the correct injector code must be programmed into the electronic control module. Refer to Troubleshooting, "Injector Code - Calibrate" for more information. The code that is required is located at Position (X).Note: Record Code (X) before the electronic unit injector is installed.
Use Tooling (D) to remove any fuel from the cylinder.Note: Evacuate as much fuel as possible from the cylinder before installing the electronic unit injector.
Illustration 2 g02313273
If necessary, follow Step 4a through Step 4e to install a new harness assembly (6) to cylinder head (16).
Install a new harness assembly (6) to cylinder head (16).Note: Do not lubricate the O-ring seal.
Install a new bolt (14) to harness assembly (6). Tighten the bolt to a torque of 5.5 N m (49 lb in).
Install new assemblies of cable strap (13) for harness assembly (6) to cylinder head (16).Note: Ensure that the assemblies of the cable strap are correctly installed into the cylinder head.
Connect harness assembly (15) to harness assembly (6).
If necessary, repeat Step 4a through Step 4e to install the remaining harness assemblies to the cylinder head.
Ensure that the fuel inlet port of the electronic unit injector is capped. Ensure that the electronic unit injector is clean.
Illustration 3 g01972153
New sealing washer (12) should only be installed if the original electronic unit injector (8) is to be reused.
On installing an original electronic unit injector, install a new O-ring seal (11).Note: Do not lubricate the O-ring seal.
Use a suitable tool to install a new sealing washer (12) to electronic unit injector (8).Note: Ensure that the nozzle for the electronic unit injector is not damaged in any way on installation of the new sealing washer.
Ensure that O-ring seal (11) and sealing washer (12) on a new electronic unit injector are not damaged and in place.Note: Do not lubricate the O-ring seal.
Ensure that the seat for the electronic unit injector in the cylinder head is clean and free from damage. Ensure that the sealing washer has been removed from the cylinder head.
Illustration 4 g01971773
Position clamp (10) onto electronic unit injector (8). Align the assembly of electronic unit injector (8) to the bore for the electronic unit injector in the cylinder head.Note: Ensure that the clamp is correctly positioned onto the electronic unit injector.
Push only on injector clamp (10) to install electronic unit injector (8). Do not apply pressure on any other part of the electronic unit injector. Ensure that the electronic unit injector is pushed firmly against the seat in the cylinder head.
Install a new Torx screw (9) to clamp (10). Tighten the Torx screw finger tight.
Remove the cap from electronic unit injector (8). Install a new seal (4) to electronic unit injector (8) and to the cylinder head. Ensure that the flange on the seal is flush with the cylinder head.
Remove the plugs from the new fuel injection line. Install the fuel injection line hand tight. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install" for the correct procedure.Note: Ensure that the ends of the fuel injection line are seated into the electronic unit injector and the fuel manifold. Tighten the nuts hand tight.
Use Tooling (A) to tighten Torx screw (9) to a torque of 21 N m (186 lb in).Note: Tooling (A) must be used to ensure no damage to the electronic unit injector.
Use Tooling (E) to tighten the fuel injection line to a torque of 50 N m (37 lb ft). Refer to Disassembly and Assembly, "Fuel Injection Lines - I
Parts armature Force:
F15099
F15099 ARMATURE
H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0659B78B, H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80
F17555
F17555 ARMATURE
H0606H84A, H0700H79A, H0750H79A, H0756H81G, H0756H82H, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0855H79A, H0856C87A, H0856H82K, H0858B80C, H0858B82E, H0858C84H, H0859B79B, H0859H77A, H0859H78A, H0906R83D, H1000H79
813449A 1
820546
811700
811627 1