286169 Force BEARING LOWER SWIVEL BRACKET


286169 BEARING LOWER SWIVEL BRACKET Force H0092S91A, H0093S91A BEARING
286169 BEARING LOWER SWIVEL BRACKET Force
Rating:
48

Buy BEARING LOWER SWIVEL BRACKET 286169 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 27
 

Compatible models:

Force entire parts catalog list:

Information:

(1) Maximum length of pin out of crankshaft face ... 6.4 mm (.25 in.)(2) Thrust plates for center main bearing only.(3) End play for the crankshaft (new) ... 0.13 to 0.50 mm (.005 to .020 in.)Maximum permissible end play with used bearings ... 0.89 mm (.035 in.)(4) Minimum torque for six plugs ... 23 N m (17 lb.ft.) "Stake" (make a mark with a punch) the crankshaft to hold the plug tight.(5) Length of dowel out of the crankshaft ... 4.1 0.5 mm (.16 .02 in.)(6) Maximum permissible temperature of the gear for installation on the crankshaft ... 205° C (400° F) Install gear with timing "V" mark to the outside.(7) 2W1734 Seal Group (rear) installed on rear crankshaft gear.(8) Make reference to CONNECTING ROD BEARINGS.(9) Make reference to MAIN BEARINGS.(10) 2W1733 Seal Group (front). Remove front and rear seal groups as follows: Seals and wear sleeves can not be used again, after the seals and wear sleeves are separated.a. Use the 1P3075 Puller Group to remove the seals.b. Use the 5P7318 Distorter Group to remove the wear sleeves. Install front and rear seal groups as follows:a. Clean the outer surface of the crankshaft with 6V1541 Quick Cure Primer.b. Crankshaft seals must be installed with the lip of the seal toward the inside of the engine as shown. Make sure the correct seal is installed on each end of the crankshaft. Use 2W1733 Seal Group on the front and 2W1734 Seal Group on the rear. No lubrication is needed to install wear sleeves and seals.c. Do not separate seals from sleeves. Install the seal groups as a unit on each end of the engine as shown with the correct tools. See Special Instruction Form Nos. SMHS8508 and SMHS8008 for the necessary tools and complete procedure for installation of front and rear seal groups.Earlier Engine Crankshaft Groups
(1) Maximum length of pin out of crankshaft face ... 6.4 mm (.25 in.)(2) Thrust plates, at center main bearing.(3) End play for the crankshaft (new) ... 0.15 to 0.50 mm (.006 to .020 in.)(4) Minimum torque for six plugs ... 23 N m (17 lb.ft.) "Stake" (make a mark with a punch) the crankshaft to hold the plug tight.(5) Length of dowel out of the crankshaft ... 4.1 0.5 mm (.16 .02 in.)(6) Maximum permissible temperature of the gear for installation on the crankshaft ... 232° C (450° F) Install gear with "V" mark to the outside.(7) Rear gear wear sleeve and seal (on rear crankshaft gear). For removal and installation procedure, see (10).(8) Make reference to CONNECTING ROD BEARING JOURNALS.(9) Make reference to MAIN BEARING JOURNALS.(10) Front wear sleeve and seal: Remove wear sleeves with 5P7318 Distorter Group.Install front and rear wear sleeves and seals as follows:a. Clean the inner surface of the sleeve and the outer surface of the crankshaft (front) or crankshaft gear (rear) with 6V1541 Quick Cure Primer.b. Put 9S3265 Retaining Compound on the cleaned surfaces.c. Install the sleeve and seal at the same time on the crankshaft or crankshaft gear as shown. See Special Instruction Form SMHS7100 for the necessary tools and complete procedure for installation of wear sleeves and seals.


Parts bearing Force:

F343014
 
F343014 BEARING, CRANKSHAFT LOWER MAIN
H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062H79K, H0062H79M, H0064H78D, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0072B81D, H0072H79B, H0072H80C, H0072H82E, H0075H79A, H0082H76G, H0082H79K, H0091B80B, H0091H79A, H0091H83
F197319
 
F197319 BEARING, CHOKE ROD
H0091B80B, H0091H79A, H0091H83C, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092B80G, H0092H79F, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0101B78A, H0102H76C, H0102H78E, H0121B79
F286028
 
F286028 BEARING, CRANKSHAFT UPPER MAIN
H0064H82H, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H82E, H0091H83C, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0094H81F, H0095B81
F536813
 
F536813 BEARING
H0060H79C, H0060H80D, H0064H80F, H0064H82H, H0067H79C, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H80C, H0072H82E, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092B80G, H0092H79
85610
 
85610 BEARING
H0092S91A, H0093S91A, H0503B83A, H0507E91B
286028
343014
183813
Back to top