818060A 1 BEARING CAGE LOWER W/SEALS Force
H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0606H84A, H0659B78B
BEARING
Price: query
Rating:
Compatible models:
Force entire parts catalog list:
- CRANKSHAFT AND PISTON GROUP » 818060A 1
- CRANKSHAFT AND PISTON GROUP » 818060A 1
- CRANKSHAFT AND PISTON GROUP » 818060A 1
- CRANKSHAFT AND PISTON GROUP » 818060A 1
- CRANKSHAFT AND PISTON GROUP » 818060A 1
- CRANKSHAFT AND PISTON GROUP » 818060A 1
- CRANKSHAFT AND PISTON GROUP » 818060A 1
- CRANKSHAFT AND PISTON GROUP » 818060A 1
- CRANKSHAFT AND PISTON GROUP » 818060A 1
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Prior to removal of the flywheel, position the number one piston in the top center position (TC). The engine should be at the top center position in order to properly install the rear gear group. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Illustration 1 g02087895
(X) Marker
(Y) Alignment Mark
With the number one piston in the top center position (TC), attach a Marker to the engine and place an Alignment Mark on the vibration damper.
Remove the flywheel housing.
Illustration 2 g01151801
Remove bolts (10), thrust plate (11), and gear assembly (9).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (9).
Remove bolts (8), gear assembly (6), and shaft assembly (7).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (6).
Remove bolts (2), gear assembly (1), and shaft assembly (3).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (1).
Remove gear assembly (12).
Remove bolts (5) and gear assemblies (4).
Illustration 3 g01151842
Remove bolts (16) and shaft assembly (17).
Remove bolts (13), thrust plates (14), and adapter assemblies (15).
Use bolt (13) in order to remove the sealing plates. Remove the O-ring seals. C32 Removal Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Prior to removal of the flywheel, position the number one piston in the top center position (TC). The engine should be at the top center position in order to properly install the rear gear group. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Illustration 4 g02087895
(X) Marker
(Y) Alignment Mark
With the number one piston in the top center position (TC), attach a Marker to the engine and place an Alignment Mark on the vibration damper.
Remove the flywheel housing.
Illustration 5 g03427967
Remove bolts (10), retainer assembly (11), the O-ring seal, and gear assembly (9).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (9).
Remove bolts (8), gear assembly (6), and stub shaft assembly (7).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (6).
Remove bolts (2), gear assembly (1), and stub shaft assembly (3).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (1).
Remove gear assembly (12).
Remove bolts (5) and gear assemblies (4).
Remove gear assembly (13) and the thrust washers.
Parts bearing Force:
F390689
F390689 BEARING
H0033H75C, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0064H82H, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H79B, H0072H80C, H0072H82E, H0082H78J, H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78
F335217-1
F335217-1 BEARING
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0352H77H, H0352H79L, H0353E91A, H0353E91B, H0353H78K, H0353H80M, H0353H81
F85571
F85571 BEARING CAGE W/ROLLER
H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0606H84A, H0659B78B, H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79
FA474228
FA474228 BEARING CAGE W/ROLLERS (SPLIT HALF)
H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0606H84A, H0659B78B
F85689-1
F506250
F522057
F522217