F40689 Force BEARING, TOWERSHAFT


F40689 BEARING, TOWERSHAFT Force H0756H81G, H1406H81D, H1408H82D BEARING
F40689 BEARING, TOWERSHAFT Force
Rating:
98

Buy BEARING, TOWERSHAFT F40689 Force genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$10.29
 

02-04-2023
0.1[0.05] Pounds
-: -
Mercury Marine New OEM Towershaft Bearing, FA98689, F90689, F40689, 23-F40689-1
Supersedes Part #s: FA98689, F90689, F40689 || Sold Each || Please verify your own fitment
Number on catalog scheme: 63
 

Compatible models:

Force entire parts catalog list:

H0756H81G 1981
H1406H81D 1981
H1408H82D 1982

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining procedure.
Illustration 1 g01340072
Typical example
Disconnect the upper radiator hose from water temperature regulator housing (1) on the cylinder head.
Illustration 2 g01340075
Typical example
Remove the air inlet hose from inlet connection (3) on inlet manifold (2).
Follow Steps 4.a and 4.b in order to disconnect harness assembly (4) from coolant temperature sensor (5).
Slide the locking tab into the unlocked position.
Disconnect harness assembly (4) from coolant temperature sensor (5).
Follow Steps 5.a and 5.b in order to disconnect harness assembly (4) from boost pressure sensor (6).
Slide the locking tab into the unlocked position.
Disconnect harness assembly (4) from boost pressure sensor (6).
Follow Steps 6.a and 6.b in order to disconnect harness assembly (4) from inlet air temperature sensor (7).
Slide the locking tab into the unlocked position.
Disconnect harness assembly (4) from inlet air temperature sensor (7).
Remove all cable straps that secure harness assembly (4) to the cylinder head or to the inlet manifold. The harness assembly should be positioned in order to avoid causing an obstruction during the removal of the cylinder head.
Illustration 3 g01340077
Typical example
Loosen the tube clips for tube assembly (8). Remove tube assembly (8) for the fuel return from the cylinder head and from the transfer pump. Plug the port in the transfer pump with a new plug. Cap the tube assembly with new caps.
If the engine has a wastegate solenoid, loosen the tube clips for tube assembly (9). Remove tube assembly (9) from the wastegate solenoid and from the cylinder head. Plug the port in the wastegate solenoid with a new plug. Cap the tube assembly with new caps.
Illustration 4 g01340080
Typical example
Remove bolts (10). Remove bypass tube (11) from the cylinder head. Remove O-ring seals (12) and (13) from bypass tube (11).
Illustration 5 g01340081
Illustration 6 g01340083
Sequence for tightening the bolts for the cylinder head
Gradually loosen bolts (14) in the reverse numerical order to the tightening sequence. Refer to the illustration 6. Note: Follow the correct sequence in order to help prevent distortion of the cylinder head.
Remove bolts (14) from cylinder head (15).
Illustration 7 g01340086
Typical example
Attach a suitable lifting device (16) to cylinder head (15). Support the weight of the cylinder head. The weight of the cylinder head is approximately 66 kg (145.5 lb). Note: A spreader bar must be used in order to distribute the weight of the cylinder head during the lifting operation.
Use suitable lifting device (16) to carefully lift cylinder head (15) off the cylinder block. Note: Do not use a lever to separate the cylinder head from the cylinder block. Take care not to damage the machined surfaces of the cylinder head during the removal procedure.
Place the cylinder head on a surface that will not scratch the face of the cylinder head.


Parts bearing Force:

F483884
 
F483884 BEARING
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352H79L, H0353H78K, H0353H80M, H0353H82P, H0357C86A, H0357C87A, H0357F88A, H0357H83N, H0456B78J, H0456B79
F335217-1
BEARING
F335217-1 BEARING
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0352H77H, H0352H79L, H0353E91A, H0353E91B, H0353H78K, H0353H80M, H0353H81
F85571
BEARING CAGE W/ROLLER
F85571 BEARING CAGE W/ROLLER
H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0606H84A, H0659B78B, H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79
F480818
 
F480818 BEARING, LATCH SHAFT
H0152B78D, H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0855H79A, H0856B80H, H0856H82K, H0857B78F, H0857H79
F438169
 
F438169 BEARING
H0700H79A, H0709B79A, H0750H79A, H0756H80F, H0756H81G, H0756H82H, H0757B79E, H0757H75A, H0757H76C, H0757H78D, H0758H80B, H0758H82E, H0759H79A, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0851X88A, H0853F88B, H0853F89C, H0853F89E, H0853F89F, H0853F89
F197813
 
F197813 BEARING
H0032H84G, H0042081C, H0042082D, H0042083E, H0042B78C, H0042B80G, H0042C84L, H0042C87A, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H005201RS, H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0062H79M, H0064H78D, H0064H80F, H0064H82
F523057
 
F523057 BEARING, DRIVESHAFT LOWER
H0756H80F, H0756H81G, H0756H82H, H0758H80B, H0758H82E, H0850H79A, H0850H80A, H0850H81C, H0851H79A, H0851X88A, H0853F88B, H0853F89C, H0853F89E, H0855H79A, H0856A89A, H0856B80H, H0856C87A, H0856C87B, H0856F84A, H0856F85A, H0856F86A, H0856H82K, H0856Y89
FK85228-1
 
FK85228-1 BEARING CAGE W/ROLLER
H0202B81M, H0202H82N, H0252B83G, H0257F88A, H0257F88B, H0307H81D, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0353H81N, H0353H82P, H0355D89A, H0356F89B, H0357C86A, H0357C87A, H0357C88B, H0357F88A, H0357F89C, H0357G90A, H0357H83N, H0456B80L, H0457H82
Back to top