F338129-1 Force BOOT


F338129-1 BOOT Force H0257F88A, H0257F88B, H0352F90B, H0352F90C, H0352H77H, H0352H79L, H0353E91A, H0353E91B, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0355D89A, H0356F89B, H0356H75F, H0357C88B, H0357F89C, H0357G90A, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83 BOOT
F338129-1 BOOT Force
Rating:
13

Buy BOOT F338129-1 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Force entire parts catalog list:

H0257F88A 1988,1989
H0257F88B 1988,1989,1991
H0352F90B 1990
H0352F90C 1990
H0352H77H 1977,1978
H0352H79L 1979
H0353E91A 1991
H0353E91B 1991
H0353H78K 1978
H0353H80M 1980
H0353H81N 1981
H0353H82P 1982
H0355D89A 1989
H0356F89B 1989
H0356H75F 1975,1976,1977
H0357C88B 1988
H0357F89C 1989
H0357G90A 1990
H0456B78J 1978
H0456B79K 1979
H0456B80L 1980,1981
H0457H82N 1982
H0457H83P 1983,1984
H0503B83A 1983
H0503H84B 1984
H0504H88C 1988
H0504H88D 1988
H0504P89B 1989
H0505C89B 1989
H0507A89C 1989
H0507A89D 1989
H0507A90A 1990
H0507A90B 1990
H0507A90C 1990
H0507A90D 1990
H0507A91A 1991
H0507A91C 1991
H0507A92A 1992
H0507B85A 1985
H0507C86A 1986
H0507C87A 1987
H0507C87C 1987
H0507C88B 1988
H0507E91B 1991
H0507F87B 1987
H0507F88A 1988
H0507H81A 1981
H0507H82B 1982
H0507Z89B 1989
H0555H74G 1974,1976

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M8 by 100 mm 4
B 6V-6640 Sealant -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
If necessary, install the plate for the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install" for the correct procedure.
Illustration 1 g02010373
Install Tooling (A) to Positions (X) in the cylinder block.
Illustration 2 g02383016
Ensure that engine oil pan (10) is clean and free from damage.
Position a new gasket (4) onto engine oil pan (10).
Install new isolators (14) and isolators (12) to the engine oil pan. Do not install the isolators (12) in Positions (X). Refer to Illustration 1. Note: The isolators are held captive by the gasket.
Ensure that the gasket surface of the isolating frame is clean and from damage.
Align the assembly of the engine oil pan with Tooling (A). Install the assembly of the engine oil pan to the isolating frame.
Install bolts (13) and bolts (11) to the isolators finger tight.
Illustration 3 g02010374
(X) Position of guide studs.
(Z) Position of short bolts.
Sequence for tightening the bolts
Tighten bolts (13) and bolts (11) to a torque of 22 N m (195 lb in). Tighten the bolts in the sequence that is shown in Illustration 3.
Remove Tooling (A).
Illustration 4 g02010375
Sequence for tightening the bolts
Install the four remaining bolts (11). Tighten the isolating screws to a torque of 22 N m (195 lb in). Tighten the bolts in the sequence that is shown in Illustration 4.
Illustration 5 g02382976
Install a new O-ring seal (6) (not shown) to drain plug (5). Install drain plug (5) to engine oil pan (7). Refer to Illustration 2. Tighten the oil drain plug to a torque of 34 N m (301 lb in).
If necessary, follow Step 13.a through Step 13.c in order to install the assembly of the dipstick tube.
Install a new seal (3) to tube assembly (2).
Apply Tooling (B) to nut (1). Install the tube assembly to the engine oil pan. Note: Ensure that the orientation of the tube assembly is correct.
Tighten nut (1) to a torque of 18 N m (159 lb in).
If necessary, follow Step 14.a through Step 14.c in order to install oil level switch (7) to engine oil pan (10).
Install a new O-ring seal (8) (not shown) to oil level switch (7).
Install oil level switch (7) to engine oil pan (10). Tighten the oil level switch to a torque of 34 N m (301 lb in).
Connect the Original Equipment Manufactures (OEM) wiring harness to wiring harness assembly (9) for oil level switch (7). Install a new cable strap to the wiring harness assembly. Note: Ensure that the cable strap meets the OEM specification.
Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Oil Filter Change" for the correct procedure.


Back to top