F345427-1 BRACKET, STARTER MOUNTING Force
H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503B83A, H0503H84B, H0504H88C, H0504H88D, H0504P89B, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507B85A, H0507C86A, H0507C87A, H0507C87C, H0507C88
BRACKET
Price: query
Rating:
Compatible models:
H0356H75F
H0456B78J
H0456B79K
H0456B80L
H0457H82N
H0457H83P
H0503B83A
H0503H84B
H0504H88C
H0504H88D
H0504P89B
H0507A90A
H0507A90B
H0507A90C
H0507A90D
H0507A91A
H0507A91C
H0507A92A
H0507B85A
H0507C86A
H0507C87A
H0507C87C
H0507C88B
H0507E91B
H0507F87B
H0507F88A
H0507H81A
H0507H82B
H0507Z89B
H0555H74G
Force
Force entire parts catalog list:
- POWER HEAD » F345427-1
- POWER HEAD » F345427-1
- POWER HEAD » F345427-1
- POWER HEAD » F345427-1
- POWER HEAD » F345427-1
- POWER HEAD » F345427-1
- POWER HEAD » F345427-1
- POWER HEAD » F345427-1
- RECIRCULATION SYSTEM AND STARTER BRACKETS » F345427-1
- RECIRCULATION SYSTEM AND STARTER BRACKETS » F345427-1
- RECIRCULATION SYSTEM AND STARTER BRACKETS » F345427-1
- RECIRCULATION SYSTEM AND STARTER BRACKETS » F345427-1
- RECIRCULATION SYSTEM AND STARTER BRACKETS » F345427-1
- RECIRCULATION SYSTEM AND STARTER BRACKETS » F345427-1
- RECIRCULATION SYSTEM AND STARTER BRACKETS » F345427-1
- RECIRCULATION SYSTEM AND STARTER BRACKETS » F345427-1
- RECIRCULATION SYSTEM AND STARTER BRACKETS » F345427-1
- RECIRCULATION SYSTEM AND STARTER BRACKETS » F345427-1
- POWER HEAD » F345427-1
- POWER HEAD » F345427-1
- POWER HEAD » F345427-1
- RECIRCULATION SYSTEM & STARTER BRACKETS » F345427-1
- RECIRCULATION SYSTEM AND STARTER BRACKETS » F345427-1
- RECIRCULATATION SYSTEM AND STARTER BRACKETS » F345427-1
- FUEL RECIRCULATION COMPONENTS » F345427-1
- RECIRCULATION SYSTEM AND STARTER BRACKETS » F345427-1
- POWER HEAD » F345427-1
- POWER HEAD » F345427-1
- RECIRCULATION SYSTEM AND STARTER BRACKETS » F345427-1
- POWER HEAD » F345427-1
Information:
Illustration 1 g00812427
Schematic for the circuit for the compression brake lampTest Step 1. Inspect the Bulb for the Compression Brake Lamp
Turn the keyswitch to the "OFF/RESET" position.
Remove the bulb. Inspect the bulb for damage and for a broken filament.Expected Result:The bulb should be free from apparent damage. The filament should be intact.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Replace the bulb.Verify that the repair eliminates the problem.STOPTest Step 2. Inspect Electrical Connectors And Wiring.
Illustration 2 g00812521
Terminal locations for ECM connector P1
Thoroughly inspect ECM machine harness connector J1/P1, the firewall bulkhead connector, and the compression brake lamp (terminal 10). Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM machine harness connector that are associated with the compression brake lamp.
Check the ECM machine harness connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the harness and wiring for abrasions and for pinch points from the battery to the ECM.Expected Result:All connectors, pins and sockets should be completely coupled and/or inserted and the harness and wiring should be free of corrosion, abrasion or pinch points.Results:
OK - Proceed to Test Step 3.
Not OK - Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.STOPTest Step 3. Check For Normal Operation Of The Lamp.
Connect ET to the service tool connector.
Turn the keyswitch to the ON position.
Access the screen for the overrides on ET.
Activate the "Jake Brake Low/High" or the "Jake Brake Med/High" override.
Monitor the compression brake lamp.
The lamp should turn on when the override is active.
Deactivate the override.
The lamp should turn off when the override is deactivated.Expected Result:The compression brake lamp turns on when the override is activated. The compression brake lamp turns off when the override is deactivated.Results:
Yes - The compression brake lamp appears to operating correctly at this time.STOP
No - Proceed to Test Step 4.Test Step 4. Check the Harness for a Short to Ground
Illustration 3 g00812582
Terminal locations to check for short to ground
Disconnect ECM machine harness connector J1/P1.
Remove the bulb for the compression brake lamp from the socket.
Measure the resistance between P1:10 (compression brake lamp) and the following terminals:
P1:3 (analog return)
P1:61 (-battery)
P1:63 (-battery)Expected Result:The resistance should be greater than 20,000 Ohms for each reading.Results:
OK - The circuit is not shorted to ground. Proceed to Test Step 5.
Not OK - Repair: Wire 454-GN (compression brake lamp) is shorted to ground through one of the following wires in the harness:
P1:3 (analog return)
P1:61 (-battery)
P1:63 (-battery)Repair the circuit. Refer to the Electrical Schematic for more information.Verify that the repair eliminates the problem.STOPTest Step 5. Check the Harness for a Short to +Battery
Illustration 4 g00812762
Terminal locations to check for a short to +battery
Disconnect ECM machine harness connector J1/P1.
Ensure that the bulb for the compression brake lamp is not installed.
Measure the resistance between P1:10 (compression brake lamp) and the following terminals:
P1:2 (analog power)
P1:48 (unswitched +battery)
P1:52 (unswitched +battery)
P1:70 (switched +battery)Expected Result:The resistance should be greater than 20,000 Ohms for each reading.Results:
OK - The circuit does not have a short to +battery. Proceed to Test Step 6.
Not OK - The circuit is shorted to +battery.Repair: Wire 454-GN (compression brake lamp) is shorted to +battery through one of the following wires in the harness:
P1:2 (analog power)
P1:48 (unswitched +battery)
P1:52 (unswitched +battery)
P1:70 (switched +battery)Repair the circuit. Refer to the Electrical Schematic for more information.Verify that the repair eliminates the problem.STOPTest Step 6. Check the Resistance through the Harness
Turn the keyswitch to the OFF/RESET position.
Disconnect ECM connector J1/P1.
Ensure that the compression brake lamp bulb is installed.
Measure the resistance between P1:10 (compression brake lamp) and 993-BR (analog return) at the lamp socket.Expected Result:The resistance through the wires and the bulb should be less than 25 Ohms.Results:
OK - The ECM may not be providing a proper ground path for the compression brake lamp. Proceed to Test Step 7.
Not OK - There is an open circuit in the harness or connectors.Repair: Repair the circuit. Refer to the Electrical Schematic for more information.Verify that the repair eliminates the problem.STOPTest Step 7. Check the voltage at the ECM
Illustration 5 g00812868
ECM connector P1 (harness side)
Turn the keyswitch to the OFF/RESET position.
Ensure that ECM connector J1/P1 and all other connectors are properly connected.
Remove 454-GN at P1:10 (compression brake lamp) and 993-BR at P1:3 (analog return).
Install ET at the service tool connector.
Turn the keyswitch to the ON position.
Access the screen for the overrides on ET.
Activate the "Jake Brake Low/High" or the "Jake Brake Med/High" override.
Measure the voltage between P1:10 (compression brake lamp) and P1:3 (analog return).
Turn the keyswitch to the OFF/RESET position.Expected Result:The voltage across the terminals should be within 1 VDC from the
Parts bracket Force:
F458774
F458774 BRACKET, REAR RETAINER
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0456B78J, H0456B79K, H0456B80L, H0457H82N, H0457H83P, H0503B83A, H0503H84B, H0507B85A, H0507C86A, H0507C87A, H0507C87C, H0507F87B, H0507F88A, H0507H81A, H0507H82B, H0555H74
F191993-1
F191993-1 BRACKET, CHOKE CABLE (NOT SHOWN)
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0356H75F, H0456B78J, H0503B83A
F433612
F433612 BRACKET SHIFT ROD
H0352H77H, H0352H79L, H0353H78K, H0353H80M, H0353H81N, H0353H82P, H0503B83A
F658501
F481743
817977A 1
817977A 1 BRACKET
H0504P89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507Z89B
F98427-3
F660978