26856 Force BUSHING


26856 BUSHING Force H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201TS, H025201U BUSHING
26856 BUSHING Force
Rating:
68

Buy BUSHING 26856 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Force entire parts catalog list:

H005201SD 1996,1997
H005201TS 1997
H005201UD 1998,1999
H0052C88A 1988,1989,1990,1991,1992,1993,1994,1995
H0091H84D 1984
H009201RS 1995
H009201SD 1996,1997
H009201UD 1998
H009201US 1998
H0092284D 1984,1985,1986,1987,1988,1989,1990,1991,1992,1993,1994,1995
H0092H84L 1984
H0092S88A 1988
H0092S91A 1991
H0093S91A 1991
H015201RS 1995
H015201US 1998
H015211SS 1996,1997
H0152C84K 1984
H0152S89A 1989
H025201RD 1995,1996
H025201TD 1997
H025201TS 1997
H025201US 1998
H0903E91H 1991,1992,1993,1994

Information:

Start By:a. remove piston cooling jetsb. remove oil pan 1. Use tool (A) to turn the engine flywheel to move counterweights (2) in position for the removal of the main bearing caps. If necessary, the counterweights can be removed.2. Remove the four bolts, and remove bearing caps (1) from the crankshaft. 3. Remove lower bearing halves (3) from bearing caps (1). 4. Remove thrust plates (4) from each side of the center main bearing.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and cylinder block. This can cause damage to either or both.
5. Install tool (B) in the oil hole in the crankshaft journal, and remove upper main bearing halves (5) as the crankshaft is turned and the bearing is moved out of the cylinder block. On the center main journal that has no oil hole, put a thin piece of soft material that will not damage the crankshaft journal against the end of the bearing, opposite the tab. Hit the bearing with the soft material until the tab of the bearing is free from the cylinder block. Remove the upper half of the main bearing.Install Crankshaft Main Bearings
Make sure the upper and lower halves of bearings are installed so the bearing tabs fit into the notch in cylinder block and bearing caps.
Install the main bearings dry when the clearance checks are made. Put clean engine oil on the main bearings for final assembly. 1. Install tool (B) in the oil hole of the crankshaft. Put the upper bearing half (with oil hole) in position on the crankshaft. Use tool (A) to turn the engine flywheel and push the bearing half in position with tool (B). 2. Put clean engine oil on thrust plates (1), and install the plates on each side of the center main bearing. 3. Make sure bearing caps (2) are clean, and install lower bearing halves (3) in the caps.The serviceman must be very careful to use Plastigage, tool (D) correctly. The following points must be remembered:... Make sure that the backs of the bearings and the bores are clean and dry.... Make sure that the bearing locking tabs are properly seated in their slots.... The crankshaft must be free of oil where the Plastigage touches it.... If the main bearing clearances are checked with the engine upright or on its side, the crankshaft will have to be lifted up with a force equal to the weight of the crankshaft and held against the crown of the bearing. If the crankshaft is not supported, the weight of the crankshaft will cause incorrect readings.... Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.... Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.... Do not turn the crankshaft with the Plastigage installed.... Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.... Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 10 mm (.004 in) the readings may be low by 0.013 to 0.025 mm (.0005 to .0010 in). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider that the other.For complete details concerning measuring bearing clearances, see Engine Bearings And Crankshafts, Form No. SEBD0531. 4. Check the bearing clearances with Plastigage (D) as follows:a. Put a piece of the Plastigage on the surface of the lower bearing half.b. Install main bearing caps (2) with the word "Front" and the cast part number toward the front of the cylinder block. Each cap has a number on the bottom surface and must be installed in the same position as the correct number on the right side of the block pan rail.c. Put Fel-Pro C100 Lubricant on the main bearing cap bolts, and hand tighten in number sequence to a torque of 190 14 N m (140 10 lb. ft ft.). Then hand tighten the bolts in the number sequence shown 180° 5° more.d. Remove the caps, and measure the Plastigage. The main bearing clearance must be 0.122 to 0.241 mm (.0048 to .0095 in.).5. Put the bearing caps in position, and tighten the bolts as in Step 4. An impact wrench can be used for the final 180° 5° torque tightening turn.
Each counterweight has a number, and must be installed in the same position as the correct number on the crankshaft mounting pad to prevent damage to the crankshaft when the engine is run.
6. Make sure the dowels are in position, and install counterweights (8) on the crankshaft as follows:a. Lubricate bolt threads, shank and bolt seat with 6V4876 Molykote Paste Lubricant before assembly.b. Tighten the bolts in the counterweights to 200 5 N m (150 4 lb. ft.).c. Loosen the bolts in the counterweights.d. Tighten the bolts in the counterweights to 70 5 N m (50 4 lb. ft.).e. Turn bolts in all counterweights an additional 120° 5°. 7. Check the crankshaft end play with tooling (C). The end play is controlled by the thrust plates on the center main bearing. End play with new bearings is 0.17 to 0.63 mm (.007 to .025 in.).End By:a. install piston cooling jetsb. install oil pan


Parts bushing Force:

FT8918
 
FT8918 BUSHING GUIDE SET
H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0064H80F, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0075H79A, H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0095B81G, H0095H82H, H0101B78A, H0121B79A, H0125H79E, H0202B80L, H0202B81M, H0202H79K, H0202H82
F197767-1
 
F197767-1 BUSHING, FUEL LINE
H0060B76A, H0060B78B, H0060H79C, H0060H80D, H0062B78J, H0062H79K, H0062H79M, H0064H78D, H0064H80F, H0064H82H, H0067H79C, H0070B79A, H0071H81B, H0071H82C, H0071H83D, H0071H84E, H0072B81D, H0072H79B, H0072H80C, H0072H82E, H0075H79A, H0082H76G, H0082H78
26841
 
26841 BUSHING
H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201TS, H025201US
97896
 
97896 BUSHING
H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201TS, H025201US, H0407E92C, H0706A91B, H075312SD, H075312UD, H0903E91H, H1201A90A, H1501E89A
819493
 
819493 BUSHING-Swivel Bracket
H0903E91H, H1201A90A, H1501E89A
819513
 
819513 BUSHING
H0706A91B, H075312SD, H075312UD, H075412VD, H090312RD, H0903E91H, H090412SD, H090412UD, H090422VD, H1201A90A, H120412RD, H120412SD, H120412UD, H1501E89A
85557
 
85557 BUSHING
H025201RD, H025201TD, H025201TS, H025201US
830054
BUSHING-FLANGED
830054 BUSHING-FLANGED
H025201RD, H025201TD, H025201TS
Back to top