823507 Force BUSHING


823507 BUSHING Force H040312RD, H040312SD, H040312UD BUSHING
823507 BUSHING Force
Rating:
103

Buy BUSHING 823507 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 16
 

Compatible models:

Force entire parts catalog list:

H040312RD 1995
H040312SD 1996,1997
H040312UD 1998,1999

Information:

the site. The correct air/fuel ratio also helps ensure stable operation. To adjust the air/fuel ratio, perform the following procedure.
Connect a properly calibrated emissions analyzer to the exhaust stack.
Connect the Caterpillar Electronic Technician (Cat ET) to the service tool connector. Refer to Systems Operation/Testing and Adjusting, "General Information (Electronic Control System)".
Verify that the "Fuel Quality" and "Gas Specific Gravity" parameters are programmed correctly. Use the values that are obtained from the Caterpillar Software, LERW4485, "Gas Engine Rating Pro (GERP)".
Verify that the value for the "Fuel Specific Heat Ratio" parameter is correct. Enter a value of 1.4 for processed, dry pipeline natural gas.
Start the engine. Increase the engine speed to high idle rpm. Verify that the engine is stable.If the engine is unstable, perform the following procedure.
Record the values for these parameters:
"Governor Gain Factor"
"Governor Stability Factor"
"Governor Compensation Factor"
Set the values for the "Governor Gain Factor", "Governor Stability Factor", and "Governor Compensation Factor" parameters to zero.
Adjust the "Fuel Quality" parameter until the engine becomes stable and the exhaust oxygen is approximately four percent. Verify that the exhaust port temperatures are below the setpoint for a warning.
Adjust the primary governor. Refer to Systems Operation/Testing and Adjusting, "Engine Governing - Adjust".
Close the main circuit breaker for the generator in order to engage the generator.Note: When the engine load becomes greater than 25 percent, the air/fuel ratio control will operate in the feedback mode.
Slowly ramp the load up to 30 percent.Note: When the air/fuel ratio control is in the feedback mode, the Fuel Correction Factor (FCF) may no longer be 100 percent. The Electronic Control Module may adjust the FCF in order to compensate for the fuel quality and for the ambient conditions.
Set the "Desired Emission Gain Adjustment" parameter to a value of "100".
Verify that the reading on Cat ET for the generator's power output agrees with the switchgear's reading.If the readings do not agree, adjust the "Generator Output Power Sensor Scale Factor" and/or the "Generator Output Power Sensor Offset" parameters. Also, make sure that the "Engine Output Power Configuration" and the "Engine Driven Accessory Load Configuration" parameters are accurately programmed. Refer to Systems Operation/Testing and Adjusting, "Electronic Control System Parameters".
Slowly ramp up to 70 percent load. Verify that the engine is stable.If the engine is unstable, adjust the auxiliary governor. Refer to Systems Operation/Testing and Adjusting, "Engine Governing - Adjust".
Verify that the NOx emissions are above the desired full load setting.
Slowly ramp up to 100 percent load.
Verify that the reading on Cat ET for the generator's power output agrees with the switchgear's reading.
Adjust the "Desired Emission Gain Adjustment" parameter in order to obtain the values of emissions that are required at the site.
To lean the air/fuel mixture, decrease the gain adjustment.
To richen the air/fuel mixture, increase the gain adjustment.A small change in the "Desired Emission Gain Adjustment" causes a large change in the actual exhaust emissions. For example, an adjustment of one percent in the parameter's value will result in a change of 20 to 40 ppm in the actual level of NOx.When you adjust the exhaust emissions, make a small change in the value of the gain. Wait until the system stabilizes. Check the emissions again. Repeat the process until the desired emissions level is achieved.Use the emissions analyzer in order to verify that the values of emissions meet the requirements of the site.


Parts bushing Force:

812707
BUSHING
812707 BUSHING
H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201TS, H025201US, H040312RD, H040312SD, H040312UD, H0407E92
42182 1
 
42182 1 BUSHING
H040312RD, H0407E92C
26954
 
26954 BUSHING
H040312RD, H040312SD, H040312UD
48475
 
48475 BUSHING
H040312RD, H040312SD, H040312UD, H075412VD, H090312RD, H090412SD, H090412UD, H090422VD, H120412RD, H120412SD, H120412UD
822003
BUSHING
822003 BUSHING
H040312RD, H040312SD, H040312UD, H075312SD, H075312UD, H075412VD, H090412SD, H090412UD, H090422VD, H120412SD, H120412UD
823589
 
823589 BUSHING
H040312RD, H040312SD, H040312UD
818968
 
818968 BUSHING, GROMMET
H040312RD, H040312SD, H040312UD, H075312SD, H075312UD, H075412VD, H090312RD, H090412SD, H090412UD, H090422VD, H120412RD, H120412SD, H120412UD
822482
BUSHING
822482 BUSHING
H040312RD, H040312SD, H040312UD
Back to top