F15159 Force INSULATOR


F15159 INSULATOR Force H0252B83G, H0257F88A, H0257F88B, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0357C86A, H0357C87A, H0357C88B, H0357F88A, H0357F89C, H0357G90A, H040312RD, H0407E92C, H0503H84B, H0504H88C, H0504H88D, H0504P89 INSULATOR
F15159 INSULATOR Force
Rating:
103

Buy INSULATOR F15159 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 21
 

Force entire parts catalog list:

H0252B83G 1983,1984
H0257F88A 1988,1989
H0257F88B 1988,1989,1991
H0350H78L 1978
H0351H76K 1976
H0352F90B 1990
H0352F90C 1990
H0353E91A 1991
H0353E91B 1991
H0355D89A 1989
H0356F89B 1989
H0357C86A 1986
H0357C87A 1987
H0357C88B 1988
H0357F88A 1988
H0357F89C 1989
H0357G90A 1990
H040312RD 1995
H0407E92C 1992,1993,1994
H0503H84B 1984
H0504H88C 1988
H0504H88D 1988
H0504P89B 1989
H0505C89B 1989
H0507A89C 1989
H0507A89D 1989
H0507A90A 1990
H0507A90B 1990
H0507A90C 1990
H0507A90D 1990
H0507A91A 1991
H0507A91C 1991
H0507A92A 1992
H0507B85A 1985
H0507C86A 1986
H0507C87A 1987
H0507C87C 1987
H0507C88B 1988
H0507E91B 1991
H0507F87B 1987
H0507F88A 1988
H0507Z89B 1989
H0606H84A 1984,1985,1989
H0706A91B 1991,1992,1993,1994,1995
H075312SD 1996,1997
H075312UD 1998
H075412VD 1999
H090312RD 1995
H0903E91H 1991,1992,1993,1994
H090412SD 1996,1997
H090412UD 1998
H090422VD 1999
H090LD91D 1991
H1201A90A 1990,1991,1992,1993,1994
H120412RD 1995
H120412SD 1996,1997
H120412UD 1998,1999
H120LD91D 1991
H120LD92B 1992
H1501E89A 1989,1990,1991,1992,1993,1994

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
B 1U-6683 Ring Expander 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03003219
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Position the spring for oil control ring (3) into the oil ring groove in piston (4). The central wire must be located inside the end of the spring.
Position the oil control ring with the word "TOP" in the upward position. Use Tooling (B) to install oil control ring (3) over the piston and the spring. Note: Ensure that the central wire is 180 degrees from the ring gap.
Use Tooling (B) to install intermediate compression ring (2) into the second groove in piston (4). The word "TOP" must be upward.
Use Tooling (B) to install top compression ring (1) into the top groove in piston (4). The word "TOP" must be upward.
Position the piston ring gaps at approximately 120 degrees away from each other. Note: A new piston assembly is supplied with new piston rings.
Illustration 2 g03001779
(A) Cut away for piston cooling jet
(9) Upper shell for connecting rod
(X) Identification marks
(Y) Location tag on connecting rod shells
(Z) Location tag in connecting rod for shells (not shown)
(10) Lower shell for connecting rod cap
Use Illustration 2 as an assembly guide.
Illustration 3 g03001216
Lubricate bushing (8) for piston pin (6) in the connecting rod with clean engine oil. Lubricate the bore for the piston pin in piston (4) with clean engine oil.
Install piston pin (6) to piston (4). Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of 45° 5°C (113° 9°F).
Use Tooling (A) in order to install circlips (5) to the piston pin bore in piston (4). Note: Ensure that the circlips are seated in the grooves in the piston.
Install upper bearing shell (9) into connecting rod (7). Ensure that the locating tab for the upper bearing shell is correctly seated in slot in the connecting rod.
Install lower bearing shell (10) into connecting rod cap (11). Ensure that the locating tab for the lower bearing shell is correctly seated in the slot in the connecting rod cap.
Temporarily install connecting rod cap (11) and bolts (12) to connecting rod (7) when the assembly is out of the engine. Ensure that the etched number on connecting rod cap matches the etched number on connecting rod. Ensure the correct orientation of the connecting rod cap. The locating tab for the upper bearing shell and the lower bearing shell should be on the same side. Tighten bolts (12) to a torque of 20 N m (177 lb in).
Repeat Step 1 through Step 13 for the remaining piston and connecting rod assemblies. Note: Fracture split connecting rods should not be left without the connecting rod caps installed.End By:
Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install" for the correct procedure.


Parts insulator Force:

F15160
 
F15160 INSULATOR WASHER
H0252B83G, H0257F88A, H0257F88B, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0353E91A, H0353E91B, H0355D89A, H0356F89B, H0357C86A, H0357C87A, H0357C88B, H0357F88A, H0357F89C, H0357G90A, H040312RD, H040312SD, H040312UD, H0407E92C, H0503H84B, H0504H88
97861
 
97861 INSULATOR, Solenoid
H090412SD, H120412SD
Back to top