F685301-2 Force CD UNIT (BLUE)


F685301-2 CD UNIT (BLUE) Force H0505C89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507E91B, H0507Z89B, H085LD89A, H085LD89B, H085LD89C, H0903E91H, H0903F90B, H0903F90C, H0903F91A, H0903F91C, H0906A90A, H090LD90A, H090LD90 CD
F685301-2 CD UNIT (BLUE) Force
Rating:
23

Buy CD UNIT (BLUE) F685301-2 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 15
 

Force entire parts catalog list:

H0505C89B 1989
H0507A89C 1989
H0507A89D 1989
H0507A90A 1990
H0507A90B 1990
H0507A90C 1990
H0507A90D 1990
H0507A91A 1991
H0507A91C 1991
H0507A92A 1992
H0507E91B 1991
H0507Z89B 1989
H085LD89A 1989
H085LD89B 1989
H085LD89C 1989
H0903E91H 1991,1992,1993,1994
H0903F90B 1990
H0903F90C 1990
H0903F91A 1991
H0903F91C 1991
H0906A90A 1990
H090LD90A 1990
H090LD90C 1990
H1201A90A 1990,1991,1992,1993,1994
H120LD90A 1990
H120LD90B 1990
H120LD90C 1990
H125LD89A 1989
H125LD89B 1989
H1501E89A 1989,1990,1991,1992,1993,1994

Information:


If no oil pressure is indicated, STOP the engine. If maximum coolant temperature is exceeded, STOP the engine. Engine damage can result.
Engine Oil Pressure - The oil pressure should be greatest after a cold engine is started. The typical engine oil pressure with SAE10W40 is 400 to 480 kPa (58 to 69 psi) at rated rpm.A lower oil pressure is normal at low idle. If the load is stable and the gauge reading changes, perform the following procedure:
Remove the load.
Stop the engine.
Check and maintain the oil level.
Jacket Water Coolant Temperature - Typical temperature range is 82° to 94°C (179.6° to 169.2°F). This temperature range will vary according to engine load and the ambient temperature. A 100 kPa (14.5 psi) radiator cap must be installed on the cooling system. The maximum temperature for the cooling system is 108° C (226.4° F). The engine coolant temperature is regulated by the engine sensors and the engine ECM. This programming cannot be altered. An engine derate can occur if the maximum engine coolant temperature is exceeded.If the engine is operating above the normal range, reduce the engine load. If high coolant temperatures are a frequent event, perform the following procedures:
Reduce the load and the engine rpm.
Determine if the engine must be shut down immediately or if the engine can be cooled by reducing the load.
Inspect the cooling system for leaks. If necessary, consult your Caterpillar dealer for assistance.
Tachometer - This gauge indicates engine speed (rpm). When the throttle control lever is moved to the full throttle position without load, the engine is running at high idle. The engine is running at the full load rpm when the throttle control lever is at the full throttle position with maximum rated load.
To help prevent engine damage, never exceed the high idle rpm. Over speeding can result in serious damage to the engine. Operation at speeds exceeding high idle rpm should be kept to a minimum.
Ammeter - This gauge indicates the amount of charge or discharge in the battery charging circuit. Operation of the indicator should be to the "+" side of "0" (zero).
Fuel Level - This gauge indicates the fuel level in the fuel tank. The fuel level gauge operates when the "START/STOP" switch is in the "on" position.
Service Hour Meter - The gauge indicates total operating hours of the engine.Indicator Lamps
Shutdown lamp
Warning lamp
Wait to start lamp
Low oil pressure lamp (On solid) and engine oil reset lamp (Flashing)For information, refer to this manual, "Monitoring System (Table for the Indicator Lamps)" for the sequence of operation of the shutdown lamp and the warning lamp.The function of the wait to start lamp is automatically controlled at engine start-up.The low oil pressure lamp has two functions.
The low oil pressure lamp is controlled by the engine ECM. If low oil pressure is detected, the lamp will be illuminated on solid. The reason for the illumination of the low-pressure lamp should be investigated immediately.
Low oil pressure lamp flashing, an engine oil change is required. The lamp must be reset, refer to this Operation and Maintenance Manual, "Engine Oil and Filter - Change" for more information.All lamps will illuminate for 2 seconds in order to check that the lamps are functioning when the keyswitch is turned to the ON position. If any of the lamps stay illuminated, the reason for illumination should be investigated immediately.Aftertreatment Lamps
For information on the aftertreatment lamp, refer to this Operation and Maintenance Manual, "Diesel Particulate Filter Regeneration".


Parts cd Force:

F685301
CD UNIT (BLUE)
F685301 CD UNIT (BLUE)
H0504H88D, H0504P89B, H0507Z89B, H0853F88B, H0853F89C, H0853F89E, H0853F89F, H0853F89G, H0856A89A, H0856A89H, H0856L89D, H0856Y89B, H1251A88C, H1251A89A, H1251A89B, H1251A89C, H1251A89D, H1251A89E
Back to top