26852 Force CAP-NYLON-IDLE ADJUST SCREW


26852 CAP-NYLON-IDLE ADJUST SCREW Force H009201SD, H009201UD, H009201US, H0092S88A, H015201US, H015211SS CAP
26852 CAP-NYLON-IDLE ADJUST SCREW Force
Rating:
78

Buy CAP-NYLON-IDLE ADJUST SCREW 26852 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 27
 

Force entire parts catalog list:

H009201SD 1996,1997
H009201UD 1998
H009201US 1998
H0092S88A 1988
H015201US 1998
H015211SS 1996,1997

Information:


Illustration 1 g00899164
SchematicTest Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF/RESET position.
Thoroughly inspect the J2/P2 ECM connector, the J3/P3 machine connector, and the connection to the user defined shutdown device (switch). Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and wiring for abrasion and for pinch points from the user defined shutdown device to the ECM.Expected Result:All connectors, pins, and sockets should be completely inserted and coupled. The harness and wiring should be free of corrosion, abrasion, and pinch points.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the circuit.Verify that the repair eliminates the problem. Stop.Test Step 2. Check the Status of the User Defined Shutdown
Connect the Caterpillar Electronic Technician (Cat ET) to the service tool connector.
Turn the keyswitch to the ON position.
Observe the status of "User Shutdown" on Cat ET.Expected Result:The status should be "Off".Results:
OK - Proceed to Test Step 3.
Not OK - Proceed to Test Step 4.Test Step 3. Short the Input at the Machine Connector
Use a suitable piece of wire to short J3:28 User Defined Shutdown to chassis ground.
Observe the status of "User Shutdown" on Cat ET.Expected Result:The status should be "On" when the terminal is grounded.Results:
OK - The circuit from machine connector J3 to the ECM is functioning properly. A problem may exist in either the user defined shutdown device (switch) or the circuit between the switch and machine connector P3.Repair: Troubleshoot the circuit between machine connector P3 and the switch. Repair the circuit and/or replace the switch, as needed. Stop.
Not OK - Proceed to Test Step 4.Test Step 4. Check the Harness for Shorts
Illustration 2 g00899168
P2 ECM connector
Disconnect ECM connector J2/P2.
Measure the resistance between P2:8 (User Defined Shutdown) and engine ground.Expected Result:The resistance should be greater than 20,000 Ohms.Results:
OK - Proceed to Test Step 5.
Not OK - There is a short circuit in the harness or a user defined shutdown device is activating the shutdown feature.Repair: Ensure that a user defined shutdown device is not activating the shutdown feature.Repair the circuit.Verify that the repair eliminates the problem. Stop.Test Step 5. Check the Resistance through the Harness
Turn the keyswitch to the OFF/RESET position.
Disconnect the J2/P2 ECM connector.
Use a suitable piece of wire to short J3:28 User Defined Shutdown to chassis ground.
Measure the resistance between P2:8 (User Defined Shutdown) and engine ground.
Remove the wire short.Expected Result:The resistance should be less than 10 Ohms when the terminal is grounded.Results:
OK - The resistance is within acceptable limits. Proceed to Test Step 6.
Not OK - There is an open circuit or excessive resistance in the harness.Repair: Repair the circuit.Verify that the repair eliminates the problem. Stop.Test Step 6. Short the Input at the ECM
Turn the keyswitch to the OFF/RESET position and install a 7X-1715 Adapter Cable (40 Pin Breakout T) at the J2/P2 ECM connector.
Turn the keyswitch to the ON position.
Observe the status of "User Shutdown" on Cat ET.
Use a suitable piece of wire to short P2:8 (User Defined Shutdown) to engine ground.
Observe the status of "User Shutdown" on Cat ET.Expected Result:The status should be "On" when the wire short is in place. The status should be "Off" when the wire short is removed.Results:
OK - The shutdown feature is working properly. Stop.
Not OK - The correct switch input appears at the ECM, but the ECM is not reading the switch input properly.Repair: Verify your results. Replace the ECM. Refer to Troubleshooting, "Replacing the ECM" before replacing the ECM. Stop.


Parts cap Force:

F17821
CAP ASSEMBLY
F17821 CAP ASSEMBLY
H0091H84D, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H0152C84K, H0152S89A, H0407E92C, H0507A91C, H0507E91B, H0706A91B, H0903E91D, H0903E91H, H0903F91A, H0903F91C, H1201A90A, H1501E89A
Back to top