F15179 Force COMMUTATOR*


F15179 COMMUTATOR* Force H0503H84B, H0504H88C, H0504H88D, H0504P89B, H0505C89B, H0507A89C, H0507A89D, H0507A90A, H0507A90B, H0507A90C, H0507A90D, H0507A91A, H0507A91C, H0507A92A, H0507B85A, H0507C86A, H0507C87A, H0507C87C, H0507C88B, H0507E91B, H0507F87B, H0507F88A, H0507Z89 COMMUTATOR
F15179 COMMUTATOR* Force
Rating:
23

Buy COMMUTATOR* F15179 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 15
 

Force entire parts catalog list:

H0503H84B 1984
H0504H88C 1988
H0504H88D 1988
H0504P89B 1989
H0505C89B 1989
H0507A89C 1989
H0507A89D 1989
H0507A90A 1990
H0507A90B 1990
H0507A90C 1990
H0507A90D 1990
H0507A91A 1991
H0507A91C 1991
H0507A92A 1992
H0507B85A 1985
H0507C86A 1986
H0507C87A 1987
H0507C87C 1987
H0507C88B 1988
H0507E91B 1991
H0507F87B 1987
H0507F88A 1988
H0507Z89B 1989
H0851X88A 1988
H0853F88B 1988,1989
H0853F89C 1989
H0853F89E 1989
H0853F89F 1989
H0853F89G 1989
H0856A89A 1989
H0856A89H 1989
H0856C87A 1987
H0856C87B 1987
H0856F84A 1984
H0856F85A 1985
H0856F86A 1986
H0856L89D 1989
H0856Y89B 1989
H0858C84H 1984
H085LD89A 1989
H085LD89B 1989
H085LD89C 1989
H0903E91D 1991
H0903F90B 1990
H0903F90C 1990
H0903F91A 1991
H0903F91C 1991
H0906A90A 1990
H090LD90A 1990
H090LD90B 1990,1991
H090LD90C 1990
H1201A90A 1990,1991,1992,1993,1994
H120LD90A 1990
H120LD90B 1990
H120LD90C 1990
H120LD91B 1991
H1251A88A 1988
H1251A88B 1988
H1251A88C 1988
H1251A89A 1989
H1251A89B 1989
H1251A89C 1989
H1251A89D 1989
H1251A89E 1989
H1251F84A 1984
H1251F86A 1986
H1251F87A 1987
H1251F87B 1987
H1251X85A 1985
H125LD89A 1989
H125LD89B 1989
H1408H83E 1983,1984
H1501E89A 1989,1990,1991,1992,1993,1994

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M8 by 50 mm 4
B 6V-6640 Sealant 1
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Illustration 1 g02193294
If necessary, follow Step 1.a through Step 1.d in order to assembly the engine oil cooler.
Ensure that engine oil cooler matrix (16) is clean, free from damage and restriction. Replace engine oil cooler matrix (16) if damaged or restricted.
Ensure that housing (19) is clean and free from damage. Replace spacer plate (19) if damaged.
Position new gaskets (17) onto engine oil cooler matrix (16). Install engine oil cooler matrix (16) to housing (19).
Install nuts (18) to the assembly of oil cooler (6). Tighten the nuts to a torque of 44 N m (32 lb ft).
Illustration 2 g02194374
Illustration 3 g02194313
Illustration 4 g02194394
Tightening sequence for the oil cooler with the high mounted oil filter
Clean the gasket surfaces of the cylinder block.
Install Tooling (A) into Position (C).
Position a new gasket (15) (not shown) onto Tooling (A).
Install assembly of oil cooler (6) to cylinder block. Install bolts (14) to the assembly of oil cooler (6). Tighten bolts (14) finger tight. Note: Ensure that the bolts of different lengths are installed in the correct position. Ensure that any brackets for the tube assemblies are location and correctly orientated.
Remove Tooling (A) and install remaining bolts (14).
Install oil filter base and install the bolts for the oil filter base finger tight. Refer to Illustration 4 and refer to Disassembly and Assembly, "Engine Oil Filter Base - Remove and Install" for the correct procedure.
Tighten bolts (14) to a torque of 22 N m (195 lb in) in sequence that is shown in Illustration 4. Tighten the remaining bolts that secure oil filter base to a torque of 22 N m (195 lb in).
Illustration 5 g02193293
Install new cable straps to engine wiring harness (3) that secure the wiring harness assembly to engine oil cooler (6).
Connect plastic tube assembly (1) to crankcase breather (2). Install the plastic tube assembly to the clips. Refer to Disassembly and Assembly, "Crankcase Breather- Install" for the correct procedure.
Connect plastic tube assembly (5) to crankcase breather canister (2) and crankcase breather valve (8). Refer to Disassembly and Assembly, "Crankcase Breather- Install" for the correct procedure.
Position clamp (13) onto engine oil cooler (6). Install bolt (12) and tighten the bolt to a torque 10 N m (88 lb in).
Position bracket (7) onto engine oil cooler (6) and install bolts (4). Tighten the bolt to a torque of 18 N m (159 lb in). Note: Ensure that locating pin for the bracket is correctly located into the engine oil cooler.
Install a new seal (11) (not shown) to the tube assembly. Apply Tooling (B) to nut (9).
Install the tube assembly to the engine oil pan. Install bolt (10) to the bracket for tube assembly.
Tighten bolt (10) to a torque of 22 N m (195 lb in).
Tighten nut (9) to a torque of 18 N m (159 lb in).
Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Check level of the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil Level - Check" for the correct procedure. End By:
Install the mouning bracket for the Electronic Control Module (ECM) . Refer to Disassembly and Assembly, "ECM Mounting Bracket- Remove and Install" for the correct procedure.


Back to top